DTC    B1610/13    Front Airbag Sensor RH Circuit Malfunction

for Preparation Click here


DESCRIPTION

The front airbag sensor RH consists of the diagnostic circuit, the frontal deceleration sensor, etc.
If the center airbag sensor assembly receives signals from the frontal deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1610/13 is recorded when a malfunction is detected in the front airbag sensor RH circuit.

DTC No.
DTC Detecting Condition
Trouble Area
B1610/13
  1. The center airbag sensor assembly receives an open circuit signal in the front airbag sensor RH circuit for 2 seconds.
  2. Front airbag sensor RH malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Engine room main wire
  3. Front airbag sensor RH
  4. Center airbag sensor assembly

WIRING DIAGRAM


H016901E04


INSPECTION PROCEDURE

1.CHECK DTC


    H043400E01

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the engine switch off.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1610/13 is not output.

    HINT:
    Codes other than DTC B1610/13 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


2.CHECK CONNECTION OF CONNECTORS

  1. Turn the engine switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor RH.

    OK:
    The connectors are connected.



NG
CONNECT CONNECTORS, THEN GO TO STEP 1
OK


3.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (OPEN)


    C107450E02

  1. Disconnect the connectors from the center airbag sensor assembly and the front airbag sensor RH.

  1. Using a service wire, connect L44-29 (+SR) and L44-27 (-SR) of connector "B".

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    		Condition
    		Specified condition
    A25-2 (+SR) -
    A25-1 (-SR)
    		Always
    		Below 1 Ω



NG
Go to step 5
OK


4.CHECK FRONT AIRBAG SENSOR RH


    H043401E01

  1. Disconnect the service wire from connector "B".

  1. Connect the connectors to the center airbag sensor assembly.

  1. Interchange the front airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the engine switch off.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    Result:
    Result
    		Proceed to
    DTC B1610/13 is output.
    		A
    DTC B1615/14 is output.
    		B
    DTC B1610/13 and B1615/14 are not output.
    		C

    HINT:
    Codes other than DTC B1610/13 and B1615/14 may be output at this time, but they are not related to this check.



A
REPLACE CENTER AIRBAG SENSOR ASSEMBLY

B
REPLACE FRONT AIRBAG SENSOR RH
C

USE SIMULATION METHOD TO CHECK 

5.CHECK ENGINE ROOM MAIN WIRE (OPEN)


    C107451E03

  1. Disconnect the service wire from connector "B".

  1. Disconnect the engine room main wire connector from the instrument panel wire.

  1. Using a service wire, connect LA4-2 (+SR) and LA4-1 (-SR) of connector "D".

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    		Condition
    		Specified condition
    A25-2 (+SR) -
    A25-1 (-SR)
    		Always
    		Below 1 Ω



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE