Lexus IS250 · Service Manual BODY ELECTRICAL

REMOVAL

Removal / installation


1. REMOVE COOL AIR INTAKE DUCT SEAL

  1. B125512
    Using a clip remover, remove the 11 clips and cool air intake duct seal.


2. REMOVE FRONT BUMPER ASSEMBLY

  1. B125513E01
    Using a screwdriver, turn the pin 90 degrees and remove the 2 pin hold clips.

    HINT:
    1. Tape the screwdriver tip before use.
    2. Use the same procedures for the RH side and LH side.

  1. B125605E01
    Put protective tape around the front bumper assembly.

  1. Using a clip remover, remove the 2 clips

  1. Remove the 2 radiator grille protectors.

  1. Remove the bolt and 10 screws.

  1. B125515
    Disengage the 5 claws and disconnect the front bumper assembly as shown in the illustration.

    HINT:
    Use the same procedures for the RH side and LH side.

  1. Disconnect the headlight washer hose. (w/ headlight cleaner system)

  1. Disconnect the connector and remove the front bumper assembly.


3. REMOVE NO. 1 ULTRASONIC SENSOR

  1. Disconnect the sensor connector.

  1. E075062
    Remove the sensor retainer as shown in the illustration.

  1. Remove the No. 1 ultrasonic sensor from the front bumper.


4. REMOVE LUGGAGE COMPARTMENT TRIM COVER

5. REMOVE DECK SIDE TRIM BOX LH

6. REMOVE DECK SIDE TRIM BOX RH

7. REMOVE SPARE WHEEL COVER

8. REMOVE ROPE HOOK ASSEMBLY

  1. B125612
    Remove the 3 bolts and 3 rope hook assemblies.


9. REMOVE REAR LUGGAGE COMPARTMENT TRIM COVER

  1. B125536
    Using a clip remover, remove the 3 clips.

  1. Disengage the 4 clips and remove the rear luggage compartment trim cover.


10. REMOVE ROOM LIGHT ASSEMBLY

  1. B125537
    Disengage the claw and disconnect the No. 2 room light assembly.

  1. Disconnect the connector and remove the No. 2 room light assembly.


11. REMOVE ROPE HOOK

  1. B125538
    Remove the 2 rope hooks.


12. REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER

  1. B125539
    Remove the 3 luggage compartment trim hooks as shown in the illustration.

  1. B125540
    Using a clip remover, remove the 2 clips.

  1. Disengage the 4 claws and remove the front luggage compartment trim cover.


13. REMOVE LUGGAGE COMPARTMENT TRIM HOOK

  1. B125541
    Remove the screw and No. 1 luggage compartment trim hook.


14. REMOVE SIDE LUGGAGE COMPARTMENT TRIM COVER

  1. B125542
    Using a clip remover, remove the 3 clips and side luggage compartment trim cover LH.


15. DISCONNECT LUGGAGE ROOM WIRE

  1. B125544
    Disconnect the No. 3 luggage room wire connector.

  1. Disengage the grommet.


16. REMOVE REAR BUMPER PLATE

  1. B125543
    Using a screwdriver, disengage the 2 claws and remove the No.1 rear bumper plate.

    HINT:
    1. Tape the screwdriver tip before use.
    2. Use the same procedures for the RH side and LH side.


17. REMOVE REAR BUMPER ASSEMBLY

  1. B125545E01
    Put protective tape around the rear bumper assembly.

  1. Using a clip remover, remove the 2 clips.

  1. Remove the 6 screws and 2 rear bumper seal brackets.

  1. B125546
    Disengage the 6 claws and disconnect the rear bumper assembly as shown in the illustration.

    HINT:
    Use the same procedures for the RH side and LH side.

  1. B125547
    Disengage the 4 claws and remove the rear bumper assembly as shown in the illustration.


18. REMOVE NO. 2 ULTRASONIC SENSOR

  1. Disconnect the sensor connector.

  1. E125308
    Remove the sensor retainer as shown in the illustration.

  1. Remove the No. 2 ultrasonic sensor from the rear bumper.


19. REMOVE NO. 1 ULTRASONIC SENSOR

  1. Disconnect the sensor connector.

  1. E075062
    Remove the sensor retainer as shown in the illustration.

  1. Remove the No. 1 ultrasonic sensor from the rear bumper.

← COMPONENTSINSPECTION →