СИСТЕМА ОХЛАЖДЕНИЯ > ПРОВЕРКА БЕЗ СНЯТИЯ С АВТОМОБИЛЯ

для подготовки Нажмите здесь



1. CHECK FOR COOLANT LEAK

ПРИМЕЧАНИЕ:
Before each inspection, turn the A/C switch OFF.

ПРЕДОСТЕРЕЖЕНИЕ:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A148610

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



2. CHECK ENGINE COOLANT LEVEL IN RESERVOIR


    A140929

  1. Check that the engine coolant level is between the LOW and FULL lines when the engine is cold.
    If the engine coolant is below the LOW line, check for leaks and add "TOYOTA Super Long Life Coolant" or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology to the FULL line.

    ПРИМЕЧАНИЕ:
    Do not substitute plain water for engine coolant.



3. CHECK ENGINE COOLANT QUALITY

  1. Remove the radiator reservoir cap.

    ПРЕДОСТЕРЕЖЕНИЕ:
    Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Check if there are any excessive deposits of rust or scales around the radiator cap and radiator filler hole. Also, the coolant should be free of oil.
    If it is excessively dirty, clean the coolant passage and replace the coolant.

  1. Install the radiator reservoir cap.



4. CHECK COOLING FAN SYSTEM

  1. Put the vehicle in the following conditions.

    1. The engine switch is off.

    2. The engine coolant temperature is less than 92°C (198°F).

    3. The battery voltage is between 11 and 14 V.

    4. The A/C switch is OFF.



    A148570E01

  1. Connect the 400 A probe of an ammeter to terminals z3-2 (M+) and z4-2 (S+) of the cooling fan motor.

  1. Turn the engine switch on (IG) and wait for approximately 10 seconds. Check that the fan stops.

  1. Start the engine. Check that the fan stops with the engine idling.

    УКАЗАНИЕ:
    1. Make sure that the engine coolant temperature is less than 92°C (198°F).
    2. Turn the A/C switch OFF.

  1. Check that the fan operates when the A/C switch is turned ON (MAX COOL and the magnet clutch is operating).

    Standard current:

    Item
    		Specified Condition
    No. 1 cooling fan motor
    		2 to 12 A
    No. 2 cooling fan motor
    		2 to 12 A

    УКАЗАНИЕ:
    The engine coolant temperature is less than 92°C (198°F).

  1. Check that the fan operates when the engine coolant temperature sensor connector is disconnected.

    Standard current:

    Item
    		Specified Condition
    No. 1 cooling fan motor
    		2 to 17 A
    No. 2 cooling fan motor
    		2 to 17 A



  1. After the engine is warmed up, check that the fan operates as shown in the illustration below.

    УКАЗАНИЕ:
    1. The engine coolant temperature at which the fan starts operating is approximately 94°C (201°F).
    2. This system can also be checked using the intelligent tester.
    3. Select the following menu items: Power train / Engine / Data List / Initial Engine Coolant Temp.

    A110231E04