ВПУСКНОЙ КОЛЛЕКТОР > СНЯТИЕ

для подготовки Нажмите здесь

1. Remove the 6 clips and cowl top ventilator louver RH.
   

ПРЕДОСТЕРЕЖЕНИЕ:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

1. While using both hands, lift the rear side of the cover upwards to detach the 4 clips B. Slide the cover towards the front of the vehicle to detach the 2 clips labeled A, and remove the V-bank cover.
   

   ПРИМЕЧАНИЕ:

   The V-bank cover may be damaged if its front and rear are lifted at the same time.

1. Remove the 5 clips A.
   

2. Lift up the air cleaner inlet cover to detach the 4 clips B, and remove the cover.
   

1. Remove the 4 clips and engine room side cover.
   

1. Remove the 2 bolts.
   

2. Hold the air cleaner inlet by the protrusions A and B, and detach the connections.
   

3. Rotate the No. 1 air cleaner inlet as shown in the illustration to detach the protrusion C.
   

4. Hold the air cleaner inlet by the protrusions D and E, and detach the connections.
   

5. Rotate the No. 1 air cleaner inlet as shown in the illustration to detach the protrusion F.
   

1. Remove the 13 screws, 7 clips and cover.
   

1. Remove the 8 bolts and suspension member protector.
   

1. Remove the 8 bolts and under cover.
   

ПРЕДОСТЕРЕЖЕНИЕ:

Do not remove the radiator reservoir cap and vent plug while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

1. Loosen the radiator drain cock plug.
   

   УКАЗАНИЕ:

   Collect the coolant in a container and dispose of it according to the regulations in your area.

2. Remove the radiator reservoir cap, and using a 6 mm hexagon wrench, remove the vent plug.
   

3. Drain coolant.
   

4. Loosen the 2 cylinder block drain cock plugs.
   
   

   
   
   
   

1. Disconnect the No. 1 ventilation hose and No. 2 ventilation hose from the intake air connector pipe.
   

2. Loosen the 3 hose clamps, and remove the intake air connector pipe.
   

1. Disconnect the throttle motor connector.
   

2. Remove the 4 bolts and throttle body.
   

3. Slide the clamps, and disconnect the No. 4 and No. 5 water by-pass hoses from the throttle body.
   

4. Remove the gasket from the intake manifold.
   

1. Disconnect the MAF meter connector.
   

2. Disconnect the 2 clamps and air cleaner cap.
   

3. Remove the air cleaner element from air cleaner case.
   

4. Remove the 2 nuts, clip and air cleaner case.
   

1. Disconnect the MAF meter connector.
   

2. Disconnect the 2 clamps and air cleaner cap.
   

3. Remove the air cleaner element from air cleaner case.
   

4. Remove the 2 nuts, clip and air cleaner case.
   

УКАЗАНИЕ:

Fix the disconnected harnesses, etc. with tape or equivalent so that they do not interfere.

1. Disconnect the engine wire harness connector.
   

2. Remove the nut, and disconnect the +B terminal of the generator assembly.
   

3. Using a clip remover, disconnect the 6 engine wire harness clamps.
   

4. Remove the nut, and disconnect the engine wire from the fusible link block assembly.
   

5. Remove the bolt, and disconnect the engine wire harness ground side.
   

6. Remove the 3 bolts and 3 engine wire harness clamp brackets.
   

7. Remove the 4 nuts, and disconnect the engine wire harness.
   
   

   
   
   
   

1. Slide the 4 clamps, and disconnect the heater water inlet hose, heater water outlet hose, water inlet hose, and No. 3 water by-pass hose from the water by-pass pipe sub-assembly.
   

2. Remove the 2 bolts and water by-pass pipe.
   

1. Disconnect the fuel vapor feed hose and No. 2 fuel vapor feed hose.
   

2. Remove the bolt and vacuum switching valve.
   

1. Disconnect the No. 1 ventilation hose from the intake manifold.
   

2. Remove the 8 bolts, 2 nuts and intake manifold.
   

3. Remove the 2 gaskets from the intake manifold.