POWER WINDOW CONTROL SYSTEM > ON-VEHICLE INSPECTION

for Preparation Click here



1. CHECK WINDOW LOCK SWITCH


B108115

  1. Check that the passenger side power window and rear power windows are disabled when the window lock switch of the multiplex network master switch is pressed.

  1. Check that the passenger side power window and rear power windows can be operated when the window lock switch is pressed again.



2. CHECK MANUAL UP/DOWN FUNCTION

  1. Check that the driver side power window operates as follows:

    OK: 
    Condition
    		Master Switch
    		Switch Operation
    		Power Window
    Engine switch on (IG)
    		Driver side
    		Pulled halfway up
    		UP (closes)
    Engine switch on (IG)
    		Driver side
    		Pushed halfway down
    		DOWN (opens)

  1. Check that the power windows, except the driver side power window, operate as follows:

    OK: 
    Condition
    		Master Switch
    		Switch Operation
    		Power Window
    1. Engine switch on (IG)
    2. Window lock switch OFF
    		Front passenger side
    		Pulled halfway up
    		UP (closes)
    1. Engine switch on (IG)
    2. Window lock switch OFF
    		Front passenger side
    		Pushed halfway down
    		DOWN (opens)
    1. Engine switch on (IG)
    2. Window lock switch OFF
    		Rear LH
    		Pulled halfway up
    		UP (closes)
    1. Engine switch on (IG)
    2. Window lock switch OFF
    		Rear LH
    		Pushed halfway down
    		DOWN (opens)
    1. Engine switch on (IG)
    2. Window lock switch OFF
    		Rear RH
    		Pulled halfway up
    		UP (closes)
    1. Engine switch on (IG)
    2. Window lock switch OFF
    		Rear RH
    		Pushed halfway down
    		DOWN (opens)



3. CHECK AUTO UP/DOWN FUNCTION

  1. Check that the driver side power window operates as follows:

    OK: 
    Condition
    		Master Switch
    		Switch Operation
    		Power Window
    Engine switch on (IG)
    		Driver side
    		Pulled halfway up
    		AUTO UP (fully closes)
    Engine switch on (IG)
    		Driver side
    		Pushed halfway down
    		AUTO DOWN (fully opens)

  1. Check that the power windows, except the driver side power window, operate as follows:

    OK: 
    Condition
    		Each Switch
    		Switch Operation
    		Power Window
    1. Engine switch on (IG)
    2. Window lock switch OFF
    		Front passenger side
    		Pulled fully up
    		AUTO UP (fully closes)
    1. Engine switch on (IG)
    2. Window lock switch OFF
    		Front passenger side
    		Pushed fully down
    		AUTO DOWN (fully opens)
    1. Engine switch on (IG)
    2. Window lock switch OFF
    		Rear LH
    		Pulled fully up
    		AUTO UP (fully closes)
    1. Engine switch on (IG)
    2. Window lock switch OFF
    		Rear LH
    		Pushed fully down
    		AUTO DOWN (fully opens)
    1. Engine switch on (IG)
    2. Window lock switch OFF
    		Rear RH
    		Pulled fully up
    		AUTO UP (fully closes)
    1. Engine switch on (IG)
    2. Window lock switch OFF
    		Rear RH
    		Pushed fully down
    		AUTO DOWN (fully opens)



4. CHECK REMOTE MANUAL UP/DOWN FUNCTION

  1. Check that the power windows, except the driver side power window, operate as follows:

    OK: 
    Condition
    		Master Switch
    		Switch Operation
    		Power Window
    1. Engine switch on (IG)
    2. Window lock switch OFF
    		Front passenger side
    		Pulled halfway up
    		UP (closes)
    1. Engine switch on (IG)
    2. Window lock switch OFF
    		Front passenger side
    		Pushed halfway down
    		DOWN (opens)
    1. Engine switch on (IG)
    2. Window lock switch OFF
    		Rear LH
    		Pulled halfway up
    		UP (closes)
    1. Engine switch on (IG)
    2. Window lock switch OFF
    		Rear LH
    		Pushed halfway down
    		DOWN (opens)
    1. Engine switch on (IG)
    2. Window lock switch OFF
    		Rear RH
    		Pulled halfway up
    		UP (closes)
    1. Engine switch on (IG)
    2. Window lock switch OFF
    		Rear RH
    		Pushed halfway down
    		DOWN (opens)



5. CHECK REMOTE UP/DOWN FUNCTION

  1. Check that the power windows, except the driver side power window, operate as follows:

    OK: 
    Condition
    		Master Switch
    		Switch Operation
    		Power Window
    1. Engine switch on (IG)
    2. Window lock switch OFF
    		Front passenger side
    		Pulled fully up
    		AUTO UP (fully closes)
    1. Engine switch on (IG)
    2. Window lock switch OFF
    		Front passenger side
    		Pushed fully down
    		AUTO DOWN (fully opens)
    1. Engine switch on (IG)
    2. Window lock switch OFF
    		Rear LH
    		Pulled fully up
    		AUTO UP (fully closes)
    1. Engine switch on (IG)
    2. Window lock switch OFF
    		Rear LH
    		Pushed fully down
    		AUTO DOWN (fully opens)
    1. Engine switch on (IG)
    2. Window lock switch OFF
    		Rear RH
    		Pulled fully up
    		AUTO UP (fully closes)
    1. Engine switch on (IG)
    2. Window lock switch OFF
    		Rear RH
    		Pushed fully down
    		AUTO DOWN (fully opens)



6. CHECK JAM PROTECTION FUNCTION


B108116E02

HINT:
The jam protection function helps prevent any parts of your body from being caught by accident between the door frame and door glass during power window operation.

NOTICE:
If the power window motor has just been reset, raise and lower the door glass several times manually before performing the check.

  1. Check that the door glass moves down approximately 50 mm (1.97 in.) immediately if something gets caught between the door frame and door glass during power window operation. However, when the opening between the door frame and the door glass is less than 200 mm (7.87 in.), the door glass continues to go down and does not stop until an opening of 200 mm (7.87 in.) is achieved.
    Operative conditions:

    1. AUTO UP (ALL DOORS)
    2. AUTO UP/MANUAL UP function after the engine switch is turned off (ALL DOORS)
    3. MANUAL UP function using the driver side door key cylinder
    4. MANUAL UP function using the lock switch on the key*
    5. MANUAL UP function using entry lock switch on the outside door handle of the driver side door*

    HINT:
    *: Except Australia



7. CHECK PTC OPERATION

HINT:
PTC operation is a function that prevents overloading of the power window regulator by stopping the motor.
PTC operation activates when the power window regulator switch is operated for a predetermined amount of time.

  1. Pull up and hold a power window switch for more than 90 seconds. Release the switch.

  1. Check that pressing the switch does not move the window.

  1. Wait until 60 seconds have passed since the switch was released in the first step above. Check that pressing the switch results in normal window movement.



8. CHECK MANUAL UP/DOWN FUNCTION USING DRIVER SIDE DOOR LOCK KEY CYLINDER

  1. Check that all of power windows and the sliding roof operate as follows.

    OK: 
    Condition
    		Key Operation
    		Location/Operation
    No key is inside vehicle
    All doors closed and locked
    		Turned left (LOCK) for more than 1.5 sec.
    		Driver and passenger side power windows/UP
    No key is inside vehicle
    All doors closed and locked
    		Turned left (LOCK) for more than 2.3 sec.
    		Rear LH and RH power windows/UP
    No key is inside vehicle
    All doors closed and locked
    		Turned left (LOCK) for more than 2.5 sec.
    		Sliding roof/CLOSED
    No key is inside vehicle
    All doors closed and locked
    		Turned right (UNLOCK) for more than 1.5 sec.
    		Driver and passenger side power windows/DOWN
    No key is inside vehicle
    All doors closed and locked
    		Turned right (UNLOCK) for more than 2.3 sec.
    		Rear LH and RH power windows/DOWN
    No key is inside vehicle
    All doors closed and locked
    		Turned right (UNLOCK) for more than 2.5 sec.
    		Sliding roof/OPEN



9. CHECK MANUAL UP/DOWN FUNCTION USING KEY

  1. Check that all of power windows and the sliding roof operate as follows when operating the transmitter.

    OK: 
    Condition
    		Transmitter Operation
    		Location/Operation
    No key is inside vehicle
    All doors closed and locked
    		UNLOCK switch pressed for more than 2.5 sec.
    		Driver and passenger side power windows/DOWN
    No key is inside vehicle
    All doors closed and locked
    		UNLOCK switch pressed for more than 2.3 sec.
    		Rear LH and RH power windows/DOWN
    No key is inside vehicle
    All doors closed and locked
    		UNLOCK switch pressed for more than 3.5 sec.
    		Sliding roof/OPEN
    No key is inside vehicle
    All doors closed and locked
    		LOCK switch pressed for more than 2.5 sec.
    		Driver and passenger side power windows/UP
    No key is inside vehicle
    All doors closed and locked
    		LOCK switch pressed for more than 2.3 sec.
    		Rear LH and RH power windows/UP
    No key is inside vehicle
    All doors closed and locked
    		LOCK switch pressed for more than 3.5 sec.
    		Sliding roof/CLOSE

    HINT:
    1. As a sign for starting operation, the wireless door lock buzzer sounds once (answer-back).
    2. MANUAL UP function using key is not available for Australian models.



10. CHECK MANUAL UP FUNCTION USING ENTRY LOCK SWITCH (EXCEPT AUSTRALIA)

  1. Check that all of power windows and the slide roof operate as follows when the entry lock switch is pressed and held.

    OK: 
    Condition
    		Transmitter Operation
    		Location/Operation
    No key is inside vehicle
    All doors closed
    		Entry lock switch pressed for more than 3 sec.
    		Driver and passenger side power windows/UP
    No key is inside vehicle
    All doors closed
    		Entry lock switch pressed for more than 3 sec.
    		Rear LH and RH power windows/UP
    No key is inside vehicle
    All doors closed
    		Entry lock switch pressed for more than 3 sec.
    		Sliding roof/CLOSE

    HINT:
    1. As a sign for starting operation, the wireless door lock buzzer sounds once (answer-back).



11. CHECK POWER WINDOW OPERATION FUNCTION AFTER ENGINE SWITCH IS TURNED OFF

  1. When the following condition is fulfilled, check that the power windows can be operated even after the engine switch is turned off.

    1. All doors are closed for 43 seconds after the engine switch is turned off.