ELECTRONIC POWER STEERING SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
By accessing the data list displayed on the intelligent tester, you can perform such functions as reading the values of switches and sensors without removing any parts. Reading the data list is the first step of troubleshooting and is one method to shorten labor time.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Operate the intelligent tester according to the steps on the display and select data list.

    Item
    		Item Description/Range (Display)
    		Inspection Condition
    		Reference Value
    Torque Sensor 1 Output
    		Torque sensor 1 rotation angle/
    Min.: 0 deg, Max.: 360 deg
    		Steering wheel is turned
    		Value changes from 0 to 360° every 22.5° of steering angle
    Torque Sensor 2 Output
    		Torque sensor 2 rotation angle/
    Min.: 0 deg, Max.: 360 deg
    		Steering wheel is turned
    		Value changes from 0 to 360° every 22.5° of steering angle
    Meter Vehicle Velocity
    		Vehicle speed from meter/
    Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    1. Vehicle is stopped
    2. Vehicle is driven at a constant speed
    1. 0 km/h (0 mph)
    2. No significant fluctuation
    Engine Revolution
    		Engine revolution/Min.: 0 rpm,
    Max.: 8192 rpm
    		Engine is running at a constant speed
    		No significant fluctuation
    Motor Actual Current
    		Amount of current to motor/
    Min.: -128 A, Max.: 127 A
    		Power steering is in operation
    		Value changes in proportion to steering effort
    Command Value Current
    		Demanded amount of current to motor/
    Min.: -128 A, Max.: 127 A
    		Power steering is in operation
    		Value changes in proportion to steering effort
    Steering Angle Velocity
    		Steering angle speed/Min.: -4096
    deg/sec, Max.: 4064 deg/sec
    		Steering wheel is turned
    		Value changes in proportion to steering speed
    Thermistor Temperature
    		ECU substrate temperature/
    Min.: -50 °C, Max.: 205°C
    		Engine switch on (IG)
    		-
    PIG Power Supply
    		Power source voltage to activate motor/
    Min.: 0 V, Max.: 25.5 V
    		Power steering is in operation
    		10 to 14 V
    IG Power Supply
    		ECU power source voltage/
    Min.: 0 V, Max.: 25.5 V
    		Engine switch on (IG)
    		10 to 14 V
    TRQ1 Zero Point Value
    		Zero point value of torque sensor 1/
    Min.: 0 deg, Max.: 360 deg
    		Steering wheel is not turned
    (without load)
    		Values differ depending on vehicle
    TRQ2 Zero Point Value
    		Zero point value of torque sensor 2/
    Min.: 0 deg, Max.: 360 deg
    		Steering wheel is not turned
    (without load)
    		Values differ depending on vehicle
    Steering Wheel Torque
    		Steering torque/Min.: -7.0 N*m,
    Max.: 7.0 N*m
    		Steering wheel is turned
    		Value changes in proportion to steering effort
    Motor Rotation Angle
    		Motor rotation angle/Min.: 0 deg,
    Max.: 360 deg
    		Steering wheel is turned
    		Value changes from 0 to 360° every 22.5° of steering angle
    Command Val Current 2
    		Amount of current demanded by motor 2/
    Min.: -128 A, Max.: 127 A
    		-
    		-
    PIG2 Voltage
    		Motor drive voltage after pressurization
    		Power steering is in operation
    		27 to 34 V
    Motor Voltage
    		Motor power source voltage/Min.:
    0 V, Max.: 64 V
    		Power steering is in operation
    		27 to 34 V
    Motor Terminal Volt(U)
    		Motor terminal voltage (U phase)/
    Min.: 0 V, Max.: 64 V
    		Power steering is in operation
    		27 to 34 V
    Motor Terminal Volt(V)
    		Motor terminal voltage (V phase)/
    Min.: 0 V, Max.: 64 V
    		Power steering is in operation
    		27 to 34 V
    Motor Terminal Volt(W)
    		Motor terminal voltage (W phase)/
    Min.: 0 V, Max.: 64 V
    		Power steering is in operation
    		27 to 34 V
    Steering Angle Sens Sig
    		Steering angle sensor signal status/
    OK or NG
    		-
    		-
    Motor Overheat Record
    		Continuous overheat prevention control record/
    Rec or Unrec
    		-
    		-
    Motor Lo Power Record
    		PIG power source voltage drop record/
    Rec or Unrec
    		-
    		-
    Eng Rev Inter Record
    		Record of engine revolution signal
    interruption/Rec or Unrec
    		-
    		-
    Str Angle Inter Record
    		Record of steering angle sensor
    signal interruption/Rec or Unrec
    		-
    		-
    Spd Sig Invalid Record
    		Record of vehicle speed signal invalid/
    Rec or Unrec
    		-
    		-
    Control Mode
    		Codes indicating DTC detection timing during ECU control are displayed in hexadecimal
    		-
    		-
    IG ON/OFF Times
    		Number of times IG switch is turned on after DTC detection/
    Min.: 0 time, Max.: 255 times
    		-
    		-
    The Number of DTCs
    		Number of detected DTCs when freeze frame data is stored/
    Min.: 0, Max.: 255
    		-
    		-
    Assist Map Select State
    		Selected assist map/01 to 09,11 or 12
    		-
    		-
    ECU Identification
    		ECU identification information/01 to 09, 11or 12
    		-
    		-
    Test Mode Status
    		Selected mode/
    Normal or Test
    		-
    		-