DTC    B1820/55    Short in Side Squib RH Circuit

DTC    B1821/55    Open in Side Squib RH Circuit

DTC    B1822/55    Short to GND in Side Squib RH Circuit

DTC    B1823/55    Short to B+ in Side Squib RH Circuit

for Preparation Click here


DESCRIPTION

The side squib RH circuit consists of the center airbag sensor assembly and the front seat airbag assembly RH.
This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the side squib RH circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1820/55
  1. The center airbag sensor assembly receives a line short circuit signal 5 times in the side squib RH circuit during primary check.
  2. Side squib RH malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Front seat airbag assembly RH (Side squib RH)
  3. Center airbag sensor assembly
B1821/55
  1. The center airbag sensor assembly receives an open circuit signal in the side squib RH circuit for 2 seconds.
  2. Side squib RH malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Front seat airbag assembly RH (Side squib RH)
  3. Center airbag sensor assembly
B1822/55
  1. The center airbag sensor assembly receives a short circuit to ground signal in the side squib RH circuit for 0.5 seconds.
  2. Side squib RH malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Front seat airbag assembly RH (Side squib RH)
  3. Center airbag sensor assembly
B1823/55
  1. The center airbag sensor assembly receives a short circuit to B+ signal in the side squib RH circuit for 0.5 seconds.
  2. Side squib RH malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Front seat airbag assembly RH (Side squib RH)
  3. Center airbag sensor assembly

WIRING DIAGRAM


H001454E24


INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting the "check mode" (signal check) with the intelligent tester (Click here).
  2. After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).

1.CHECK FRONT SEAT AIRBAG ASSEMBLY RH (SIDE SQUIB RH)


    C109502E02

  1. Turn the engine switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connector from the front seat airbag assembly RH.

  1. Connect the black wire side of SST (resistance 2.1 Ω) to connector "C".

    CAUTION:
    Never connect a tester to the front seat airbag assembly RH (Side squib RH) for measurement, as the may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert the SST into the terminals of the connector when connecting.
    2. Insert straight the SST into the terminals of the connector.

SST
09843-18060  

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the engine switch off.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1820, B1821, B1822, B1823 or 55 is not output.

    HINT:
    Codes other than DTC B1820, B1821, B1822, B1823 and 55 may be output at this time, but they are not related to this check.



OK
REPLACE FRONT SEAT AIRBAG ASSEMBLY RH
NG


2.CHECK FLOOR WIRE (SIDE SQUIB RH CIRCUIT)


    H044449E03

  1. Turn the engine switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the SST from connector "C".

  1. Disconnect the connectors from the center airbag sensor assembly.

  1. Check the short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Voltage:
      Tester connection
      		Condition
      		Specified condition
      V3-1 (SFR+) -
      Body ground
      		Engine switch on (IG)
      		Below 1 V
      V3-2 (SFR-) -
      Body ground
      		Engine switch on (IG)
      		Below 1 V

  1. Check the open in the circuit.

    1. Turn the engine switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Resistance:
      Tester connection
      		Condition
      		Specified condition
      V3-1 (SFR+) -
      V3-2 (SFR-)
      		Always
      		Below 1 Ω

  1. Check the short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Resistance:
      Tester connection
      		Condition
      		Specified condition
      V3-1 (SFR+) -
      Body ground
      		Always
      		1 MΩ or higher
      V3-2 (SFR-)
      Body ground
      		Always
      		1 MΩ or higher

  1. Check the short in the circuit.

    1. Release the activation prevention mechanism built into connector "B" (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Resistance:
      Tester connection
      		Condition
      		Specified condition
      V3-1 (SFR+) -
      V3-2 (SFR-)
      		Always
      		1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


3.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    H043390E01

  1. Connect the connectors to the front seat airbag assembly RH and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the engine switch off.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1820, B1821, B1822, B1823 or 55 is not output.

    HINT:
    Codes other than DTC B1820, B1821, B1822, B1823 and 55 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

USE SIMULATION METHOD TO CHECK