REAR SUNSHADE ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL REAR SUNSHADE RELAY

  1. Install the relay with the 2 screws.

  1. Connect the connector.

  1. Attach the claw to install the relay cover.



2. INSTALL REAR WINDOW SUNSHADE ASSEMBLY


B108848E01

  1. Tighten the bolt labeled A.

  1. Install the window shade with the 5 bolts.



3. INSTALL NO.2 PACKAGE TRAY TRIM PANEL ASSEMBLY


B111649

  1. Connect the connector.

  1. Attach the 5 claws and 3 clips to install the panel.



4. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY


B112274

  1. Attach the clip to install the package tray trim panel.

  1. Attach the 4 claws to install the belt guide center.



    B100960E06

  1. Attach the 4 claws to install the belt guide LH.



5. INSTALL AUTOMATIC LIGHT CONTROL SENSOR

  1. Connect the connector and install the sensor.



6. INSTALL HIGH MOUNTED STOP LIGHT ASSEMBLY

  1. Install the high mounted stop light.



7. INSTALL ROOF SIDE GARNISH INNER LH

  1. Attach the 2 claws and 4 clips, and install the garnish.



8. INSTALL ROOF SIDE GARNISH INNER RH

HINT:
Use the same procedures described for the LH side.



9. INSTALL REAR SEAT SIDE GARNISH LH


B111645E01

  1. Attach the 5 claws and install the garnish.

  1. Pull out the folded lip of the weatherstrip.



10. INSTALL REAR SEAT SIDE GARNISH RH

HINT:
Use the same procedures described for the LH side.



11. INSTALL REAR DOOR SCUFF PLATE LH


B111646E01

  1. Attach the 5 claws to install the scuff plate.

  1. Pull out the folded lip of the weatherstrip.



12. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



13. INSTALL REAR SEATBACK ASSEMBLY


B105948

  1. Place the seatback in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Install the seatback with the 4 bolts and 2 nuts.

    Torque:
    18.1 N*m{ 185 kgf*cm , 13 ft.*lbf }

  1. Install the 2 rear seat covers.

  1. Pass the 3 seat belts through and close the cap of the 3 rear seat shoulder belt guides.

  1. Install the floor anchor part with the bolt.



14. INSTALL REAR SEAT HEADREST ASSEMBLY CENTER

  1. Install the headrest (Click here).



15. INSTALL REAR SEAT HEADREST ASSEMBLY LH

  1. Install the headrest (Click here).



16. INSTALL REAR SEAT HEADREST ASSEMBLY RH

  1. Install the headrest (Click here).



17. INSTALL REAR SEAT CUSHION ASSEMBLY


B105948

  1. Place the seatback in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Install the seatback with the 4 bolts and 2 nuts.

    Torque:
    18.1 N*m{ 185 kgf*cm , 13 ft.*lbf }

  1. Install the 2 rear seat covers.

  1. Pass the 3 seat belts through and close the cap of the 3 rear seat shoulder belt guides.

  1. Install the floor anchor part with the bolt.



18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


19. PERFORM INITIALIZATION

  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.