ОХЛАЖДАЮЩАЯ ЖИДКОСТЬ > ЗАМЕНА

для подготовки Нажмите здесь

1. While using both hands, lift the rear side of the cover upwards to detach the 4 clips B. Slide the cover towards the front of the vehicle to detach the 2 clips labeled A, and remove the V-bank cover.
   

   ПРИМЕЧАНИЕ:

   The V-bank cover may be damaged if its front and rear are lifted at the same time.

1. Remove the 5 clips A.
   

2. Lift up the air cleaner inlet cover to detach the 4 clips B, and remove the cover.
   

1. Remove the 2 bolts.
   

2. Hold the air cleaner inlet by the protrusions A and B, and detach the connections.
   

3. Rotate the No. 1 air cleaner inlet as shown in the illustration to detach the protrusion C.
   

4. Hold the air cleaner inlet by the protrusions D and E, and detach the connections.
   

5. Rotate the No. 1 air cleaner inlet as shown in the illustration to detach the protrusion F.
   

1. Remove the 13 screws, 7 clips and cover.
   

ПРЕДОСТЕРЕЖЕНИЕ:

Do not remove the radiator reservoir cap and vent plug while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

1. Loosen the radiator drain cock plug.
   

   УКАЗАНИЕ:

   Collect the coolant in a container and dispose of it according to the regulations in your area.

2. Remove the radiator reservoir cap, and using a 6 mm hexagon wrench, remove the vent plug.
   

3. Drain coolant.
   

4. Loosen the 2 cylinder block drain cock plugs.
   
   

   
   
   
   

ПРИМЕЧАНИЕ:

Before adding coolant, turn the A/C switch OFF.

Total capacity:

11.8 liters (12.5 US qts, 10.4 Imp. qts)

1. Tighten the radiator drain cock plug and 2 cylinder block drain cock plugs.
   

   Момент затяжки: 

   13 Н*м{ 133 кгс*см , 10 фунт-сила-футов } for cylinder block drain cock plug

2. Add TOYOTA Super Long Life Coolant (SLLC) into the radiator reservoir.
   

   Capacity:

   Approximately 5.0 liters (5.3 US qts, 4.4 Imp. qts)
   

   УКАЗАНИЕ:

   1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
      
   2. Please contact any authorized Toyota dealer, or repairer or another duly qualified and equipped professional for further details.
      
   3. The thermostat open timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the coolant starts to flow inside the hose.
      

3. Further add coolant into the reservoir until it reaches the FULL line.
   

4. Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the coolant level.
   If the coolant level is low, add coolant.
   

5. Using a 6 mm hexagon wrench, install the vent plug.
   

   Момент затяжки: 

   1.5 Н*м{ 15 кгс*см , 13 фунт-сила-дюймов }

6. Bleed air from the cooling system.
   

   ПРИМЕЧАНИЕ:

   Before starting the engine to warm up the engine, turn the A/C switch OFF.

   
   

   1. While idling the engine for approximately 10 minutes, make sure the coolant remains at the FULL line by adding coolant as necessary.
      

   
   
   

   2. After idling the engine for 10 minutes, add coolant until it reaches the B line at the base of the reservoir's filler neck.
      

      Capacity:

      Approximately 2.5 to 3.5 liters (2.6 to 3.7 US qts, 2.2 to 3.1 Imp. qts)
      

      УКАЗАНИЕ:

      The B line is the lower edge of the inner wall of the filler neck.

   3. Close the radiator reservoir cap, and run the engine at 1500 to 2000 rpm for 5 minutes.
      

      УКАЗАНИЕ:

      The thermostat open timing can be confirmed by pressing the No. 1 radiator hose by hand, and checking when the SLLC starts to flow inside the hose.

      ПРЕДОСТЕРЕЖЕНИЕ:

      When pressing the radiator hose:

      1. Wear protective gloves.
         
      2. Be careful as the radiator hose is hot.
         
      3. Keep your hands away from the radiator fan.
         

7. Stop the engine and wait until the coolant cools down to ambient temperature.
   

   ПРЕДОСТЕРЕЖЕНИЕ:

   Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot coolant and steam may be released and cause serious burns.

8. Check the coolant level.
   If the coolant level is below the FULL line, add coolant until it reaches the FULL line.
   

ПРИМЕЧАНИЕ:

Before each inspection, turn the A/C switch OFF.

ПРЕДОСТЕРЕЖЕНИЕ:

Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

1. Fill the radiator with coolant and attach a radiator cap tester.
   

2. Warm up the engine.
   

3. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm², 17 psi), and check that the pressure does not drop.
   If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.
   

1. Align the holes with the connection areas labeled A, and attach the No. 1 air cleaner inlet.
   

2. Install the No. 1 air cleaner inlet with the 2 bolts.
   

   Момент затяжки: 

   5.0 Н*м{ 51 кгс*см , 44 фунт-сила-дюймов }

1. Attach the 4 clips B.
   

   ПРИМЕЧАНИЕ:

   1. Make sure the clips are attached securely.
      
   2. Attaching the clips forcefully or hitting the top of the clips may damage them.
      

2. Install the air cleaner inlet cover with the 5 clips A.
   

1. After sliding the cover from the vehicle front to the rear to attaching the 2 clips A, attach the 4 clips B and install the V bank cover.
   

   ПРИМЕЧАНИЕ:

   1. Make sure the clips are attached securely.
      
   2. Attaching the clips forcefully or hitting the top of the clips may damage them.
      

1. Install the cover with the 7 clips and 13 screws.