A960E AUTOMATIC TRANSMISSION > SERVICE DATA |
| Line pressure (Fluid temperature): 50 to 80°C (122 to 176°F) Engine idling | D position | 355 to 425 kPa (3.6 to 4.3 kgf*cm2, 51 to 62 psi) |
| R position | 608 to 708 kPa (6.2 to 7.2 kgf*cm2, 88 to 103 psi) | |
| Line pressure (Fluid temperature): 50 to 80°C (122 to 176°F) AT stall (Throttle valve fully opened) | D position | 1,213 to 1,323 kPa (12.4 to 13.5 kgf*cm2, 176 to 192 psi) |
| R position | 1,340 to 1,548 kPa (13.7 to 15.8 kgf*cm2, 194 to 225 psi) | |
| Engine stall revolution | D and R positions | 2,535 +- 150 rpm |
| Time lag | N → D position N → R position | Less than 1.2 seconds Less than 1.5 seconds |
| Engine idle speed (A/C OFF) | N position | 750 +- 50 rpm |
| Drive plate runout Torque converter runout | Max. Max. | 0.20 mm (0.0079 in.) 0.30 mm (0.0118 in.) |
| Differential gear ratio | 3.727 | |
| Shift schedule | ||
| D, 6 position | ||
| (Throttle valve fully opened) | 1 → 2 | 44 to 52 km/h (27 to 32 mph) |
| 2 → 3 | 88 to 98 km/h (55 to 61 mph) | |
| 3 → 4 | 134 to 147 km/h (83 to 91 mph) | |
| 4 → 5 | 191 to 206 km/h (119 to 128 mph) | |
| 5 → 6 | 271 to 288 km/h (168 to 179 mph) | |
| 6 → 5 | 266 to 279 km/h (165 to 173 mph) | |
| 5 → 4 | 182 to 194 km/h (113 to 121 mph) | |
| 4 → 3 | 125 to 135 km/h (78 to 84 mph) | |
| 3 → 2 | 79 to 85 km/h (49 to 53 mph) | |
| 2 → 1 | 30 to 35 km/h (19 to 22 mph) | |
| (Throttle valve fully closed) | 5 → 6 | 64 to 69 km/h (40 to 43 mph) |
| 6 → 5 | 53 to 58 km/h (33 to 36 mph) | |
| 5 position | ||
| (Throttle valve fully opened) | 1 → 2 | 44 to 52 km/h (27 to 32 mph) |
| 2 → 3 | 88 to 98 km/h (55 to 61 mph) | |
| 3 → 4 | 134 to 147 km/h (83 to 91 mph) | |
| 4 → 5 | 191 to 206 km/h (119 to 128 mph) | |
| 6 → 5 | 276 to 289 km/h (172 to 180 mph) | |
| 5 → 4 | 182 to 194 km/h (113 to 121 mph) | |
| 4 → 3 | 125 to 135 km/h (78 to 84 mph) | |
| 3 → 2 | 79 to 85 km/h (49 to 53 mph) | |
| 2 → 1 | 30 to 35 km/h (19 to 22 mph) | |
| 4 position | ||
| (Throttle valve fully opened) | 1 → 2 | 44 to 52 km/h (27 to 32 mph) |
| 2 → 3 | 88 to 98 km/h (55 to 61 mph) | |
| 3 → 4 | 134 to 147 km/h (83 to 91 mph) | |
| 5 → 4 | 198 to 210 km/h (123 to 130 mph) | |
| 4 → 3 | 125 to 135 km/h (78 to 84 mph) | |
| 3 → 2 | 79 to 85 km/h (49 to 53 mph) | |
| 2 → 1 | 30 to 35 km/h (19 to 22 mph) | |
| 3 position | ||
| (Throttle valve fully opened) | 1 → 2 | 44 to 52 km/h (27 to 32 mph) |
| 2 → 3 | 88 to 98 km/h (55 to 61 mph) | |
| 4 → 3 | 139 to 150 km/h (86 to 93 mph) | |
| 3 → 2 | 79 to 85 km/h (49 to 53 mph) | |
| 2 → 1 | 30 to 35 km/h (19 to 22 mph) | |
| 2 position | ||
| (Throttle valve fully opened) | 1 → 2 | 44 to 52 km/h (27 to 32 mph) |
| 3 → 2 | 95 to 104 km/h (59 to 65 mph) | |
| 2 → 1 | 30 to 35 km/h (19 to 22 mph) | |
| 1 position | ||
| (Throttle valve fully opened) | 2 → 1 | 42 to 48 km/h (26 to 30 mph) |
| Lock-up point | Throttle valve opening 5% | |
| D, 6, 5 position | ||
| 6th gear | Lock-up ON | 63 to 69 km/h (39 to 43 mph) |
| Lock-up OFF | 61 to 66 km/h (38 to 41 mph) | |
| 5th gear | Lock-up ON | 51 to 57 km/h (32 to 35 mph) |
| Lock-up OFF | 50 to 55 km/h (31 to 34 mph) | |
| 4 position | ||
| 4th gear | Lock-up ON | 54 to 60 km/h (34 to 37 mph) |
| Lock-up OFF | 50 to 56 km/h (31 to 35 mph) | |
| Flex lock-up point | Throttle valve opening 3% | |
| D, 6, 5, 4 (Acceleration) | ||
| 6th gear | Flex lock-up ON | 55 to 61 km/h (34 to 38 mph) |
| Flex lock-up OFF | 53 to 59 km/h (33 to 37 mph) | |
| 5th gear | Flex lock-up ON | 36 to 41 km/h (22 to 25 mph) |
| Flex lock-up OFF | 34 to 39 km/h (21 to 24 mph) | |
| 4th gear | Flex lock-up ON | 31 to 36 km/h (19 to 22 mph) |
| Flex lock-up OFF | 30 to 35 km/h (19 to 22 mph) | |
| 3th gear | Flex lock-up ON | 31 to 36 km/h (19 to 22 mph) |
| Flex lock-up OFF | 20 to 25 km/h (12 to 16 mph) | |
| 1st and reverse return spring free length | Standard: 23.74 mm (0.935 in.) |
| Rear planetary gear pinion thrust clearance | Standard: 0.2 to 0.6 mm (0.008 to 0.024 in.) |
| Rear planetary gear bushing inside diameter | Standard: 18.025 mm (0.710 in.) |
| 1st and reverse brake pack clearance | 0.5 to 0.8 mm (0.0197 to 0.0315 in.) |
| Flange thickness (1st and reverse brake) | Mark 0: 0 mm (0 in.) Mark 2: 0.2 mm (0.00787 in.) Mark 4: 0.4 mm (0.01575 in.) Mark 6: 0.6 mm (0.02362 in.) Mark 8: 0.8 mm (0.03150 in.) Mark 10: 1.0 mm (0.03937 in.) Mark 12: 1.2 mm (0.04724 in.) Mark 14: 1.4 mm (0.05512 in.) |
| Intermediate shaft run out | Standard: 0.03 mm (0.0012 in.) |
| Intermediate shaft diameter | Standard A: 22.962 to 22.975 mm (0.904 to 0.905 in.) Standard B: 22.962 to 22.975 mm (0.904 to 0.905 in.) Standard C: 27.759 to 27.775 mm (1.0929 to 1.0935 in.) Standard D: 27.759 to 27.775 mm (1.0929 to 1.0935 in.) |
| Center planetary gear pinion thrust clearance | Standard: 0.12 to 0.68 mm (0.005 to 0.027 in.) |
| Brake piston return spring No.2 free length | Standard: 22.66 mm (0.8921 in.) |
| Brake piston No.2 piston stroke | 0.6 to 0.9 mm (0.024 to 0.035 in.) |
| Flange thickness (brake piston No.2) | Mark 0: 2.0 mm (0.079 in.) Mark 1: 2.1 mm (0.083 in.) Mark 2: 2.2 mm (0.087 in.) Mark 3: 2.3 mm (0.091 in.) Mark 4: 2.4 mm (0.094 in.) Mark 5: 2.5 mm (0.098 in.) Mark 6: 2.6 mm (0.102 in.) Mark 7: 2.7 mm (0.106 in.) |
| Brake piston return spring free length | Standard: 17.05 mm (0.671 in.) |
| Front planetary gear pinion thrust clearance | Standard: 0.20 to 0.60 mm (0.008 to 0.024 in.) |
| Front planetary gear bushing inside diameter | Standard: 48.78 mm (1.9205 in.) |
| Brake piston No.1 piston stroke | 0.42 to 0.72 mm (0.017 to 0.028 in.) |
| Flange thickness (brake piston No.1) | Mark 0: 2.0 mm (0.079 in.) Mark 1: 2.2 mm (0.087 in.) Mark 2: 2.4 mm (0.094 in.) Mark 3: 2.6 mm (0.102 in.) |
| Oil pump body bushing inside diameter | Standard: 38.138 mm (1.5015 in.) |
| Startor shaft bushing inside diameter | Standard: 21.527 mm (0.8475 in.) |
| Body clearance | Standard: 0.10 to 0.17 mm (0.0039 to 0.0067 in.) |
| Tip clearance | Standard: 0.07 to 0.15 mm (0.0028 to 0.0059 in.) |
| Side clearance | Standard: 0.02 to 0.04 mm (0.00079 to 0.00157 in.) |
| Drive and driven gear thickness | Mark 0: 9.946 to 9.952 mm (0.39157 to 0.39181 in.) Mark 1: 9.953 to 9.959 mm (0.39185 to 0.39209 in.) Mark 2: 9.960 to 9.966 mm (0.39213 to 0.39236 in.) Mark 3: 9.967 to 9.973 mm (0.39240 to 0.39264 in.) Mark 4: 9.974 to 9.980 mm (0.39268 to 0.39291 in.) Mark 5: 9.981 to 9.987 mm (0.39295 to 0.39319 in.) Mark 6: 9.988 to 9.994 mm (0.39323 to 0.39346 in.) |
| Direct clutch return spring free length | Standard: 20.02 mm (0.788 in.) |
| Reverse clutch return spring free length | Standard: 21.03 mm (0.828 in.) |
| Direct clutch pack clearance | 0.5 to 0.8 mm (0.020 to 0.031 in.) |
| Flange thickness (Direct clutch) | Mark 0: 3.0 mm (0.118 in.) Mark 1: 3.1 mm (0.122 in.) Mark 2: 3.2 mm (0.126 in.) Mark 3: 3.3 mm (0.130 in.) Mark 4: 3.4 mm (0.134 in.) Mark 5: 3.5 mm (0.138 in.) Mark 6: 3.6 mm (0.142 in.) Mark 7: 3.7 mm (0.146 in.) Mark 8: 3.8 mm (0.150 in.) |
| Reverse clutch pack clearance | 0.5 to 0.8 mm (0.020 to 0.031 in.) |
| Flange thickness (Reverse clutch) | Mark 0: 2.4 mm (0.094 in.) Mark 1: 2.5 mm (0.098 in.) Mark 2: 2.6 mm (0.102 in.) Mark 3: 2.7 mm (0.106 in.) Mark 4: 2.8 mm (0.110 in.) Mark 5: 2.9 mm (0.114 in.) Mark 6: 3.0 mm (0.118 in.) Mark 7: 3.1 mm (0.122 in.) Mark 8: 3.2 mm (0.126 in.) Mark 9: 3.3 mm (0.130 in.) Mark A: 3.4 mm (0.134 in.) Mark B: 3.5 mm (0.138 in.) |
| Forward clutch return spring free length | Standard: 26.29 mm (1.035 in.) |
| Forward clutch pack clearance | 0.56 to 0.86 mm (0.0220 to 0.339 in.) |
| Flange thickness (Forward clutch) | Mark 0: 3.0 mm (0.118 in.) Mark 1: 3.1 mm (0.122 in.) Mark 2: 3.2 mm (0.126 in.) Mark 3: 3.3 mm (0.130 in.) Mark 4: 3.4 mm (0.134 in.) Mark 5: 3.5 mm (0.138 in.) Mark 6: 3.6 mm (0.142 in.) Mark 7: 3.7 mm (0.146 in.) Mark 8: 3.8 mm (0.150 in.) Mark 9: 3.9 mm (0.154 in.) |
| Coast clutch pack clearance | 0.4 to 0.7 mm (0.0157 to 0.0276 in.) |
| Flange thickness (Coast clutch) | Mark 0: 3.0 mm (0.118 in.) Mark 1: 3.1 mm (0.122 in.) Mark 2: 3.2 mm (0.126 in.) Mark 3: 3.3 mm (0.130 in.) Mark 4: 3.4 mm (0.134 in.) Mark 5: 3.5 mm (0.138 in.) Mark 6: 3.6 mm (0.142 in.) Mark 7: 3.7 mm (0.146 in.) Mark 8: 3.8 mm (0.150 in.) Mark 9: 3.9 mm (0.154 in.) |
| Forward clutch hub inside diameter | Standard: 23.037 to 23.062 mm (0.907 to 0.908 in.) |
| Reverse clutch hub inside diameter | Standard: 33.312 to 33.337 mm (1.3115 to 1.3125 in.) |
| Spring | Free Length/Outer diameter mm (in.) | Color |
| B1(Inner) | 44.98 (1.7709)/11.30 (0.445) | Natural |
| B1(Outer) | 46.36 (1.8252)/17.10 (0.6732) | Natural |
| C2
| 65.07 (2.5618)/16.2(0.6378) | Pink |
| B3
| 64.5 (2.539)/19.5 (0.768) | Orange |
| C3(Inner) | 44.0 (1.732)/14.0 (0.551) | Yellow |
| C3(Outer) | 76.65 (3.0178)/20.10 (0.7913) | White |
| Clearance | 0.02 to 0.12 mm (0.0008 to 0.0047 in.) |
| Flange thickness | No.1: 3.80 mm (0.1496 in.) No.2: 3.85 mm (0.1516 in.) No.3: 3.90 mm (0.1535 in.) No.4: 3.95 mm (0.1555 in.) No.5: 4.00 mm (0.1575 in.) No.6: 4.05 mm (0.1594 in.) No.7: 4.10 mm (0.1614 in.) No.8: 4.15 mm (0.1634 in.) No.9: 4.20 mm (0.1653 in.) No.10: 4.25 mm (0.1673 in.) No.11: 4.30 mm (0.1693 in.) No.12: 4.35 mm (0.1713 in.) |
