ЭЛЕКТРОДВИГАТЕЛЬ МЕХАНИЗМА ИЗМЕНЕНИЯ ФАЗ ГАЗОРАСПРЕДЕЛЕНИЯ > УСТАНОВКА

для подготовки Нажмите здесь



1. INSTALL CAMSHAFT TIMING CONTROL MOTOR LH


    A150415E01

  1. Turn the camshaft timing gear assembly's eccentric shaft index slot in the counterclockwise direction by hand, and set it to the maximum retard angle position.

    УКАЗАНИЕ:
    1. When the cam of the camshaft lifts the valve, the eccentric shaft becomes difficult to turn.
    2. The position where the eccentric shaft stops is the maximum retard angle.

  1. Install a new O-ring to the timing chain cover.



    A145594E01

  1. Align the joint of the camshaft timing control motor and the keyway of the camshaft timing gear assembly, and install the motor with the 3 bolts.

    Момент затяжки: 
    21 Н*м{ 214 кгс*см , 15 фунт-сила-футов }

    ПРИМЕЧАНИЕ:
    1. Check that [L] is printed on the label of the camshaft timing control motor.
    2. Do not allow foreign matter to contact the oil seal face of the camshaft timing control motor (connecting surface with timing chain cover sub-assembly).
    3. When installing the camshaft timing control motor, do not use excessive force.
    4. Align the timing chain cover sub-assembly knock pin with the camshaft timing control motor pin hole to install the camshaft timing control motor.
    5. Install the camshaft timing control motor with the arrow facing upward, as shown in the illustration.
    6. Do not drop the camshaft timing control motor. If dropped, replace it.
    7. Do not disassemble the camshaft timing control motor assembly. If disassembled, replace it.



    A149390

  1. Connect the 2 camshaft timing control motor connectors and engine wire clamp.



2. INSTALL CAMSHAFT TIMING CONTROL MOTOR RH


    A150416E01

  1. Turn the camshaft timing gear assembly's eccentric shaft index slot in the counterclockwise direction by hand, and set it to the maximum retard angle position.

    УКАЗАНИЕ:
    1. When the cam of the camshaft lifts the valve, the eccentric shaft becomes difficult to turn.
    2. The position where the eccentric shaft stops is the maximum retard angle.

  1. Install a new O-ring to the timing chain cover.



    A145593E01

  1. Align the joint of the camshaft timing control motor and the keyway of the camshaft timing gear assembly, and install the motor with the 3 bolts.

    Момент затяжки: 
    21 Н*м{ 214 кгс*см , 15 фунт-сила-футов }

    ПРИМЕЧАНИЕ:
    1. Check that [R] is printed on the label of the camshaft timing control motor.
    2. Do not allow foreign matter to contact the oil seal face of the camshaft timing control motor (connecting surface with timing chain cover sub-assembly).
    3. When installing the camshaft timing control motor, do not use excessive force.
    4. Align the timing chain cover sub-assembly knock pin with the camshaft timing control motor pin hole to install the camshaft timing control motor.
    5. Install the camshaft timing control motor with the arrow facing upward, as shown in the illustration.
    6. Do not drop the camshaft timing control motor. If dropped, replace it.
    7. Do not disassemble the camshaft timing control motor assembly. If disassembled, replace it.



    A149389

  1. Install the engine wire bracket with the bolt.

    Момент затяжки: 
    10 Н*м{ 102 кгс*см , 7 фунт-сила-футов }

  1. Connect the 2 camshaft timing control motor connectors.



3. INSTALL INTAKE AIR CONNECTOR PIPE


A148828E01

  1. Align the protrusion of the intake air resonator with the cutout of the bracket and insert the protrusion.

  1. Install the intake air connector pipe with the 3 hose clamps.

    Момент затяжки: 
    4.8 Н*м{ 48 кгс*см , 42 фунт-сила-дюймов } for intake air connector pipe and throttle body
    3.8 Н*м{ 38 кгс*см , 34 фунт-сила-дюймов } for intake air connector pipe and intake air resonator

    ПРИМЕЧАНИЕ:
    Insert the protrusion of the intake air connector pipe into the hole of the hose clamp.

    УКАЗАНИЕ:
    1. The intake air connector pipe and throttle body can be tightened within the range of 4.0 N*m (41 kgf*cm. 35 in.*lbf) to 5.5 N*m (56 kgf*cm. 49 in.*lbf), and the intake air connector pipe and air cleaner assembly can be tightened within the range of 2.0 N*m (20 kgf*cm. 18 in.*lbf) to 5.5 N*m (56 kgf*cm. 49 in.*lbf).
    2. When tightening the hose clamp, make sure the hose clamp's end is within the painted white line (width: 2 mm).



    A148829E01

  1. Connect the No. 1 ventilation hose and No. 2 ventilation hose to the intake air connector pipe.

    ПРИМЕЧАНИЕ:
    1. Position the claws of the clamps as shown in the illustration.
    2. Install the clips so that they are within the hose's paint marks.



4. INSTALL NO. 1 AIR CLEANER INLET


A158334E01

  1. Align the holes with the connection areas labeled A, and attach the No. 1 air cleaner inlet.



    A148822

  1. Install the No. 1 air cleaner inlet with the 2 bolts.

    Момент затяжки: 
    5.0 Н*м{ 51 кгс*см , 44 фунт-сила-дюймов }



5. INSTALL AIR CLEANER INLET COVER SUB-ASSEMBLY


A148821E01

  1. Attach the 4 clips B.

    ПРИМЕЧАНИЕ:
    1. Make sure the clips are attached securely.
    2. Attaching the clips forcefully or hitting the top of the clips may damage them.

  1. Install the air cleaner inlet cover with the 5 clips A.



6. INSTALL V-BANK COVER SUB-ASSEMBLY


A148820E01

  1. After sliding the cover from the vehicle front to the rear to attaching the 2 clips A, attach the 4 clips B and install the V bank cover.

    ПРИМЕЧАНИЕ:
    1. Make sure the clips are attached securely.
    2. Attaching the clips forcefully or hitting the top of the clips may damage them.



7. REMOVE COWL TOP VENTILATOR LOUVER RH


E139771

  1. Remove the 6 clips and cowl top ventilator louver RH.



8. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

ПРЕДОСТЕРЕЖЕНИЕ:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

УКАЗАНИЕ:
Disconnect the cable from the negative battery terminal so that the maximum retard angle of the camshaft timing control motor assembly will be learned.



9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


10. INSTALL COWL TOP VENTILATOR LOUVER RH


E139771

  1. Install the 6 clips and cowl top ventilator louver RH.

    ПРИМЕЧАНИЕ:
    If the cowl top ventilator louver RH is not properly installed, water may leak into the engine room and cause malfunctions. Therefore, make sure the cowl top ventilator louver RH is installed properly.



11. PERFORM INITIALIZATION

  1. Perform initialization (see page Нажмите здесь).

    ПРИМЕЧАНИЕ:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.