СИСТЕМА ПОСАДКИ И ЗАПУСКА > РЕЖИМЫ DATA LIST / ACTIVE TEST

для подготовки Нажмите здесь

УКАЗАНИЕ:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

ПРИМЕЧАНИЕ:

In the table below, the values listed under "Normal Condition" are for reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

1. Connect the intelligent tester to the DLC3.
   

2. Turn the engine switch on (IG).
   

3. Turn the tester on.
   

4. Enter the following menus:
   Select: Body / (desired system) / Data List /
   

5. According to the display on tester, read the "Data List".
   
   

   Main body ECU 

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   IG SW	Engine switch on (IG)/ON or OFF	ON: Engine switch is on (IG) OFF: Engine switch is off	-
   ACC SW	Engine switch on (ACC)/ON or OFF	ON: Engine switch is on (ACC) OFF: Engine switch is off	-
   Start Switch1	Start switch 1/ON or OFF	ON: Engine switch is on (IG) OFF: Engine switch is off	-
   Start Switch2	Start switch 2/ON or OFF	ON: Engine switch is on (IG) OFF: Engine switch is off	-
   Steering Unlock Switch	Steering lock condition/ON or OFF	ON: Steering is unlocked OFF: Steering is locked	-
   Neutral SW/ Clutch SW	Park / neutral position switch/ON or OFF	ON: Shift lever in P or N OFF: Shift lever in R or D	-
   Vehicle Speed Signal	Vehicle speed signal/STOP or RUN	STOP: Vehicle is stopped RUN: Vehicle is running	-
   Engine Condition	Engine condition/STOP or RUN	STOP: Engine is stopped RUN: Engine is running	-
   IG1 Relay Monitor(Outside)	D-IG1 relay outer relay monitor/ON or OFF	ON: Engine switch is on (IG) OFF: Engine switch is off	-
   IG2 Relay Monitor(Outside)	IG2 outer relay monitor/ON or OFF	ON: Engine switch is on (IG) OFF: Engine switch is off	-
   IG1 Relay Monitor(Inside)	D-IG1 relay inner relay monitor/ON or OFF	ON: Engine switch is on (IG) OFF: Engine switch is off	-
   IG2 Relay Monitor(Inside)	IG2 inner relay monitor/ON or OFF	ON: Engine switch is on (IG) OFF: Engine switch is off	-
   ACC Relay Monitor	D-ACC relay monitor/ON or OFF	ON: Engine switch is on (ACC) OFF: Engine switch is off	-
   Ratch Circuit	Ratch circuit/ON or OFF	ON: Engine switch is on (IG) OFF: Engine switch is off, on (ACC) or engine is running	-
   Starter Request Signal	Starter request signal/ON or OFF	ON: ST relay is ON OFF: ST relay is OFF	-
   Power Supply Condition	Power supply condition/ALL, ACC ON, IG1 IG2, ST ON	ALL: All relays are ON ACC ON: D-ACC relay is ON IG1: D-IG1 relay is ON IG2: IG2 relay is ON ST ON: ST relay is ON	-
   Starter Relay Monitor	Starter relay monitor/ON or OFF	ON: Starter relay is ON OFF: Starter relay is OFF	-
   #Codes	Number of diagnosis codes/Min: 0, Max: 255	-	-
   Stop Light SW	Stop light switch/ON or OFF	ON: Brake pedal is depressed OFF: Brake pedal is released	-

   
   

   Certification ECU 

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Ignition Switch	Engine switch/ON or OFF	ON: Engine switch is on (IG) OFF: Engine switch is off	-
   Key Low Battery	Key battery conditions/ON or OFF	ON: Battery is depleted OFF: Battery is not depleted	-
   Unmatch Code or Form	Code format/YES or NO	YES: Code format matches NO: Code format differs	-
   No Response	Response/YES or NO	YES: Response NO: No response	-
   ID Code Difference(Resp)	ID code/YES or NO	YES: ID code matches NO: ID code differs	-
   C Code Difference	Challenge code/YES or NO	YES: Challenge code matches NO: Challenge code differs	-
   Unmatched Vehicle-ID	Key number/YES or NO	YES: Key number matches NO: Key number differs	-
   S Code Check	S code certification result/NG or OK	NG: S code certification result is abnormal OK: S code certification result is normal	-
   L Code Check	L code certification result/NG or OK	NG: L code certification result is abnormal OK: L code certification result is normal	-

   
   

   Rear junction block ECU 

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Stop Light SW	Stop light switch/ON or OFF	ON: Brake pedal depressed OFF: Brake pedal released	-

УКАЗАНИЕ:

Using the intelligent tester to perform the Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

1. Connect the intelligent tester to the DLC3.
   

2. Turn the engine switch on (IG).
   

3. Turn the tester ON.
   

4. Enter the following menus:
   Select: Body / (desired system) / Active Test /
   

5. According to the display on tester, perform the "Active Test".