BRAKE ACTUATOR (w/ VSC) > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
(Click here


2. REMOVE COOL AIR INTAKE DUCT SEAL


A105932E01

  1. Remove the 7 clips and duct seal.



3. REMOVE ENGINE ROOM SIDE COVER RH


    A110866E01

  1. Remove the nut, 2 clips and side cover.



4. REMOVE ENGINE ROOM SIDE COVER LH


    A110867E01

  1. Remove the 3 clips and side cover.



5. REMOVE FRONT PILLAR TO FRONT SIDE SEAL SUB-ASSEMBLY LH


B108983E01

  1. Using a clip remover, detach the 3 clips and remove the side seal.



6. REMOVE FRONT PILLAR TO FRONT SIDE SEAL SUB-ASSEMBLY RH

  1. Remove the nut, wiper arm and blade.



7. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

  1. Remove the nut, wiper arm and blade.



8. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

  1. Remove the nut, wiper arm and blade.



9. REMOVE FRONT FENDER TO COWL SIDE SEAL LH


B107358E01

  1. Pull the cowl side seal in the direction indicated by the arrow in the illustration to detach the 2 claws and remove the cowl side seal.



10. REMOVE FRONT FENDER TO COWL SIDE SEAL RH

HINT:
Use the same procedures described for the LH side.



11. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    B111074E01

  1. Remove the 2 clips and detach the 5 claws.



    B111075E01

  1. Pull the ventilator louver in the direction indicated by the arrow in the illustration to detach the 10 claws and remove the ventilator louver.



12. SEPARATE ENGINE ROOM RELAY NO.3 BLOCK


    C113039E01

  1. Remove the bolt, nut and relay No.3 block.

    NOTICE:
    Cover the relay No.3 block with a shop rag or piece of cloth to prevent brake fluid from adhering to it.



13. REMOVE FRONT WHEEL


14. DRAIN BRAKE FLUID

NOTICE:
If brake fluid leaks onto any painted surface, clean it off completely.



15. REMOVE BRAKE MASTER WITH PLATE CYLINDER SUB-ASSEMBLY

  1. Disengage the clamp and disconnect the warning switch connector.



    C113041E01

  1. Using SST, disconnect the 2 brake tubes from the brake master cylinder sub-assembly.

    SST
    09023-00101  



    C113040E02

  1. Remove the 2 nuts and brake master cylinder sub-assembly from the brake booster assembly.

  1. Remove the O-ring from the brake master cylinder sub-assembly.



16. REMOVE ABS AND TRACTION ACTUATOR ASSEMBLY WITH BRACKET


    C113029E01

  1. Release the lock lever and disconnect the actuator connector.

  1. Using SST, disconnect the 6 brake tubes from the actuator assembly with bracket.

    SST
    09023-00101  



  1. Use tags or make a memo to identify the places to reconnect.


    C113030E01



    C105638E01

  1. Using SST, disconnect the brake No.2 tube from the flexible hose. (for LHD)

    SST
    09023-00101  



    G033299E01

  1. Using SST, disconnect the brake No.2 tube from the flexible hose. (for RHD)

    SST
    09023-00101  

  1. Separate the grommet and remove the brake No.3 tube. (for LHD)

    NOTICE:
    Do not damage the brake No.3 tube.

  1. Separate the grommet and remove the brake No.2 tube. (for RHD)

    NOTICE:
    Do not damage the brake No.2 tube.



  1. Remove the 2 bolts, nut and actuator assembly from the body with bracket.

    NOTICE:
    Do not damage the brake tubes.



    C113031E01