POWER MIRROR CONTROL SYSTEM > Driver Side Power Mirror cannot be Adjusted with Power Mirror Switch

for Preparation Click here


SYSTEM DESCRIPTION

This circuit detects the conditions of the mirror control switch.
The integration control and panel assembly sends information about the operating condition of the mirror switch (switch input signals) through the BEAN line. Then the switch input signals are sent to the front multiplex network door ECU (driver side). Mirror adjustment is controlled by the front multiplex network door ECU (driver side).

WIRING DIAGRAM


B111128E01


INSPECTION PROCEDURE

1.CHECK POWER MIRROR CONTROL FUNCTION

  1. Using the outer mirror switch, check if the driver side power mirror can be adjusted. Using the retract switch, check if the driver side power mirror can be retracted and returned.

    Result:

    Result
    		Proceed to
    Unable to adjust driver side power mirror
    		A
    Unable to retract / return driver side power mirror
    		B
    Unable to adjust and retract / return driver side power mirror
    		C



B
GO TO PROBLEM SYMPTOMS TABLE

C
Go to step 5
A


2.READ VALUE OF INTELLIGENT TESTER (MIRROR MASTER SWITCH AND MIRROR CONTROL SWITCH)

  1. Check the Data List for proper functioning of the mirror master switch and mirror control switch.

    Integration control and panel assembly:
    LHD:

    Item
    		Measurement Item / Display (Range)
    		Normal Condition
    		Diagnostic Note
    Mirror Selection SW (L)
    		Mirror master switch signal for LH mirror / ON or OFF
    		ON: Switch is in L position
    OFF: Switch is OFF or in R position
    		-
    Mirror Position SW (R)
    		Mirror control switch signal (Right) / ON or OFF
    		ON: RIGHT switch is ON
    OFF: Any switch except RIGHT is ON or all switches are OFF
    		-
    Mirror Position SW (L)
    		Mirror control switch signal (Left) / ON or OFF
    		ON: LEFT switch is ON
    OFF: Any switch except LEFT is ON or all switches are OFF
    		-
    Mirror Position SW (Up)
    		Mirror control switch signal (Up) / ON or OFF
    		ON: UP switch is ON
    OFF: Any switch except UP is ON or all switches are OFF
    		-
    Mirror Position SW (Dwn)
    		Mirror control switch signal (DOWN) / ON or OFF
    		ON: DOWN switch is ON
    OFF: Any switch except DOWN is ON or all switches are OFF
    		-
    RHD:

    Item
    		Measurement Item / Display (Range)
    		Normal Condition
    		Diagnostic Note
    Mirror Selection SW (R)
    		Mirror master switch signal for RH mirror / ON or OFF
    		ON: Switch is in R position
    OFF: Switch is OFF or in L position
    		-
    Mirror Position SW (R)
    		Mirror control switch signal (Right) / ON or OFF
    		ON: RIGHT switch is ON
    OFF: Any switch except RIGHT is ON or all switches are OFF
    		-
    Mirror Position SW (L)
    		Mirror control switch signal (Left) / ON or OFF
    		ON: LEFT switch is ON
    OFF: Any switch except LEFT is ON or all switches are OFF
    		-
    Mirror Position SW (Up)
    		Mirror control switch signal (Up) / ON or OFF
    		ON: UP switch is ON
    OFF: Any switch except UP is ON or all switches are OFF
    		-
    Mirror Position SW (Dwn)
    		Mirror control switch signal (DOWN) / ON or OFF
    		ON: DOWN switch is ON
    OFF: Any switch except DOWN is ON or all switches are OFF
    		-

    OK:
    On tester screen, each item changes between ON and OFF according to above chart.



NG
REPLACE INTEGRATION CONTROL AND PANEL ASSEMBLY
OK


3.PERFORM ACTIVE TEST BY INTELLIGENT TESTER (POWER MIRROR CONTROL FUNCTION)

  1. Select the Active Test, use the intelligent tester to generate a control command, and then check the power mirror control function.

    Front multiplex network door ECU (driver side):

    Item
    		Test Details
    		Diagnostic Note
    Mirror Up / Down
    		Mirror vertical operation UP / DOWN
    		-
    Mirror Right / Left
    		Mirror horizontal operation RIGHT / LEFT
    		-


    Result:

    Result
    		Proceed to
    Driver side outer rear view mirror does not operate normally
    		A
    Driver side outer rear view mirror operates normally
    		B



B
REPLACE FRONT MULTIPLEX NETWORK DOOR ECU (DRIVER SIDE)
A


4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER SIDE) (LEFT / RIGHT MOTOR, UP / DOWN MOTOR)
B111137E01

  1. Remove the driver side mirror.

  1. Apply battery voltage and check the operation of the power mirror.

    OK:
    Measurement Condition
    		Specified Condition
    Battery positive (+) → Terminal 1 (MV)
    Battery negative (-) → Terminal 10 (M+)
    		Turns upward (A)
    Battery negative (-) → Terminal 1 (MV)
    Battery positive (+) → Terminal 10 (M+)
    		Turns downward (B)
    Battery positive (+) → Terminal 9 (MH)
    Battery negative (-) → Terminal 10 (M+)
    		Turns left (C)
    Battery negative (-) → Terminal 9 (MH)
    Battery positive (+) → Terminal 10 (M+)
    		Turns right (D)



NG
REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER SIDE)
OK

REPLACE FRONT MULTIPLEX NETWORK DOOR ECU (DRIVER SIDE) 

5.INSPECT FUSE (FR DOOR LH, FR DOOR RH)

  1. LHD:

    1. Remove the FR DOOR LH fuse from the cowl side junction block LH.
    RHD:
    1. Remove the FR DOOR RH fuse from the cowl side junction block RH .

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


6.CHECK WIRE HARNESS (FRONT MULTIPLEX NETWORK DOOR ECU (DRIVER SIDE) - BATTERY AND BODY GROUND)
B109877E06

  1. Disconnect the O3 or N4 ECU connector.

  1. Measure the voltage and resistance of the wire harness side connector.

    Standard voltage:
    LHD:
    Tester Connection
    		Specified Condition
    O3-6 (BDR) - Body ground
    		10 to 14 V
    RHD:
    Tester Connection
    		Specified Condition
    N4-6 (BDR) - Body ground
    		10 to 14 V


    Standard resistance:
    LHD:
    Tester Connection
    		Specified Condition
    O3-1 (GND) - Body ground
    		Below 1 Ω
    RHD:
    Tester Connection
    		Specified Condition
    N4-1 (GND) - Body ground
    		Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE FRONT MULTIPLEX NETWORK DOOR ECU (DRIVER SIDE)