DTC    P0710    Transmission Fluid Temperature Sensor "A" Circuit

DTC    P0712    Transmission Fluid Temperature Sensor "A" Circuit Low Input

DTC    P0713    Transmission Fluid Temperature Sensor "A" Circuit High Input

for Preparation Click here


DESCRIPTION

The ATF (Automatic Transmission Fluid) temperature sensor converts the fluid temperature into a resistance value which is input into the ECM.
G031389E04
The ECM applies a voltage to the temperature sensor through ECM terminal OIL.
The sensor resistance changes with the transmission fluid temperature. As the temperature becomes higher, the sensor resistance decreases.
One terminal of the sensor is grounded so that the sensor resistance decreases and the voltage goes down as the temperature becomes higher.
The ECM calculates the fluid temperature based on the voltage signal.

DTC No.
DTC Detection Condition
Trouble Area
P0710
(a) and (b) are detected momentary within 0.5 sec. when neither P0712 or P0713 is not detected (1-trip detection logic)
(a) ATF temperature sensor resistance is less than 79 Ω.
(b) ATF temperature sensor resistance is more than 156 kΩ.

HINT:
Within 0.5 sec., the malfunction switches from (a) to (b) or from (b) to (a)

  1. Open or short in ATF temperature sensor circuit
  2. Transmission wire (ATF temperature sensor)
  3. ECM
P0712
ATF temperature sensor resistance is less than 79 Ω for 0.5 sec. or more (1-trip detection logic)
  1. Short in ATF temperature sensor circuit
  2. Transmission wire (ATF temperature sensor)
  3. ECM
P0713
ATF temperature sensor resistance is more than 156 kΩ when 15 minutes or more after the engine start
DTC is detected for 0.5 sec. or more (1-trip detection logic)
  1. Open in ATF temperature sensor circuit
  2. Transmission wire (ATF temperature sensor)
  3. ECM

MONITOR DESCRIPTION

These DTCs indicate an open or short in the automatic transmission fluid (ATF) temperature sensor (TFT sensor) circuit. The automatic transmission fluid (ATF) temperature sensor converts ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature, and the ECM detects an open or short in the ATF temperature circuit. If the resistance value of the ATF temperature is less than 79 Ω*1 or more than 156 kΩ*2, the ECM interprets this as a fault in the ATF sensor or wiring. The ECM will turn on the MIL and store the DTC.
*1: 150°C (302°F) or more is indicated regardless of the actual ATF temperature.
*2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.

HINT:
The ATF temperature can be checked on the intelligent tester display.


WIRING DIAGRAM


G031390E02


INSPECTION PROCEDURE


DATA LIST

HINT:
Using the intelligent tester Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to shorten labor time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the engine switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the engine switch on (IG) position.

  5. Turn on the tester.

  6. Select the item "Enter / Power train / ECT / Data List".

  7. Follow the instructions on the tester and read the Data List.

    Item
    		Measurement Item/
    Range (display)
    		Normal Condition
    A/T Oil Temperature 1
    		ATF Temp. Sensor Value/
    min.: -40°C (-40°F)
    max.: 215°C (419°F)
    1. After Stall Test;
      Approx. 80°C (176°F)
    2. Equal to ambient temperature when cold soak

    HINT:
    When DTC P0712 is output and intelligent tester output is 150°C (302°F) or more, there is a short circuit.
    When DTC P0713 is output and intelligent tester output is -40°C (-40°F), there is an open circuit.
    Measure the resistance between terminal OIL (OT) and body ground.


    Temperature Displayed
    		Malfunction
    -40°C (-40°F)
    		Open circuit
    150 °C (302°F) or more
    		Short circuit

    HINT:
    If a circuit related to the ATF temperature sensor becomes open, P0713 is immediately set (in 0.5 second). When P0713 is set, P0711 cannot be detected.
    It is not necessary to inspect the circuit when P0711 is set.

1.INSPECT TRANSMISSION WIRE (ATF TEMPERATURE SENSOR)


    C110342E01

  1. Disconnect the transmission wire connector from the transmission.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    		Specified Condition
    1 (E2) - 9 (OIL)
    		79 Ω to 156 kΩ
    1 (E2) - Body ground
    		10 kΩ or higher
    9 (OIL) - Body ground
    		10 kΩ or higher

    HINT:
    If the resistance is out of the specified range with either the ATF temperature shown in the table below, the driveability of the vehicle may decrease.

    Resistance:
    ATF Temperature
    		Specified Condition
    20 °C (68°F)
    		3 to 4 kΩ
    110°C (230°F)
    		0.22 to 0.28 kΩ



NG
REPAIR OR REPLACE TRANSMISSION WIRE
OK


2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)


    C106186E31

  1. Connect the transmission wire connector to the transmission.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    		Specified Condition
    E7 - 27 (OIL) - E7 - 26 (EOIL)
    		79 Ω to 156 kΩ

  1. Measure the resistance according to the value(s) in the table below.

    Resistance (Check or short):
    Tester Connection
    		Specified Condition
    E7 - 27 (OIL) - Body ground
    		10 kΩ or higher
    E7 - 26 (EOIL) - Body ground
    		↑



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM