ROOF HEADLINING > REMOVAL

for Preparation Click here


HINT:
  1. The installation procedures are the removal procedures in reverse order. However, only installation procedures requiring additional information are included.
  1. A bolt without a torque specification is shown in the standard bolt chart.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



2. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY


B107406E01

  1. Remove the nut and shoulder anchor.



    B100934E02

  1. Disconnect the pretensioner connector as shown in the illustration labeled A.

  1. Disconnect the tension reducer connector labeled B.

  1. Disconnect the pre-crash safety connector labeled C.



    B107407

  1. Remove the 2 bolts and seat belt.



3. REMOVE FRONT SEAT ASSEMBLY


B105920E01

  1. Operate the power seat switch knob and move the seat to the rearmost position.

  1. Using a screwdriver, detach the 4 claws and remove the seat track bracket cover front inner and outer.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the 2 bolts on the front side of the seat.

  1. Operate the power seat switch knob and move the seat to the foremost position.



    B105921E01

  1. Using a screwdriver, detach the 4 claws and remove the seat track bracket cover rear inner and outer.

  1. Remove the 2 bolts on the rear side of the seat.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

  1. Disconnect the connectors under the seat. Then remove the seat.



4. REMOVE REAR SEAT CUSHION ASSEMBLY


B105946E01

  1. Detach the seat cushion's 2 front hooks from the vehicle body.

    NOTICE:
    Follow the instructions below carefully as the cushion frame deforms easily.


    1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

    2. Repeat for the other hook.

  1. Detach the seat cushion's 2 rear hooks from the seatback.

  1. Remove the seat cushion.



5. REMOVE REAR SEAT HEADREST ASSEMBLY LH

  1. Remove the headrest (Click here).



6. REMOVE REAR SEAT HEADREST ASSEMBLY RH

  1. Remove the headrest (Click here).



7. REMOVE REAR SEAT HEADREST ASSEMBLY CENTER

  1. Remove the headrest (Click here).



8. REMOVE REAR SEATBACK ASSEMBLY



B105947

  1. Using a screwdriver, detach the claws and remove the 2 rear seat covers.

    HINT:
    Tape the screwdriver tip before use.



    B105996E01

  1. Using a screwdriver, detach the claw to open the cap of the 3 rear seat shoulder belt guides.

  1. Remove the bolt and floor anchor part.



    B105948

  1. Remove the 4 bolts and 2 nuts.

  1. Remove the seatback.



9. REMOVE CONSOLE BOX

  1. Remove the console box (Click here).



10. REMOVE FRONT DOOR SCUFF PLATE LH


B111627E01

  1. Using a moulding remover, detach the 5 claws and remove the scuff plate.



11. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



12. REMOVE FRONT DOOR OPENING TRIM COVER LH

  1. Using a moulding remover, detach the 3 claws and remove the trim cover.



13. REMOVE FRONT DOOR OPENING TRIM COVER RH

HINT:
Use the same procedures described for the LH side.



14. REMOVE FRONT PILLAR GARNISH LH


B111628E01

  1. Detach the clip labeled A from the vehicle body. Pull the pillar garnish so that the tip of clip B locks in the pillar garnish's hole.

  1. Using needle-nose pliers, rotate clip B 90° and remove the pillar garnish.

    HINT:
    If clip B is removed from the vehicle body or is damaged, replace it with a new one.



    B108662E01

  1. Protect the curtain shield airbag.

    1. Thoroughly cover the airbag with a cloth or nylon sheet that is 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover with adhesive tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



15. REMOVE FRONT PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



16. REMOVE REAR DOOR SCUFF PLATE LH


B111629

  1. Detach the 5 claws and remove the scuff plate.



17. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



18. REMOVE CENTER PILLAR GARNISH LOWER LH


B111630

  1. Detach the 2 claws and 5 clips, and remove the garnish.



19. REMOVE CENTER PILLAR GARNISH LOWER RH

HINT:
Use the same procedures described for the LH side.



20. REMOVE CENTER PILLAR GARNISH LH


B111631E01

  1. Remove the 2 screws.

  1. Pull the garnish in the direction indicated by the arrow in the illustration to detach the claw. Then remove the garnish.



21. REMOVE CENTER PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



22. REMOVE REAR SEAT SIDE GARNISH LH


B111632

  1. Using a moulding remover, pull the garnish in the direction indicated by the arrow in the illustration to detach the 5 claws. Then remove the garnish.



23. REMOVE REAR SEAT SIDE GARNISH RH

HINT:
Use the same procedures described for the LH side.



24. REMOVE ROOF SIDE GARNISH INNER LH


B111633

  1. Detach the 4 clips.

  1. Pull the garnish in the direction indicated by the arrow in the illustration to detach the 2 claws. Then remove the garnish.



25. REMOVE ROOF SIDE GARNISH INNER RH

HINT:
Use the same procedures described for the LH side.



26. REMOVE REAR VIEW MIRROR COVER INNER


B108683E01

  1. Pull the cover in the direction indicated by the arrow in the illustration. Then remove the cover.



27. REMOVE FRONT ROOF TOP GARNISH


B111634E01

  1. w/ Rain sensor:
    Remove the top garnish.

    1. Using a screwdriver, detach the 3 claws and 2 clips, and remove the top garnish.

      HINT:
      Tape the screwdriver tip before use.

  1. w/o Rain sensor:
    Remove the top garnish.

    1. Using a screwdriver, detach the 3 claws and 2 clips, and remove the top garnish.

      HINT:
      Tape the screwdriver tip before use.



28. REMOVE PERSONAL LIGHT ASSEMBLY


B111635E01

  1. Using a screwdriver, remove the 2 covers and 2 screws.

  1. Using a moulding remover, detach the 2 clips and 3 claws.

  1. Disconnect the connector and remove the personal light.



29. REMOVE REAR VIEW MIRROR ASSEMBLY INNER


    E109862

  1. Remove the screw.



    E107999

  1. Disconnect the connector and remove the mirror.



30. REMOVE REAR ROOM LIGHT ASSEMBLY


B111636E01

  1. Using a screwdriver, detach the 4 claws and remove the rear room light from the vehicle body.

    HINT:
    Tape the screwdriver tip before use.

  1. Disconnect the connector from the room light.



31. REMOVE STEERING SPOT LIGHT ASSEMBLY

  1. Using a moulding remover, detach the 2 claws and remove the spot light.

  1. Disconnect the connector.



32. REMOVE ASSIST GRIP ASSEMBLY


    B111637E01

  1. w/o Sliding roof:
    Remove the assist grip.

    1. Using a screwdriver, detach the 6 claws and remove the 2 assist grip covers.

      HINT:
      Tape the screwdriver tip before use.



      2. B111638E01

    2. Detach the 2 claws in the order shown in the illustration.

      HINT:
      Repeat this for the other side and remove the assist grip.



    B111639E01

  1. w/ Sliding roof:
    Remove the assist grip.

    1. Using a screwdriver, detach the 6 claws and remove the 2 assist grip covers.

      HINT:
      Tape the screwdriver tip before use.



      2. B111640E01

    2. Detach the 2 claws in the order shown in the illustration.

      HINT:
      Repeat this for the other side and remove the assist grip.



33. REMOVE VISOR BRACKET COVER


    B111641E01

  1. Using a moulding remover, detach the 4 claws and remove the cover.



34. REMOVE VISOR ASSEMBLY LH

  1. Remove the 2 screws and visor.



35. REMOVE VISOR ASSEMBLY RH

  1. Remove the 2 screws and visor.



36. REMOVE VISOR HOLDER


    B050596

  1. Remove the visor holder by turning it counterclockwise.



37. REMOVE ROOF HEADLINING ASSEMBLY

  1. Disconnect the roof wire and connector from the front pillar.

  1. Detach the 4 clips labeled A and 12 clips labeled B.

  1. w/o Sliding roof:

    1. Detach the 2 hooks and fastener from the vehicle body side.



  1. w/ Sliding roof:

    1. Detach the hook and claw from the vehicle body side.

    2. Disconnect the connector from the drive gear.



    3. Detach the 4 clips labeled A and 12 clips labeled B, and 11 fasteners.


      B111642E01



    B108671

  1. Remove the roof headlining from the vehicle through the rear door, as shown in the illustration.

  1. Only when replacing the roof headlining:

    1. Remove the 11 fasteners from the roof headlining.



38. REMOVE VANITY LIGHT ASSEMBLY

  1. Using a screwdriver, detach the claws.

    HINT:
    Tape the screwdriver tip before use.

  1. Spread apart the detached claws and remove the bulb holder from the vanity light.



  1. Only when replacing the roof headlining:



      B111643

    1. Detach the claw and remove the vanity light.



39. REMOVE ROOF NO.1 WIRE

  1. Only when replacing the roof headlining:

    1. Remove the double-sided tape and roof wire.