Last Modified: 4-30-2014 6.6 C Doc ID: RM000000T8M00NX
Model Year: 2006 Model: LX470 Prod Date Range: [05/2005 -           ]
Title: 2UZ-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0505; Idle Control System Malfunction; 2006 MY LX470 [05/2005 -        ]

DTC

P0505

Idle Control System Malfunction

DESCRIPTION

The idle speed is controlled by the Electronic Throttle Control System (ETCS). The ETCS is comprised of: 1) one valve type throttle body; 2) the throttle actuator, which operates the throttle valve; 3) the throttle position sensor, which detects the opening angle of the throttle valve; 4) the accelerator pedal position sensor, which detects the accelerator pedal position; and 5) the ECM, which controls the ETCS. Based on the target idle speed, the ECM controls the throttle actuator to provide the proper throttle valve opening angle.

DTC No.

DTC Detection Condition

Trouble Area

P0505

Idle speed continues to vary greatly from target speed (2 trip detection logic)
  • ETCS
  • Air induction system
  • Ventilation hose connection
  • ECM

MONITOR DESCRIPTION

The ECM detects idle speed and idle air flow amount for Idle Speed Control (ISC). The ECM concludes that the ISC is malfunctioning if: 1) the learned value of the ISC remains at the maximum or minimum 5 times or more during a drive cycle, and 2) while driving at 10 km/h (6 mph) or more, the actual idle RPM varies from the target RPM by between 100 to 200 RPM 5 times or more during a drive cycle.

Example:

If the actual idle RPM varies from the target idle RPM by more than 200 rpm* 5 times during a drive cycle, the ECM will turn on the MIL and a DTC is set.

HINT:

*: RPM threshold varies with engine load.

MONITOR STRATEGY

Related DTCs

P0505: IAC functional check

P0505: IAC range check

Required Sensors/Components (Main)

ETCS

Required Sensors/Components (Related)

Crankshaft position sensor, ECT sensor, Vehicle speed sensor

Frequency of Operation

Continuous

Duration

10 minutes: IAC functional check

MIL Operation

2 drive cycles: IAC functional check

Sequence of Operation

None

TYPICAL ENABLING CONDITIONS

Monitor will run whenever these DTCs are not present

None

Engine

Running

TYPICAL MALFUNCTION THRESHOLDS

1. Frequency that both of following conditions (a) and (b) are met

5 times or more

(a) Engine RPM - Target engine RPM (A/C OFF and NSW OFF)

Less than -100 rpm, or more than 150 rpm

(b) Vehicle condition

Stop after vehicle was driven at 10 km/h (6 mph) or more

2. Frequency that both of following conditions (a) and (b) are met

Once

(a) Engine RPM - Target engine RPM (A/C OFF and NSW OFF)

Less than -100 rpm, or more than 150 rpm

(b) IAC flow rate learning value

2.48 L/sec or less. or 11 L/sec

INSPECTION PROCEDURE

HINT:

  • The detection of DTC P0505 may also be caused by: 1) the floor carpet overlapping onto the accelerator pedal, causing the accelerator pedal to be slightly depressed (throttle position to be slightly open); or 2) the accelerator pedal not being fully released.
  • Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.

CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0505)

(a) Connect the intelligent tester to the CAN VIM. Then connect the CAN VIM to the DLC3.

(b) Turn the ignition switch ON.

(c) Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.

(d) Read the DTCs.

HINT:

If any other codes besides P0101 are output, perform troubleshooting for those DTCs first.

Display (DTC output)

Proceed to

P0505

A

P0505 and other DTCs

B

HINT:

If any DTCs other than P0505 are output, troubleshoot those DTCs first.

B

GO TO RELEVANT DTC CHART

A

2.

CHECK CONNECTION OF VENTILATION HOSE

OK:

Ventilation hose is connected correctly and is not damaged.

NG

REPAIR OR REPLACE VENTILATION HOSE

OK

3.

CHECK AIR INDUCTION SYSTEM

(a) Check for vacuum leaks in the air induction system.

OK:

No leakage from air induction system.

NG

REPAIR OR REPLACE AIR INDUCTION SYSTEM

OK

4.

CHECK THROTTLE VALVE

(a) Check the throttle valve condition.

NG

REPLACE THROTTLE BODY

OK

REPLACE ECM