DTC    C2165/65    Abnormal Temperature Inside ID1 Tire

DTC    C2166/66    Abnormal Temperature Inside ID2 Tire

DTC    C2167/67    Abnormal Temperature Inside ID3 Tire

DTC    C2168/68    Abnormal Temperature Inside ID4 Tire

for Preparation Click here


DESCRIPTION

The tire pressure monitor valve sub-assembly measures tire internal temperature as well as tire pressure, and transmits the information to the tire pressure monitor receiver along with the transmitter ID. If the measured temperature is out of the specified range, the tire pressure monitor ECU recognizes it as a malfunction, outputs DTCs, and blinks the tire pressure warning light.

DTC No.
DTC Detecting Condition
Trouble Area
C2165/65
C2166/66
C2167/67
C2168/68
The temperature inside the tire is outside the range -40 to 215°C (-40 to 419°F).
  1. Tire pressure monitor valve sub-assembly
  2. Tire pressure monitor ECU
  3. Tire pressure monitor receiver assembly

HINT:
It is necessary to perform the procedure to identify the tire pressure monitor valve sub-assembly that is malfunctioning because it cannot be identified by the output DTC.


INSPECTION PROCEDURE

HINT:
Set the tire pressure to the specified value.

1.CHECK TIRE PRESSURE WARNING LIGHT

  1. Check the tire pressure warning light.


Result:

Proceed to
Condition
A
Does not blink
B
Comes on and goes off repeatedly at 0.5 second intervals



B
Go to step 8
A


2.IDENTIFY TRANSMITTER CORRESPONDING TO DTC

NEXT


3.CHECK TIRES

  1. Check the tire is not punctured, and there is no indication of air pressure drop.

    OK:
    Tire is normal.



NG
REPLACE TIRES
OK


4.ADJUST TIRE PRESSURE TO THE SPECIFIED VALUE

Tire Size
Front
kPa (kgf/cm2, psi)
Rear
kPa (kgf/cm2, psi)
For driving at speeds under 160 km/h (100 mph)
For driving at speeds of 160 km/h (100 mph) or over
For driving at speeds under 160 km/h (100 mph)
For driving at speeds of 160 km/h (100 mph) or over
245/40R 18
230 (2.3, 33)
260 (2.6. 38)
270 (2.7, 39)*
230 (2.3, 33)
260 (2.6. 38)*
270 (2.7, 39)
310 (3.1, 45)*
225/50R 17
230 (2.3, 33)
260 (2.6. 38)
270 (2.7, 39)*
230 (2.3, 33)
260 (2.6. 38)*
270 (2.7, 39)
320 (3.2, 46)*
*: When at least 4 people are in the vehicle.

NEXT


5.CLEAR DTC

NEXT


6.CHECK DTC

  1. Check for DTC (Click here).

    OK:
    DTC is not output.

    HINT:
    1. If the result is OK, replace the tire pressure monitor valve sub-assembly specified in STEP 2.
    2. Register the transmitter ID after replacement, and then set the tire pressure to the specified value.



NG
Go to step 13
OK

REPLACE TIRE PRESSURE MONITOR VALVE SUB-ASSEMBLY 

7.IDENTIFY TRANSMITTER CORRESPONDING TO DTC

NEXT


8.CHECK TIRES

  1. Check the tire is not punctured, and there is no indication of air pressure drop.

    OK:
    Tire is normal.



NG
REPLACE TIRES
OK


9.ADJUST TIRE PRESSURE TO THE SPECIFIED VALUE

Tire Size
Front
kPa (kgf/cm2, psi)
Rear
kPa (kgf/cm2, psi)
For driving at speeds under 160 km/h (100 mph)
For driving at speeds of 160 km/h (100 mph) or over
For driving at speeds under 160 km/h (100 mph)
For driving at speeds of 160 km/h (100 mph) or over
245/40R 18
230 (2.3, 33)
260 (2.6. 38)
270 (2.7, 39)*
230 (2.3, 33)
260 (2.6. 38)*
270 (2.7, 39)
310 (3.1, 45)*
225/50R 17
230 (2.3, 33)
260 (2.6. 38)
270 (2.7, 39)*
230 (2.3, 33)
260 (2.6. 38)*
270 (2.7, 39)
320 (3.2, 46)*
*: When at least 4 people are in the vehicle.

NEXT


10.REPLACE TIRE PRESSURE MONITOR VALVE SUB-ASSEMBLY

  1. Replace the identified tire pressure monitor valve sub-assembly with a new one (Click here).


NEXT


11.REGISTRATION OF TRANSMITTER ID

  1. Register the transmitter ID for 4 wheels.

  1. Set the tire pressure to the specified value.


NEXT


12.CHECK DTC

  1. Check for DTC.

    OK:
    DTC is not output.



NG
Go to step 13
OK

END 

13.REPLACE TIRE PRESSURE MONITOR RECEIVER ASSEMBLY

HINT:
Perform the inspection using parts from a normal vehicle when possible.


NEXT


14.CHECK DTC

  1. Check for DTC.

    OK:
    DTC is not output.



NG
REPLACE TIRE PRESSURE MONITOR ECU
OK

END