DIFFERENTIAL > SERVICE DATA



REAR DIFFERENTIAL CARRIER ASSEMBLY (for 3GR-FSE) 
Rear differential carrier oil seal drive in depth
1.55 to 2.45 mm (0.061 to 0.096 in.)
Rear differential side gear shaft oil seal drive in depth
-0.5 to 0.5 mm (-0.020 to 0.020 in.)
Differential ring gear runout
Maximum: 0.07 mm (0.0028 in.)
Differential ring gear backlash
0.13 to 0.18 mm (0.0051 to 0.0071 in.)
Differential pinion to side gear backlash
0.05 to 0.20 mm (0.0020 to 0.0079 in.)
Companion flange runout
Maximum: 0.09 mm (0.0035 in.)
Drive pinion preload (at starting)
New bearing: 0.88 to 1.47 N*m (9.0 to 15.0 kgf*cm, 7.8 to 13.0 in.*lbf)
Reused bearing: 0.39 to 0.69 N*m (4.0 to 7.0 kgf*cm, 3.5 to 6.1 in.*lbf)
Total preload (Drive pinion preload plus)
0.39 to 0.59 N*m (4.0 to 6.0 kgf*cm, 3.5 to 5.2 in.*lbf)
Differential case runout
Maximum: 0.07 mm (0.0028 in.)
Side gear thrust No.1 washer thickness mm (in.)
1.48 to 1.52 (0.0583 to 0.0598)
1.53 to 1.57 (0.0602 to 0.0618)
1.58 to 1.62 (0.0622 to 0.0638)
1.63 to 1.67 (0.0642 to 0.0657)
1.68 to 1.72 (0.0661 to 0.0677)
1.73 to 1.77 (0.0681 to 0.0697)
1.78 to 1.82 (0.0701 to 0.0717)
1.83 to 1.87 (0.0720 to 0.0736)
1.88 to 1.92 (0.0740 to 0.0756)
Side gear shaft plate washer thickness mm (in.)
2.57 to 2.59 (0.1012 to 0.1020)
2.59 to 2.61 (0.1020 to 0.1028)
2.61 to 2.63 (0.1028 to 0.1035)
2.63 to 2.65 (0.1035 to 0.1043)
2.65 to 2.67 (0.1043 to 0.1051)
2.67 to 2.69 (0.1051 to 0.1059)
2.69 to 2.71 (0.1059 to 0.1067)
2.71 to 2.73 (0.1067 to 0.1075)
2.73 to 2.75 (0.1075 to 0.1083)
2.75 to 2.77 (0.1083 to 0.1091)
2.77 to 2.79 (0.1091 to 0.1098)
2.79 to 2.81 (0.1098 to 0.1106)
2.81 to 2.83 (0.1106 to 0.1114)
2.83 to 2.85 (0.1114 to 0.1122)
2.85 to 2.87 (0.1122 to 0.1130)
2.87 to 2.89 (0.1130 to 0.1138)
2.89 to 2.91 (0.1138 to 0.1146)
2.91 to 2.93 (0.1146 to 0.1154)
2.93 to 2.95 (0.1154 to 0.1161)
2.95 to 2.97 (0.1161 to 0.1169)
2.97 to 2.99 (0.1169 to 0.1177)
2.99 to 3.01 (0.1177 to 0.1185)
3.01 to 3.03 (0.1185 to 0.1193)
3.03 to 3.05 (0.1193 to 0.1201)
3.05 to 3.07 (0.1201 to 0.1209)
3.07 to 3.09 (0.1209 to 0.1217)
3.09 to 3.11 (0.1217 to 0.1224)
3.11 to 3.13 (0.1224 to 0.1232)
3.13 to 3.15 (0.1232 to 0.1240)
3.15 to 3.17 (0.1240 to 0.1248)
3.17 to 3.19 (0.1248 to 0.1256)
3.19 to 3.21 (0.1256 to 0.1264)
3.21 to 3.23 (0.1264 to 0.1271)
3.23 to 3.25 (0.1271 to 0.1280)
3.25 to 3.27 (0.1280 to 0.1287)
3.27 to 3.29 (0.1287 to 0.1295)
3.29 to 3.31 (0.1295 to 0.1303)
3.31 to 3.33 (0.1303 to 0.1311)
3.33 to 3.35 (0.1311 to 0.1319)
3.35 to 3.37 (0.1319 to 0.1327)
3.37 to 3.39 (0.1327 to 0.1335)
3.39 to 3.41 (0.1335 to 0.1343)
3.41 to 3.43 (0.1343 to 0.1350)
3.43 to 3.45 (0.1350 to 0.1358)
3.45 to 3.47 (0.1358 to 0.1366)
3.47 to 3.49 (0.1366 to 0.1374)
Rear differential drive pinion plate washer thickness mm (in.)
1.69 to 1.71 (0.0665 to 0.0673)
1.72 to 1.74 (0.0677 to 0.0685)
1.75 to 1.77 (0.0688 to 0.0697)
1.78 to 1.80 (0.0701 to 0.0709)
1.81 to 1.83 (0.0713 to 0.0720)
1.84 to 1.86 (0.0724 to 0.0732)
1.87 to 1.89 (0.0736 to 0.0744)
1.90 to 1.92 (0.0748 to 0.0756)
1.93 to 1.95 (0.0760 to 0.0768)
1.96 to 1.98 (0.0772 to 0.0780)
1.99 to 2.01 (0.0783 to 0.0791)
2.02 to 2.04 (0.0795 to 0.0803)
2.05 to 2.07 (0.0807 to 0.0815)
2.08 to 2.10 (0.0819 to 0.0827)
2.11 to 2.13 (0.0831 to 0.0839)
2.14 to 2.16 (0.0843 to 0.0850)
2.17 to 2.19 (0.0854 to 0.0862)
2.20 to 2.22 (0.0866 to 0.0874)
2.23 to 2.25 (0.0878 to 0.0886)
2.26 to2.28 (0.0890 to 0.0898)
2.29 to 2.31 (0.0902 to 0.0909)
2.32 to 2.34 (0.0913 to 0.0921)

REAR DIFFERENTIAL CARRIER ASSEMBLY (for 3GR-FE) 
Rear differential carrier oil seal drive in depth
1.55 to 2.45 mm (0.061 to 0.096 in.)
Rear differential side gear shaft oil seal drive in depth
-0.5 to 0.5 mm (-0.020 to 0.020 in.)
Differential ring gear runout
Maximum: 0.07 mm (0.0028 in.)
Differential ring gear backlash
0.13 to 0.18 mm (0.0051 to 0.0071 in.)
Differential pinion to side gear backlash
0.05 to 0.20 mm (0.0020 to 0.0079 in.)
Companion flange runout
Maximum: 0.09 mm (0.0035 in.)
Drive pinion preload (at starting)
New bearing: 0.88 to 1.47 N*m (9.0 to 15.0 kgf*cm, 7.8 to 13.0 in.*lbf)
Reused bearing: 0.39 to 0.69 N*m (4.0 to 7.0 kgf*cm, 3.5 to 6.1 in.*lbf)
Total preload (Drive pinion preload plus)
0.39 to 0.59 N*m (4.0 to 6.0 kgf*cm, 3.5 to 5.2 in.*lbf)
Differential case runout
Maximum: 0.07 mm (0.0028 in.)
Side gear thrust No.1 washer thickness mm (in.)
1.48 to 1.52 (0.0583 to 0.0598)
1.53 to 1.57 (0.0602 to 0.0618)
1.58 to 1.62 (0.0622 to 0.0638)
1.63 to 1.67 (0.0642 to 0.0657)
1.68 to 1.72 (0.0661 to 0.0677)
1.73 to 1.77 (0.0681 to 0.0697)
1.78 to 1.82 (0.0701 to 0.0717)
1.83 to 1.87 (0.0720 to 0.0736)
1.88 to 1.92 (0.0740 to 0.0756)
Side gear shaft plate washer thickness mm (in.)
2.57 to 2.59 (0.1012 to 0.1020)
2.59 to 2.61 (0.1020 to 0.1028)
2.61 to 2.63 (0.1028 to 0.1035)
2.63 to 2.65 (0.1035 to 0.1043)
2.65 to 2.67 (0.1043 to 0.1051)
2.67 to 2.69 (0.1051 to 0.1059)
2.69 to 2.71 (0.1059 to 0.1067)
2.71 to 2.73 (0.1067 to 0.1075)
2.73 to 2.75 (0.1075 to 0.1083)
2.75 to 2.77 (0.1083 to 0.1091)
2.77 to 2.79 (0.1091 to 0.1098)
2.79 to 2.81 (0.1098 to 0.1106)
2.81 to 2.83 (0.1106 to 0.1114)
2.83 to 2.85 (0.1114 to 0.1122)
2.85 to 2.87 (0.1122 to 0.1130)
2.87 to 2.89 (0.1130 to 0.1138)
2.89 to 2.91 (0.1138 to 0.1146)
2.91 to 2.93 (0.1146 to 0.1154)
2.93 to 2.95 (0.1154 to 0.1161)
2.95 to 2.97 (0.1161 to 0.1169)
2.97 to 2.99 (0.1169 to 0.1177)
2.99 to 3.01 (0.1177 to 0.1185)
3.01 to 3.03 (0.1185 to 0.1193)
3.03 to 3.05 (0.1193 to 0.1201)
3.05 to 3.07 (0.1201 to 0.1209)
3.07 to 3.09 (0.1209 to 0.1217)
3.09 to 3.11 (0.1217 to 0.1224)
3.11 to 3.13 (0.1224 to 0.1232)
3.13 to 3.15 (0.1232 to 0.1240)
3.15 to 3.17 (0.1240 to 0.1248)
3.17 to 3.19 (0.1248 to 0.1256)
3.19 to 3.21 (0.1256 to 0.1264)
3.21 to 3.23 (0.1264 to 0.1271)
3.23 to 3.25 (0.1271 to 0.1280)
3.25 to 3.27 (0.1280 to 0.1287)
3.27 to 3.29 (0.1287 to 0.1295)
3.29 to 3.31 (0.1295 to 0.1303)
3.31 to 3.33 (0.1303 to 0.1311)
3.33 to 3.35 (0.1311 to 0.1319)
3.35 to 3.37 (0.1319 to 0.1327)
3.37 to 3.39 (0.1327 to 0.1335)
3.39 to 3.41 (0.1335 to 0.1343)
3.41 to 3.43 (0.1343 to 0.1350)
3.43 to 3.45 (0.1350 to 0.1358)
3.45 to 3.47 (0.1358 to 0.1366)
3.47 to 3.49 (0.1366 to 0.1374)
Rear differential drive pinion plate washer thickness mm (in.)
1.69 to 1.71 (0.0665 to 0.0673)
1.72 to 1.74 (0.0677 to 0.0685)
1.75 to 1.77 (0.0688 to 0.0697)
1.78 to 1.80 (0.0701 to 0.0709)
1.81 to 1.83 (0.0713 to 0.0720)
1.84 to 1.86 (0.0724 to 0.0732)
1.87 to 1.89 (0.0736 to 0.0744)
1.90 to 1.92 (0.0748 to 0.0756)
1.93 to 1.95 (0.0760 to 0.0768)
1.96 to 1.98 (0.0772 to 0.0780)
1.99 to 2.01 (0.0783 to 0.0791)
2.02 to 2.04 (0.0795 to 0.0803)
2.05 to 2.07 (0.0807 to 0.0815)
2.08 to 2.10 (0.0819 to 0.0827)
2.11 to 2.13 (0.0831 to 0.0839)
2.14 to 2.16 (0.0843 to 0.0850)
2.17 to 2.19 (0.0854 to 0.0862)
2.20 to 2.22 (0.0866 to 0.0874)
2.23 to 2.25 (0.0878 to 0.0886)
2.26 to2.28 (0.0890 to 0.0898)
2.29 to 2.31 (0.0902 to 0.0909)
2.32 to 2.34 (0.0913 to 0.0921)

REAR DIFFERENTIAL CARRIER ASSEMBLY (for 3UZ-FE) 
Rear differential carrier oil seal drive in depth
-0.5 to 0.5 mm (-0.020 to 0.020 in.)
Rear differential side gear shaft oil seal drive in depth
-0.5 to 0.5 mm (-0.020 to 0.020 in.)
Differential ring gear runout
Maximum: 0.05 mm (0.0020 in.)
Differential ring gear backlash
0.08 to 0.13 mm (0.0031 to 0.0051 in.)
Differential pinion to side gear backlash
0 mm (0 in.)
Differential drive pinion runout
Maximum: 0.08 mm (0.0031 in.)
Drive pinion preload (at starting)
New bearing: 1.2 to 1.8 N*m (12.2 to 18.4 kgf*cm, 10.6 to 15.9 in.*lbf)
Reused bearing: 0.5 to 0.8 N*m (5.0 to 8.0 kgf*cm, 4.3 to 6.9 in.*lbf)
Total preload (Drive pinion preload plus)
0.48 to 1.43 N*m (4.89 to 14.58 kgf*cm, 4.25 to 12.66 in.*lbf)
Rear differential side gear shaft snap ring thickness mm (in.)
3.66 (0.1441)
3.68 (0.1449)
3.70 (0.1457)
3.72 (0.1465)
3.74 (0.1472)
3.76 (0.1480)
3.78 (0.1488)
3.80 (0.1496)
3.82 (0.1503)
3.84 (0.1512)
3.86 (0.1520)
3.88 (0.1528)
3.90 (0.1535)
3.92 (0.1543)
3.94 (0.1551)
3.96 (0.1559)
3.98 (0.1567)
4.00 (0.1575)
4.02 (0.1583)
4.04 (0.1591)
4.06 (0.1598)
4.08 (0.1606)
4.10 (0.1614)
4.12 (0.1622)
4.14 (0.1630)
4.16 (0.1638)
4.18 (0.1646)
4.20 (0.1654)
4.22 (0.1661)
4.24 (0.1669)
4.26 (0.1677)
4.28 (0.1685)
4.30 (0.1693)
4.32 (0.1701)
4.34 (0.1709)
4.36 (0.1717)
4.38 (0.1724)
4.40 (0.1732)
4.42 (0.1740)