CLEARANCE SONAR SYSTEM > CUSTOMIZE PARAMETERS

for Preparation Click here



CUSTOMIZE PARAMETERS (INTELLIGENT TESTER)

  1. The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.


Warning 
DISPLAY
DEFAULT
CONTENTS
SETTING
Front Buzzer Onset Range
Wide
Function to set front buzzer activation range
Narrow / Wide
Rear Buzzer Onset Range
Wide
Function to set rear buzzer activation range
Narrow / Wide
Keep Sense Status Buzzer
ON
Function to make buzzer sound when distance between vehicle and obstacle does not change for more than 3 seconds
ON / OFF
Fr & Rr Buzzer Volume
M2
Function to change volume of buzzer
L / M1 / M2 / M3 / H

Sensor 
DISPLAY
DEFAULT
CONTENTS
SETTING
Sensor Condition N Range
OFF
Function to make sensors available when shift position is N
OFF / ON
Sonar Mode
Steering
Function to change sonar mode
Normal / Steering

Display 
DISPLAY
DEFAULT
CONTENTS
SETTING
Sonar Display OFF Time
3 s
Function to change time until multi-information display turns off after sensors stop detecting obstacle
1 s / 2 s / 3 s / 4 s
Display Mode
Guide
Function to change display mode
All / Guide / Undisp

CUSTOMIZE MODE (MANUAL OPERATION METHOD)


  1. The settings shown below can be changed using customize mode. Enter customize mode by pressing and holding the clearance sonar main switch, and setting the light control switch from TAIL to OFF 3 times.

    Warning 
    CUSTOMIZE PARAMETERS
    		DEFAULT
    		CONTENTS
    		SETTING
    Front detection range
    		1,000 mm (39.37 in.)
    		Function to set a front detection range
    		500 mm (19.69 in.) / 1,000 mm (39.37 in.)
    Rear detection range
    		1,500 mm (59.06 in.)
    		Function to set a rear detection range
    		600 mm (23.62 in.) / 1,500 mm (59.06 in.)

    Sensor 
    CUSTOMIZE PARAMETERS
    		DEFAULT
    		CONTENTS
    		SETTING
    Sonar mode
    		Steering sensing mode
    		Function to change sonar mode
    		Normal clearance sonar mode / Steering sensing mode

    NOTICE:
    Check that the steering wheel is centered and the tires are aligned straightforward before changing to customize mode.


    E109433E01

    *1: Steering wheel is centered (tires aligned straightforward).
    *2: If 180 seconds pass, customize mode will end.
    *3: If a steering angle malfunction occurs, customize mode will proceed to {H} (customize mode ends).

    E109434E01


    Multi-information Display Indication Setting in Each Mode 

    		[1]
    		[2]
    		[3]
    		[4]
    		[5]
    		[6]
    		[7]
    		[8]
    		[9]
    		[10]
    		Note
    {A}
    		●
    		X
    		X
    		X
    		X
    		-
    		X
    		▲
    		▲
    		▲
    		[8], [9], [10] will illuminate if steering wheel mid-point is not set
    {B}
    		●
    ↓
    ○
    		X
    ↓
    ○
    		X
    		X
    ↓
    ○
    		X
    		-
    		X
    		●
    ↓
    ○
    		●
    ↓
    ○
    		●
    ↓
    ○
    		[1], [8] to [10] will illuminate for 2 seconds, then [1], [2], [4], [8] to [10] will flash
    {C}
    		○
    		○
    		X
    		○
    		X
    		-
    		X
    		X
    		X
    		X
    		[1], [2], [4] will flash
    {D}
    		○
    		X
    		X
    		X
    		X
    		-
    		X
    		X
    		X
    		X
    		[1] will flash
    {E}
    		○
    		○
    		X
    		X
    		▲
    		-
    		▲
    		X
    		X
    		X
    		[1], [2] will flash
    At the same time:
    If the front sensor detection area is set to 500 mm (19.69 in.), [5] will flash
    If the front sensor detection area is set to 1,000 mm (39.37 in.), [7] will flash
    {F}
    		○
    		X
    		○
    		X
    		▲
    		-
    		▲
    		X
    		X
    		X
    		[1], [3] will flash
    At the same time:
    If the rear sensor detection area is set to 600 mm (23.62 in.), [5] will flash
    If the rear sensor detection area is set to 1,500 mm (59.06 in.), [7] will flash
    {G}
    		○
    		X
    		X
    		○
    		▲
    		-
    		▲
    		X
    		X
    		X
    		[1], [4] will flash
    At the same time, if the steering sensing mode is set, [5] will flash
    If the normal mode is set, [7] will flash
    {H}
    		○
    		▲
    		▲
    		▲
    		▲
    		-
    		▲
    		X
    		X
    		X
    		{E}, {F} and {G} will flash their changed settings for 5 seconds
    {I}
    		●
    		●
    		●
    		●
    		●
    		-
    		●
    		●
    		●
    		●
    		All except [6] will illuminate for 2 seconds
    ●: Illumination
    ○: Flashing
    ▲: Flashes depending on condition
    X : No illumination or flashing