LUGGAGE COMPARTMENT DOOR > INSTALLATION

for Preparation Click here


HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL LUGGAGE COMPARTMENT DOOR STRIKER ASSEMBLY


B109035

  1. Connect the connector.

  1. Install the striker with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



2. INSTALL LUGGAGE COMPARTMENT TRIM COVER INNER RH


B109033

  1. Install the trim cover with the 3 clips.

  1. Install the hook with the bolt.



3. INSTALL LUGGAGE COMPARTMENT TRIM COVER INNER LH


B109034

  1. Install the trim cover with the 3 clips.

  1. Install the hook with the bolt.



4. INSTALL LUGGAGE COMPARTMENT TRIM COVER FRONT


B107126E04

  1. Attach the 4 claws to install the trim cover.



    B110183

  1. Attach the hook.



    B110747

  1. Install the rope hook.



5. INSTALL REAR FLOOR FINISH PLATE


B107125E03

  1. Attach the 4 clips to install the finish plate.

  1. Install the 3 clips labeled A.

  1. Install the 2 hooks with the 2 bolts.



6. INSTALL TOOL BOX


B109030


7. INSTALL LUGGAGE NO. 1 COMPARTMENT LIGHT ASSEMBLY


B110753E01

  1. Connect the connector.

  1. Attach the claw to install the light.



8. INSTALL LUGGAGE COMPARTMENT FLOOR MAT


B109029


9. INSTALL LUGGAGE COMPARTMENT DOOR GARNISH SUB-ASSEMBLY


    B111353E06

  1. Attach the 7 clips to install the garnish.



    B109987

  1. Install the garnish with the 3 nuts.



10. INSTALL LICENSE PLATE LIGHT ASSEMBLY


B110162E03

  1. Install the license plate light and screw to the luggage compartment door..



    B110161

  1. Connect the connector.



11. INSTALL REAR LIGHT ASSEMBLY


B109917

  1. Install the gasket to the light.

  1. Install the light bulb to the light socket and wire.

  1. Install the light bulb socket and wire to the light.

  1. Install the light with the 3 nuts.

  1. Connect the connector.



12. INSTALL TELEVISION CAMERA ASSEMBLY


B107483E04

  1. Install the television camera with the 2 nuts.

  1. Attach the television camera connector clamp.

  1. Connect the television camera connector.



13. INSTALL LUGGAGE COMPARTMENT DOOR SUPPORT ASSEMBLY

  1. Install the 2 clips to the support.

  1. Install the support.



14. INSTALL REAR SPOILER SUB-ASSEMBLY

  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the double-sided tape from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.

  1. If reusing the spoiler:
    Clean the spoiler.

    1. Using a heat light, heat the spoiler.

    2. Remove the double-sided tape from the spoiler.

    3. Wipe off any tape adhesive residue with cleaner.

    4. Apply new double-sided tape to the spoiler.



  1. Install the spoiler.

    1. Using a heat light, heat the vehicle body and spoiler.

    2. Remove the peeling paper from the face of the spoiler.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.



      3. B107508E06

    3. Install the spoiler with the 4 nuts and clip.



15. INSTALL LUGGAGE DOOR OPENING SWITCH ASSEMBLY


B109023

  1. Install the opening switch with the 2 screws.



    B110161

  1. Connect the connector.



16. INSTALL LUGGAGE COMPARTMENT DOOR LOCK CYLINDER ASSEMBLY


B109024

  1. Connect the connector.

  1. Install the lock cylinder with the 2 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



17. INSTALL LUGGAGE DOOR CLOSER ASSEMBLY


B109027

  1. Connect the connector.

  1. Install the door closer with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



18. INSTALL LUGGAGE DOOR LOCK OPENER ASSEMBLY


B109026

  1. Install the door lock opener with the screw.



19. INSTALL LUGGAGE DOOR LOCK OPENER ASSEMBLY


B109022E01

  1. Install the cover with the 10 clips.



20. INSTALL DOOR INSIDE HANDLE BEZEL


B109020E01

  1. Attach the 4 claws to install the bezel.



21. INSTALL LUGGAGE COMPARTMENT DOOR ASSIST GRIP


B109021

  1. Install the assist grip with the 2 screws.



    B110748E01

  1. Attach the 4 claws to install the cover.