Lexus IS250 · Service Manual RESTRAINTS

REMOVAL

Removal / installation


1. REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

  1. B121659E01
    Detach the 2 front hooks of the seat cushion from the vehicle body.

    NOTICE:
    Follow the instructions below carefully as the cushion frame deforms easily.


    1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

    2. Repeat for the other hook.

  1. Detach the 2 rear hooks of the seat cushion from the seatback.

  1. Remove the seat cushion.


2. REMOVE REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

  1. B119425
    Remove the bolt and the rear seat inner with center belt assembly LH.


3. REMOVE REAR SEAT HEADREST ASSEMBLY

4. REMOVE REAR SEAT CENTER HEADREST ASSEMBLY

5. REMOVE BENCH TYPE REAR SEATBACK ASSEMBLY

  1. B105996E02
    Using a screwdriver, detach the claws to open the cap of the 3 rear seat shoulder belt guides.

  1. B120546E02
    Using a screwdriver, detach the claw to open the cap of the 3 rear seat shoulder belt guides.

  1. B121660
    Remove the 4 bolts and rear seatback assembly.


6. REMOVE REAR DOOR SCUFF PLATE LH

  1. B125386E01
    Put protective tape around the rear door scuff plate.

  1. Using a moulding remover, disengage the 2 clips.

  1. B125387
    Disengage the 5 claws and remove the the rear door scuff plate LH.


7. REMOVE REAR DOOR SCUFF PLATE RH

8. REMOVE REAR SEAT SIDE GARNISH LH

  1. B125408
    Disengage the 5 claws and remove the rear seat side garnish LH.


9. REMOVE REAR SEAT SIDE GARNISH RH

10. REMOVE ROOF SIDE INNER GARNISH LH

  1. B125407
    Disengage the 4 clips and claw, and remove the roof side inner garnish LH.


11. REMOVE ROOF SIDE INNER GARNISH RH

12. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/o Rear Sunshade)

  1. B122791
    Remove the bolt and disconnect the floor end of the rear seat 3 point type belt assembly LH.

    HINT:
    Use the same procedures for the RH side and the LH side.

  1. B119437
    Remove the bolt and disconnect the floor end of the rear seat inner with center belt assembly RH.

  1. B122798
    Using a moulding remover, disengage the 4 claws and remove the rear seat shoulder belt cover LH.

    HINT:
    Use the same procedures for the RH side and LH side.

  1. B121573
    Using a moulding remover, disengage the 4 claws and remove the rear seat shoulder belt cover center.

  1. B124252
    Disengage the 3 clips and raise the front portion of the package tray trim panel assembly.

  1. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.

  1. Disconnect the connector from the center stop light assembly.

  1. Disengage the 5 claws and remove the package tray trim panel assembly and the center stop light assembly as a unit.


13. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade)

  1. B122791
    Remove the bolt and disconnect the floor end of the rear seat 3 point type belt assembly LH.

    HINT:
    Use the same procedures for the RH side and the LH side.

  1. B119437
    Remove the bolt and disconnect the floor end of the rear seat inner with center belt assembly RH.

  1. B122798
    Using a moulding remover, disengage the 4 claws and remove the rear seat shoulder belt cover LH.

    HINT:
    Use the same procedures for the RH side and LH side.

  1. B121573
    Using a moulding remover, disengage the 4 claws and remove the rear seat shoulder belt cover center.

  1. B124253
    Disengage the 3 clips.

  1. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.

  1. Remove the package tray trim panel assembly.


14. REMOVE REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH

  1. B122052
    Remove the bolt and the rear seat inner with center belt assembly RH.

← COMPONENTSINSTALLATION →