ENGINE ASSEMBLY
Part Tightened
| N*m
| kgf*cm
| ft.*lbf
|
Air cleaner assembly with hose x Body
| 5.0
| 51
| 44 in.*lbf
|
Air cleaner inlet No. 1 x Body
| 5.0
| 51
| 44 in.*lbf
|
V-bank cover x Engine assembly
| 5.0
| 51
| 44 in.*lbf
|
Pulley compressor assembly x Engine assembly
| 25
| 255
| 18
|
Front exhaust pipe assembly x exhaust manifold
| 62
| 632
| 46
|
Exhaust pipe No. 1 support bracket sub-assembly x exhaust manifold
| for Nut
| 62
| 632
| 46
|
for Bolt
| 43
| 438
| 22
|
Front No. 1 floor heat insulator
| 5.0
| 51
| 44 in.*lbf
|
Front floor brace center x Body
| 7.4
| 75
| 65 in.*lbf
|
Rear No. 1 floor panel brace
| 19
| 194
| 14
|
Front axle assembly x Suspension arm
| 120
| 1224
| 89
|
Front axle hub nut x Front dive shaft assembly
| 294
| 2988
| 217
|
Tie rod assembly x Suspension arm
| 63
| 663
| 48
|
Drive plate x Engine assembly
| 41
| 418
| 30
|
Rear spacer x Engine assembly
| 83
| 850
| 61
|
Engine mount bracket x Body
| 35
| 357
| 26
|
Generator assembly x Engine assembly
| 43
| 438
| 32
|
Generator assembly x Wire harness
| 9.8
| 100
| 87
|
Generator bracket
| 20
| 204
| 15
|
Starter assembly x Automatic transmission unit
| 58
| 591
| 43
|
Crossmember sub-assembly x Body
| for Bolt
| 204
| 2080
| 150
|
for Nut
| 167
| 1703
| 123
|
Front stabilizer bar x Body
| 49
| 500
| 36
|
Suspension member brace x Body
| 50
| 510
| 37
|
Intake air surge tank x Engine assembly
| for Bolt
| 18
| 184
| 13
|
for Nut
| 16
| 163
| 12
|
Water by-pass hose No. 4 x Intake air surge tank
| 10
| 102
| 7
|
Surge tank stay No. 2
| 21
| 214
| 15
|
Intake manifold x Engine assembly
| 21
| 214
| 15
|
Exhaust manifold sub-assembly x Engine assembly
| 21
| 214
| 15
|
Ignition coil x engine assembly
| 10
| 102
| 7
|
Engine mount bracket x Engine assembly
| 43
| 439
| 32
|
Engine mount bracket x Engine assembly
| 43
| 439
| 32
|
Injector driver x Engine assembly
| 10
| 102
| 7
|
Water pump pulley x Engine assembly
| 21
| 214
| 15
|
Fuel pump assembly x Engine assembly
| 25
| 255
| 26
|
Fuel pipe No.2 x Fuel delivery pipe
| 10
| 102
| 7
|
Fuel pipe No. 3 x Fuel delivery pipe
| 10
| 102
| 7
|
Fuel delivery pipe x Engine assembly
| 21
| 214
| 15
|
Oil level gauge guide x Engine assembly
| 10
| 102
| 7
|
Oil level gauge guide No. 2 x Engine assembly
| 21
| 214
| 15
|
Front drive shaft assembly x Engine assembly (4WD)
| 32
| 327
| 27
|
Front differential assembly x Engine assembly (4WD)
| 87
| 890
| 64
|
ENGINE UNIT
Part Tightened
| N*m
| kgf*cm
| ft.*lbf
|
Camshaft bearing cap x Camshaft housing
| 1st
| 10
| 102
| 7
|
2nd
| 16
| 163
| 12
|
Camshaft housing x Cylinder head sub-assembly
| 28
| 286
| 21
|
No. 1 chain tensioner x Cylinder head sub-assembly
| 10
| 102
| 7
|
No. 2 chain tensioner x Cylinder head sub-assembly
| 21
| 214
| 15
|
No. 3 chain tensioner x Cylinder head sub-assembly
| 21
| 214
| 15
|
Camshaft timing gear assembly x Camshaft
| 100
| 1,020
| 74
|
No. 1 engine hanger x Cylinder head sub-assembly RH
| 33
| 33
| 24
|
No. 2 engine hanger x Cylinder head sub-assembly LH
| 33
| 33
| 24
|
Engine rear oil seal retainer x Cylinder block sub-assembly
| 10
| 102
| 7
|
Knock sensor x Cylinder block sub-assembly
| 20
| 204
| 15
|
Water outlet pipe sub-assembly x Cylinder block sub-assembly
| 10
| 102
| 7
|
Cylinder head x Cylinder block sub-assembly
| 1st
| 36
| 367
| 27
|
2nd
| Turn 90°
| Turn 90°
| Turn 90°
|
3rd
| Turn 90°
| Turn 90°
| Turn 90°
|
Cylinder head sub-assembly x Cylinder block sub-assembly
| Recessed head 1st
| 36
| 367
| 27
|
2nd
| Turn 90°
| Turn 90°
| Turn 90°
|
3rd
| Turn 90°
| Turn 90°
| Turn 90°
|
14 mm (0.55 in.) head
| 30
| 306
| 22
|
No. 1hain vibration damper x Cylinder block sub-assembly
| 20
| 204
| 15
|
No. 1 idle gear x Cylinder block sub-assembly
| 60
| 612
| 44
|
Timing chain cover plate x Timing chain or belt cover sub-assembly
| 9.1
| 93
| 81 in.*lbf
|
Timing chain or belt cover sub-assembly
| Bolt A
| 43
| 438
| 32
|
except Bolt A
| 21
| 214
| 15
|
Nut
| 21
| 214
| 15
|
Water pump assembly x Timing chain or belt cover sub-assembly
| Bolt A
| 21
| 214
| 15
|
except Bolt A
| 9.1
| 93
| 81 in.*lbf
|
Oil pan baffle plate x Cylinder block sub-assembly
| 10
| 102
| 102
|
Oil strainer stud bolt x Cylinder block and timing chin cover
| 45
| 45
| 35 in.*lbf
|
Oil pan stud bolt x Oil pan sub-assembly
| 45
| 45
| 35 in.*lbf
|
Oil strainer sub-assembly x Cylinder block and timing chain or belt cover
| 10
| 102
| 102
|
Oil pan sub-assembly x Cylinder block and timing chain cover :bolt A
| Bolt A
| 10
| 102
| 7
|
except Bolt A
| 21
| 214
| 15
|
Oil pan sub-assembly x Cylinder block and timing chain cover :nut
| 21
| 214
| 15
|
No. 2 oil pan sub-assembly x Oil pan sub-assembly
| 10
| 102
| 7
|
Oil pan drain plug x No. 2 oil pan sub-assembly
| 40
| 408
| 30
|
Crankshaft pulley x Crankshaft
| 250
| 2,550
| 184
|
Cylinder head cove sub-assembly x Cylinder head sub-assembly RH
| Bolt A
| 21
| 214
| 15
|
except Bolt A
| 10
| 102
| 7
|
Cylinder head cover sub-assembly LH x Cylinder head sub-assembly LH
| Bolt A
| 21
| 214
| 15
|
except Bolt A
| 10
| 102
| 7
|
Water by-pass joint RR x Cylinder head sub-assembly
| 10
| 102
| 7
|
With thermostat water inlet sub-assembly set nut
| 10
| 102
| 7
|
Water inlet set bolt and nut
| 10
| 102
| 7
|
Oil filter cap x Oil pan
| 25
| 255
| 18
|
Camshaft position sensor
| 10
| 102
| 7
|
Ventilation valve x Cylinder head cover sub-assembly LH
| 27
| 275
| 20
|
Oil check valve bolt x Cylinder block sub-assembly
| 60
| 612
| 44
|
Oil filter bracket x Cylinder block sub-assembly
| 21
| 214
| 15
|
Oil filter drain plug x Oil filter bracket
| 13
| 133
| 10
|
Oil pipe union x Cylinder head cover sub-assembly
| 60
| 612
| 44
|
Crankshaft position sensor x Cylinder block sub-assembly
| 10
| 102
| 7
|
Camshaft timing oil control valve assembly x Cylinder head cover
| 10
| 102
| 7
|
Cylinder block water drain cock sub-assembly
| 30
| 306
| 22
|
Water drain cock plug x Water drain cock sub-assembly
| 13
| 130
| 9
|
Spark plug x Cylinder head sub-assembly
| 18
| 184
| 13
|
Stud bolt x Cylinder sub-assembly
| for A and B bolts
| 10
| 102
| 7
|
for C bolts
| 4.0
| 41
| 35 in.*lbf
|
Union x Cylinder head sub-assembly
| 15
| 153
| 11
|
With head screw plug x Cylinder head sub-assembly
| 44
| 449
| 32
|
Main bearing cap x Cylinder block sub-assembly
| 80
| 816
| 59
|
Main bearing cap x Cylinder block sub-assembly
| 16 point head 1st
| 61
| 622
| 45
|
2nd
| Turn 90°
| Turn 90°
| Turn 90°
|
12 mm head
| 26
| 265
| 19
|
Connecting rod cap x Connecting rod
| 1st
| 25
| 250
| 28
|
2nd
| Turn 90°
| Turn 90°
| Turn 90°
|
Stud bolt x Cylinder block sub-assembly
| 10
| 102
| 7
|
No. 1 sub-assembly oil nozzle x Cylinder block sub-assembly
| 9.0
| 92
| 80 in.*lbf
|
