ЦЕПНОЙ ПРИВОД ГАЗОРАСПРЕДЕЛИТЕЛЬНОГО МЕХАНИЗМА > УСТАНОВКА

для подготовки Нажмите здесь

1. Install the chain tensioner with the 2 bolts.
   

   Момент затяжки: 

   10 Н*м{ 102 кгс*см , 7 фунт-сила-футов }

2. While raising up the No. 2 chain tensioner, insert a pin of φ1.0 mm (0.039 in.) into the hole to fix it in place.
   

1. Align the No. 1 chain's orange mark plates with the camshaft timing gear's timing mark, and attach the chain to the gear as shown in the illustration.
   

2. Align the No. 1 chain's orange mark plate with the crankshaft timing gear's timing mark, and attach the chain to the gear as shown in the illustration.
   

3. Align the No. 2 chain's mark plates (yellow) with the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly, and attach the No. 2 chain to the gears as shown in the illustration.
   

   УКАЗАНИЕ:

   The crankshaft timing gear and camshaft exhaust gear assembly will be installed with the No. 1 and No. 2 chains connected to the gears.

4. Install the crankshaft timing gear to the crankshaft.
   

5. Align and attach the knock pin of the No. 1 camshaft with the pin hole of the camshaft timing gear assembly.
   

6. Using the hexagonal portion of the No. 2 camshaft, align and attach the knock pin of the No. 2 camshaft with the pin hole of the camshaft timing exhaust gear assembly.
   

7. Remove the pin from the No. 2 chain tensioner.
   

1. Install the vibration damper with the 2 bolts.
   

   Момент затяжки: 

   21 Н*м{ 214 кгс*см , 15 фунт-сила-футов }

УКАЗАНИЕ:

If you cannot install the chain tensioner slipper due to the tension of the chain, use the hexagonal portion of the camshaft to loosen the chain, and then install the chain tensioner slipper.

1. Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
   

2. Move the stopper plate downward to set the lock, and insert a hexagon wrench into the hole of the stopper plate.
   

3. Install the chain tensioner with the 2 bolts.
   

   Момент затяжки: 

   10 Н*м{ 102 кгс*см , 7 фунт-сила-футов }

4. Remove the hexagon wrench from the chain tensioner.
   

1. Install the chain tensioner with the 2 bolts.
   

   Момент затяжки: 

   10 Н*м{ 102 кгс*см , 7 фунт-сила-футов }

2. While pushing down the No. 2 chain tensioner, insert a pin of φ1.0 mm (0.039 in.) into the hole to fix it in place.
   

1. Align the No. 1 chain's orange mark plates with the camshaft timing gear's timing mark, and attach the chain to the gear as shown in the illustration.
   

2. Align the No. 1 chain's orange mark plate with the crankshaft timing gear's timing mark, and attach the chain to the gear as shown in the illustration.
   

3. Align the No. 2 chain's mark plates (yellow) with the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly, and attach the No. 2 chain to the gears as shown in the illustration.
   

   УКАЗАНИЕ:

   The crankshaft timing gear and camshaft exhaust gear assembly will be installed with the No. 1 and No. 2 chains connected to the gears.

4. Install the crankshaft timing gear to the crankshaft.
   

5. Align and attach the knock pin of the No. 3 camshaft with the pin hole of the camshaft timing gear assembly.
   

6. Using the hexagonal portion of the No. 4 camshaft, align and attach the knock pin of the No. 4 camshaft with the pin hole of the camshaft timing exhaust gear assembly.
   

   ПРИМЕЧАНИЕ:

   Because the gears' timing mark positions may shift due to looseness of the No. 1 chain, use the hexagonal portion of the camshaft to hold the No. 3 camshaft in place until the No. 1 chain tensioner is installed.

7. Remove the pin from the No. 2 chain tensioner.
   

УКАЗАНИЕ:

If you cannot install the chain tensioner slipper due to the tension of the chain, use the hexagonal portion of the camshaft to loosen the chain and install the chain tensioner.

1. Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
   

2. Move the stopper plate downward to set the lock, and insert a hexagon wrench into the hole of the stopper plate.
   

3. Install a new gasket and chain tensioner with the 2 bolts.
   

   Момент затяжки: 

   10 Н*м{ 102 кгс*см , 7 фунт-сила-футов }

1. Install the vibration damper with the 2 bolts.
   

   Момент затяжки: 

   21 Н*м{ 214 кгс*см , 15 фунт-сила-футов }

2. Remove the hexagon wrench from the No. 1 chain tensioner.
   

1. for Bank 1:
   
   

   
   
   

   1. Using a wrench, hold the hexagonal portion of the No. 3 camshaft.
      

   2. Using a 12 mm socket hexagon wrench, tighten the camshaft timing gear assembly with a new bolt.
      

      Момент затяжки: 

      79 Н*м{ 806 кгс*см , 58 фунт-сила-футов }

   
   
   

   3. Using a wrench to hold the hexagonal portion of the No. 4 camshaft, tighten the camshaft timing exhaust gear assembly with the bolt.
      

      Момент затяжки: 

      100 Н*м{ 1020 кгс*см , 74 фунт-сила-футов }

2. for Bank 2:
   
   

   
   
   

   1. Using a wrench, hold the hexagonal portion of the No. 1 camshaft.
      

   2. Using a 12 mm socket hexagon wrench, tighten the camshaft timing gear assembly with a new bolt.
      

      Момент затяжки: 

      79 Н*м{ 806 кгс*см , 58 фунт-сила-футов }

   
   
   

   3. Using a wrench to hold the hexagonal portion of the No. 2 camshaft, tighten the camshaft timing exhaust gear assembly with the bolt.
      

      Момент затяжки: 

      100 Н*м{ 1020 кгс*см , 74 фунт-сила-футов }

1. Temporarily install the crankshaft pulley bolt.
   

2. Rotate the crankshaft clockwise, and check that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.
   

3. Remove the crankshaft pulley bolt.
   
   

   
   
   
   

1. Install the timing chain cover (see page Нажмите здесь).