A761E AUTOMATIC TRANSMISSION > SERVICE DATA |
| Line pressure (Fluid temperature): 50 to 80°C (122 to 176°F) Engine Idling | D position | 355 to 425 kPa (3.6 to 4.2 kgf*cm2, 51 to 62 psi) |
| R position | 631 to 731 kPa (6.4 to 7.5 kgf*cm2, 92 to 106 psi) | |
| Line pressure (Fluid temperature): 50 to 80°C (122 to 176°F) AT stall (Throttle valve fully opened) | D position | 1,277 to 1,387 kPa (13 to 14.1 kgf*cm2, 185 to 201 psi) |
| R position | 1,462 to 1.670 kPa (15 to 17 kgf*cm2, 212 to 242 psi) | |
| Engine stall revolution | D and R positions | 2,400 +- 150 rpm |
| Time lag | N → D position N → R position | Less than 1.2 seconds Less than 1.5 seconds |
| Engine idle speed (A/C OFF) | N position | 750 +- 50 rpm |
| Drive plate runout Torque converter runout | Max. Max. | 0.20 mm (0.0079 in.) 0.30 mm (0.0118 in.) |
| Extension housing oil drive in depth from flat end | 2.0 mm (0.079 in.) | |
| Differential gear ratio | 3.615 | |
| Shift schedule | ||
| D, 6 position | ||
| (Throttle valve fully opened) | 1 → 2 | 57 to 66 km/h (35 to 41 mph) |
| 2 → 3 | 94 to 104 km/h (58 to 65 mph) | |
| 3 → 4 | 142 to 156 km/h (88 to 97 mph) | |
| 4 → 5 | 189 to 203 km/h (117 to 126 mph) | |
| 5 → 6 | 252 to 267 km/h (157 to 166 mph) | |
| 6 → 5 | 245 to 257 km/h (152 to 160 mph) | |
| 5 → 4 | 182 to 193 km/h (113 to 120 mph) | |
| 4 → 3 | 134 to 144 km/h (83 to 89 mph) | |
| 3 → 2 | 85 to 91 km/h (53 to 57 mph) | |
| 2 → 1 | 40 to 45 km/h (25 to 28 mph) | |
| (Throttle valve fully closed) | 5 → 6 | 65 to 71 km/h (40 to 44 mph) |
| 6 → 5 | 52 to 57 km/h (32 to 35 mph) | |
| 5 position | ||
| (Throttle valve fully opened) | 1 → 2 | 57 to 66 km/h (35 to 41 mph) |
| 2 → 3 | 94 to 104 km/h (58 to 65 mph) | |
| 3 → 4 | 142 to 156 km/h (88 to 97 mph) | |
| 4 → 5 | 189 to 203 km/h (117 to 126 mph) | |
| 6 → 5 | 252 to 264 km/h (157 to 164 mph) | |
| 5 → 4 | 182 to 193 km/h (113 to 120 mph) | |
| 4 → 3 | 134 to 144 km/h (83 to 89 mph) | |
| 3 → 2 | 85 to 91 km/h (53 to 57 mph) | |
| 2 → 1 | 40 to 45 km/h (25 to 28 mph) | |
| 4 position | ||
| (Throttle valve fully opened) | 1 → 2 | 57 to 66 km/h (35 to 41 mph) |
| 2 → 3 | 94 to 104 km/h (58 to 65 mph) | |
| 3 → 4 | 142 to 156 km/h (88 to 97 mph) | |
| 5 → 4 | 203 to 214 km/h (126 to 133 mph) | |
| 4 → 3 | 134 to 144 km/h (83 to 89 mph) | |
| 3 → 2 | 85 to 91 km/h (53 to 57 mph) | |
| 2 → 1 | 40 to 45 km/h (25 to 28 mph) | |
| 3 position | ||
| (Throttle valve fully opened) | 1 → 2 | 57 to 66 km/h (35 to 41 mph) |
| 2 → 3 | 94 to 104 km/h (58 to 65 mph) | |
| 4 → 3 | 148 to 158 km/h (92 to 98 mph) | |
| 3 → 2 | 85 to 91 km/h (53 to 57 mph) | |
| 2 → 1 | 40 to 45 km/h (25 to 28 mph) | |
| 2 position | ||
| (Throttle valve fully opened) | 1 → 2 | 57 to 66 km/h (35 to 41 mph) |
| 3 → 2 | 99 to 109 km/h (62 to 68 mph) | |
| 2 → 1 | 40 to 45 km/h (25 to 28 mph) | |
| 1 position | ||
| (Throttle valve fully opened) | 2 → 1 | 40 to 45 km/h (25 to 28 mph) |
| Lock-up point | Throttle valve opening 5% | |
| D, 6, 5 position | ||
| 6th gear | Lock-up ON | 69 to 75 km/h (43 to 47 mph) |
| Lock-up OFF | 66 to 71 km/h (41 to 44 mph) | |
| 5th gear | Lock-up ON | 56 to 61 km/h (35 to 38 mph) |
| Lock-up OFF | 52 to 57 km/h (32 to 35 mph) | |
| 4 position | ||
| 4th gear | Lock-up ON | 56 to 61 km/h (35 to 38 mph) |
| Lock-up OFF | 52 to 57 km/h (32 to 35 mph) | |
| Flex lock-up point | Throttle valve opening 3% | |
| D, 6, 5, 4 (Acceleration) | ||
| 6th gear | Flex lock-up ON | 56 to 61 km/h (35 to 38 mph) |
| Flex lock-up OFF | 54 to 60 km/h (34 to 37 mph) | |
| 5th gear | Flex lock-up ON | 45 to 50 km/h (28 to 31 mph) |
| Flex lock-up OFF | 43 to 48 km/h (27 to 30 mph) | |
| 4th gear | Flex lock-up ON | 32 to 37 km/h (20 to 23 mph) |
| Flex lock-up OFF | 31 to 36 km/h (19 to 22 mph) | |
| 3th gear | Flex lock-up ON | 32 to 37 km/h (20 to 23 mph) |
| Flex lock-up OFF | 22 to 26 km/h (14 to 16 mph) | |
| 1st and reverse return spring free length | Standard: 23.74 mm (0.935 in.) |
| Rear planetary gear pinion thrust clearance | Standard: 0.2 to 0.6 mm (0.008 to 0.024 in.) |
| Rear planetary gear bushing inside diameter | Standard: 20.025 mm (0.7884 in.) |
| 1st and reverse brake pack clearance | 0.4 to 0.7 mm (0.016 to 0.028 in.) |
| Flange thickness (1st and reverse brake) | Mark 0: 0 mm (0 in.) Mark 2: 0.2 mm (0.00787 in.) Mark 4: 0.4 mm (0.01575 in.) Mark 6: 0.6 mm (0.02362 in.) Mark 8: 0.8 mm (0.03150 in.) Mark 10: 1.0 mm (0.03937 in.) Mark 12: 1.2 mm (0.04724 in.) Mark 14: 1.4 mm (0.05512 in.) |
| Intermediate shaft run out | Standard: 0.03 mm (0.0012 in.) |
| Intermediate shaft diameter | Standard A: 25.962 to 25.975 mm (1.022 to 1.023 in.) Standard B: 25.962 to 25.975 mm (1.022 to 1.023 in.) Standard C: 32.062 to 32.075 mm (1.262 to 1.263 in.) Standard D: 32.062 to 32.075 mm (1.262 to 1.263 in.) |
| Rear planetary ring gear flange bushing inside diameter | Standard: 32.19 mm (1.2673 in.) |
| Center planetary gear pinion thrust clearance | Standard: 0.12 to 0.68 mm (0.005 to 0.027 in.) |
| Brake piston return spring No.2 free length | Standard: 22.66 mm (0.8921 in.) |
| Brake piston No.2 piston stroke | 0.6 to 0.9 mm (0.024 to 0.035 in.) |
| Flange thickness (brake piston No.2) | Mark 0: 2.0 mm (0.079 in.) Mark 1: 2.1 mm (0.083 in.) Mark 2: 2.2 mm (0.087 in.) Mark 3: 2.3 mm (0.091 in.) Mark 4: 2.4 mm (0.094 in.) Mark 5: 2.5 mm (0.098 in.) Mark 6: 2.6 mm (0.102 in.) Mark 7: 2.7 mm (0.106 in.) |
| Brake piston return spring free length | Standard: 17.05 mm (0.671 in.) |
| Front planetary gear pinion thrust clearance | Standard: 0.20 to 0.60 mm (0.008 to 0.024 in.) |
| Front planetary gear bushing inside diameter | Standard: 57.43 mm (2.261 in.) |
| Brake piston No.1 piston stroke | 0.42 to 0.72 mm (0.017 to 0.028 in.) |
| Flange thickness (brake piston No.1) | Mark 0: 2.0 mm (0.079 in.) Mark 1: 2.2 mm (0.087 in.) Mark 2: 2.4 mm (0.094 in.) Mark 3: 2.6 mm (0.102 in.) |
| Brake piston return spring No.3 free length | Standard: 15.72 mm (0.619 in.) |
| Oil pump body bushing inside diameter | Standard: 38.138 mm (1.5015 in.) |
| Stator shaft bushing inside diameter | Standard (Front side): 21.527 mm (0.8475 in.) Standard (Rear side): 32.08 mm (1.261 in.) |
| Body clearance | Standard: 0.10 to 0.17 mm (0.0039 to 0.0067 in.) |
| Tip clearance | Standard: 0.07 to 0.15 mm (0.0028 to 0.0059 in.) |
| Side clearance | Standard: 0.03 to 0.05 mm (0.0012 to 0.0020 in.) |
| Drive and driven gear thickness | Mark 0: 10.736 to 10.742 mm (0.42268 to 0.42291 in.) Mark 1: 10.743 to 10.749 mm (0.42296 to 0.42319 in.) Mark 2: 10.750 to 10.756 mm (0.42323 to 0.42346 in.) Mark 3: 10.757 to 10.763 mm (0.42350 to 0.42374 in.) Mark 4: 10.764 to 10.770 mm (0.42378 to 0.42401 in.) Mark 5: 10.771 to 10.777 mm (0.42405 to 0.42429 in.) Mark 6: 10.778 to 10.784 mm (0.42433 to 0.42457 in.) |
| Direct clutch return spring free length | Standard: 19.51 mm (0.768 in.) |
| Reverse clutch return spring free length | Standard: 21.04 mm (0.828 in.) |
| Direct clutch pack clearance | 0.5 to 0.8 mm (0.020 to 0.031 in.) |
| Flange thickness (Direct clutch) | Mark 0: 3.0 mm (0.118 in.) Mark 1: 3.1 mm (0.122 in.) Mark 2: 3.2 mm (0.126 in.) Mark 3: 3.3 mm (0.130 in.) Mark 4: 3.4 mm (0.134 in.) Mark 5: 3.5 mm (0.138 in.) Mark 6: 3.6 mm (0.142 in.) Mark 7: 3.7 mm (0.146 in.) Mark 8: 3.8 mm (0.150 in.) |
| Reverse clutch pack clearance | 0.5 to 0.8 mm (0.020 to 0.031 in.) |
| Flange thickness (Reverse clutch) | Mark 0: 2.8 mm (0.110 in.) Mark 1: 2.9 mm (0.114 in.) Mark 2: 3.0 mm (0.118 in.) Mark 3: 3.1 mm (0.122 in.) Mark 4: 3.2 mm (0.126 in.) Mark 5: 3.3 mm (0.130 in.) Mark 6: 3.4 mm (0.134 in.) Mark 7: 3.5 mm (0.138 in.) Mark 8: 3.6 mm (0.142 in.) Mark 9: 3.7 mm (0.146 in.) Mark A: 3.8 mm (0.150 in.) |
| Forward clutch return spring free length | Standard: 24.64 mm (0.9701 in.) |
| Coast clutch pack clearance | 0.3 to 0.6 mm (0.012 to 0.024 in.) |
| Flange thickness (Coast clutch) | Mark 0: 3.0 mm (0.118 in.) Mark 1: 3.1 mm (0.122 in.) Mark 2: 3.2 mm (0.126 in.) Mark 3: 3.3 mm (0.130 in.) Mark 4: 3.4 mm (0.134 in.) Mark 5: 3.5 mm (0.138 in.) Mark 6: 3.6 mm (0.142 in.) Mark 7: 3.7 mm (0.146 in.) Mark 8: 3.8 mm (0.150 in.) Mark 9: 3.9 mm (0.154 in.) |
| Forward clutch pack clearance | 0.56 to 0.86 mm (0.0220 to 0.339 in.) |
| Flange thickness (Forward clutch) | Mark 0: 3.0 mm (0.118 in.) Mark 1: 3.1 mm (0.122 in.) Mark 2: 3.2 mm (0.126 in.) Mark 3: 3.3 mm (0.130 in.) Mark 4: 3.4 mm (0.134 in.) Mark 5: 3.5 mm (0.138 in.) Mark 6: 3.6 mm (0.142 in.) Mark 7: 3.7 mm (0.146 in.) Mark 8: 3.8 mm (0.150 in.) Mark 9: 3.9 mm (0.154 in.) Mark A: 4.0 mm (0.158 in.) |
| Forward clutch hub inside diameter | Standard: 26.037 to 26.062 mm (1.0251 to 1.0261 in.) |
| Reverse clutch hub inside diameter | Standard: 35.812 to 35.837 mm (1.4099 to 1.4109 in.) |
| Spring | Free Length/Outer diameter mm (in.) | Color |
| B1(Inner) | 44.98 (1.7709)/11.30 (0.445) | Natural |
| B1(Outer) | 46.36 (1.8252)/17.10 (0.6732) | Natural |
| C2
| 63.14 (2.4858)/16.0(0.6299) | Light Gray |
| B3
| 64.5 (2.539)/19.5 (0.768) | Orange |
| C3(Inner) | 44.0 (1.732)/14.0 (0.551) | Yellow |
| C3(Outer) | 76.65 (3.0178)/20.10 (0.7913) | Natural |
| Clearance | 0.02 to 0.12 mm (0.0008 to 0.0047 in.) |
| Flange thickness | No.1: 3.80 mm (0.1496 in.) No.2: 3.85 mm (0.1516 in.) No.3: 3.90 mm (0.1535 in.) No.4: 3.95 mm (0.1555 in.) No.5: 4.00 mm (0.1575 in.) No.6: 4.05 mm (0.1594 in.) No.7: 4.10 mm (0.1614 in.) No.8: 4.15 mm (0.1634 in.) No.9: 4.20 mm (0.1653 in.) No.10: 4.25 mm (0.1673 in.) No.11: 4.30 mm (0.1693 in.) No.12: 4.35 mm (0.1713 in.) |
