DATA LIST / ACTIVE TEST
System information
| READ DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful as intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the DATA LIST information early in troubleshooting is one way to save diagnostic time.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Read the DATA LIST.
Power source control ECU: Item
Measurement Item / Display (Range)
Normal Condition
Diagnostic Note
Shift P Sig
Shift P switch / ON or OFF
ON: Shift P position
OFF: Shift non-P position
-
Str Unlock SW
Steering lock condition / ON or OFF
ON: Steering is unlocked
OFF: Steering is locked
-
Stop Lamp SW1
Stop light switch 1 / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
St SW1
Start switch 1 / ON or OFF
ON: Engine switch is pushed
OFF: Engine switch is not pushed
-
St SW2
Start switch 2 / ON or OFF
ON: Engine switch is pushed
OFF: Engine switch is not pushed
-
N SW / C SW
Neutral start switch (A/T) clutch start switch (M/T) / ON or OFF
ON: Shift position is P or N (A/T) clutch pedal depressed (M/T)
OFF: Shift position is neither P nor N (A/T) clutch pedal released (M/T)
-
Ratch Circuit
Ratch circuit / ON or OFF
ON: Engine switch on (IG) or engine running
OFF: Engine switch off, on (ACC)
-
IG1 Relay Mon1
IG1 outer relay monitor / ON or OFF
ON: Engine switch on (IG)
OFF: Engine switch off
-
IG1 Relay Mon2
IG1 inner relay monitor / ON or OFF
ON: Engine switch on (IG)
OFF: Engine switch off
-
IG2 Relay Mon1
IG2 outer relay monitor / ON or OFF
ON: Engine switch on (IG)
OFF: Engine switch off
-
IG2 Relay Mon2
IG2 inner relay monitor / ON or OFF
ON: Engine switch on (IG)
OFF: Engine switch off
-
St Relay Mon
STARTER relay monitor / ON or OFF
ON: Engine is cranking
OFF: Engine is not cranking
Engine is cranking with engine switch on (IG) and shift lever in P or N (A/T) or clutch pedal depressed (M/T)
St Request Sig
Starter request signal monitor / ON or OFF
ON: ST relay is ON
OFF: ST relay is OFF
Engine switch pressed and held with shift lever in P or N (A/T) or with clutch pedal depressed (M/T)
ACC Relay Mon
ACC relay monitor / ON or OFF
ON: Engine switch on (ACC)
OFF: Engine switch off
-
ACC Cut Sig
ACC relay cut signal / ON or OFF
ON: Engine is cranking
OFF: Engine is not cranking
-
E/G Cond
Engine condition / STOP or RUN
STOP: Engine is stopped
RUN: Engine is running
-
Vehicle Spd Sig
Vehicle speed signal / STOP or RUN
STOP: Vehicle is stopped
RUN: Vehicle is running
-
Shift P Signal Pulse
Shift P position signal (A/T) / NORMAL1, NORMAL2, NORMAL3, ERROR1, ERROR2, ERROR3, UNKNOWN
NORMAL1: Normal condition and shift position is condition unknown
NORMAL2: Normal condition and shift position is P
NORMAL3: Normal condition and shift position is not P
ERROR1: Malfunction condition and shift position is condition unknown
ERROR2: Malfunction condition and shift position is P
ERROR3: Malfunction condition and shift position is not P
UNKNOWN: Condition unknown
-
Pwr Cond
Power supply condition / ALL, ACC ON, IG1 IG2, ST ON
ALL: All relays are OFF
ACC ON: ACC relay is ON
IG1: IG1 relay is ON
IG2: IG2 relay is ON
ST ON: ST request signal is ON
-
#Code
Number of diagnostic codes / Min.: 0, Max.: 255
-
-
| PERFORM ACTIVE TEST |
- HINT:
- Performing the intelligent tester's ACTIVE TEST allows the relay, VSV, actuator and other items to be operated without removing any parts. Performing the ACTIVE TEST early in troubleshooting is one way to save time. The DATA LIST can be displayed during the ACTIVE TEST.
Connect the intelligent tester to the DLC3
Turn the engine switch on (IG).
Perform the ACTIVE TEST according to the display on the tester.
| Item |
Test Details |
Diagnostic Note |
| Lighting Ind |
Indicator for lighting ON / OFF |
- |
| Ind Condition |
Indicator Green / Amber / No Sig |
- |
| S Lock Pwr |
Power supply for steering lock ECU ON / OFF |
- |