DTC    B1653/35    Seat Position Airbag Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The seat position airbag sensor circuit consists of the center airbag sensor assembly and the seat position airbag sensor.
DTC B1653/35 is recorded when a malfunction is detected in the seat position airbag sensor circuit.

DTC No.
DTC Detecting Condition
Trouble Area
B1653/35
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat position airbag sensor circuit for 2 seconds.
  2. Seat position airbag sensor malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire No.2 (LHD)
  2. Floor wire (RHD)
  3. Seat position airbag sensor
  4. Center airbag sensor assembly

WIRING DIAGRAM


C111943E05


INSPECTION PROCEDURE

1.CHECK DTC


    C111950E01

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the engine switch off.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


2.CHECK CONNECTION OF CONNECTORS

  1. Turn the engine switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the seat position airbag sensor.

    OK:
    The connectors are connected.



NG
CONNECT CONNECTORS, THEN GO TO STEP 1
OK


3.CHECK VEHICLE STEERING POSITION

  1. Confirm that the vehicle steering position.

    Result:

    Result
    		Proceed to
    LHD
    		A
    RHD
    		B



B
Go to step 8
A


4.CHECK FLOOR WIRE NO.2 (OPEN)


    C109491E03

  1. Disconnect the connectors from the center airbag sensor assembly and the seat position airbag sensor.

  1. Using a service wire, connect W16-16 (LSP+) and W16-24 (LSP-) of connector "B".

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    		Condition
    		Specified condition
    W4-2 (LSP+) -
    W4-4 (LSP-)
    		Always
    		Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE NO.2
OK


5.CHECK FLOOR WIRE NO.2 (SHORT)


    C109492E04

  1. Disconnect the service wire from connector "B".

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    		Condition
    		Specified condition
    W4-2 (LSP+) -
    W4-4 (LSP-)
    		Always
    		1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE NO.2
OK


6.CHECK FLOOR WIRE NO.2 (SHORT TO B+)


    C109492E04

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Voltage:
    Tester connection
    		Condition
    		Specified condition
    W4-2 (LSP+) -
    Body ground
    		Engine switch on (IG)
    		Below 1 V
    W4-4 (LSP-) -
    Body ground
    		Engine switch on (IG)
    		Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE NO.2
OK


7.CHECK FLOOR WIRE NO.2 (SHORT TO GROUND)


    C109492E04

  1. Turn the engine switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    		Condition
    		Specified condition
    W4-2 (LSP+) -
    Body ground
    		Always
    		1 MΩ or higher
    W4-4 (LSP-) -
    Body ground
    		Always
    		1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE NO.2
OK

GO TO STEP 12 

8.CHECK FLOOR WIRE (OPEN)


    C109487E03

  1. Disconnect the connectors from the center airbag sensor assembly and the seat position airbag sensor.

  1. Using a service wire, connect V13-9 (RSP+) and V13-17 (RSP-) of connector "B".

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    		Condition
    		Specified condition
    V39-2 (RSP+) -
    V39-4 (RSP-)
    		Always
    		Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE
OK


9.CHECK FLOOR WIRE (SHORT)


    C109488E04

  1. Disconnect the service wire from connector "B".

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    		Condition
    		Specified condition
    V39-2 (RSP+) -
    V39-4 (RSP-)
    		Always
    		1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


10.CHECK FLOOR WIRE (SHORT TO B+)


    C109488E04

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Voltage:
    Tester connection
    		Condition
    		Specified condition
    V39-2 (RSP+) -
    Body ground
    		Engine switch on (IG)
    		Below 1 V
    V39-4 (RSP-) -
    Body ground
    		Engine switch on (IG)
    		Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE
OK


11.CHECK FLOOR WIRE (SHORT TO GROUND)


    C109488E04

  1. Turn the engine switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    		Condition
    		Specified condition
    V39-2 (RSP+) -
    Body ground
    		Always
    		1 MΩ or higher
    V39-4 (RSP-) -
    Body ground
    		Always
    		1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


12.CHECK SEAT POSITION AIRBAG SENSOR


    C111950E01

  1. Connect the connectors to the center airbag sensor assembly and the seat position airbag sensor.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the engine switch off.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


13.REPLACE SEAT POSITION AIRBAG SENSOR

  1. Turn the engine switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the seat position airbag sensor (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.


NEXT


14.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    C111950E01

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the engine switch off.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

END