A750F AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMISSION SYSTEM: P0781; 1-2 Shift (1-2 Shift Valve); 2006 MY LX470 [05/2005

Last Modified: 4-30-2014	6.6 C	Doc ID: RM000000XP100GX
Model Year: 2006	Model: LX470	Prod Date Range: [05/2005 - ]
Title: A750F AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMISSION SYSTEM: P0781; 1-2 Shift (1-2 Shift Valve); 2006 MY LX470 [05/2005 - ]

DTC

P0781

1-2 Shift (1-2 Shift Valve)

DESCRIPTION

The 1-2 shift valve performs shifting to 1st gear and other gears.

DTC No.	DTC Detection Condition	Trouble Area
P0781	Gear required by the ECM does not match the actual gear when driving (2 trip detection logic)	Valve body is blocked up or stuck (1-2 shift valve) Automatic transmission (clutch, brake or gear, etc.)

MONITOR DESCRIPTION

This DTC indicates that the 1-2 shift valve in the valve body is locked in the direction that the spring compresses.

The ECM commands gear shifts by turning the shift solenoid valves ON/OFF and switching oil pressure to the valves in the valve body.

The ECM calculates the actual transmission gear by comparing the signals from the input speed sensor (NT) and the output speed sensor (SP2). The ECM can detect mechanical problems in the shift solenoids, valve body and automatic transmission (clutch, brakes, gears, etc.). If the ECM detects that the actual gear position and the commanded gear position are different, it will illuminate the MIL and store the DTC.

MONITOR STRATEGY

Related DTCs	P0781: Valve body/Rationality check
Required sensors/Components	Valve body, Automatic transmission assembly, Speed sensor (NT), Speed sensor (NO), Vehicle speed sensor, Throttle position sensor
Frequency of operation	Continuous
Duration	Condition (A), and (B) 0.4 sec. Condition (C) 3 sec. Condition (D) 0.5 sec.
MIL operation	2 driving cycles
Sequence of operation	None

TYPICAL ENABLING CONDITIONS

The following conditions are common to all conditions below: Condition (A), (B), (C), and (D)

The monitor will run whenever this DTC is not present.	None
Turbine speed sensor (NT) circuit	Not circuit malfunction
Output speed sensor (NO) circuit	Not circuit malfunction
Shift solenoid valve S1 circuit	Not circuit malfunction
Shift solenoid valve S2 circuit	Not circuit malfunction
Shift solenoid valve SR circuit	Not circuit malfunction
Shift solenoid valve SL1 circuit	Not circuit malfunction
Shift solenoid valve SL2 circuit	Not circuit malfunction
ECT (Engine coolant temperature) sensor circuit	Not circuit malfunction
KCS sensor circuit	Not circuit malfunction
ETCS (Electric throttle control system)	Not system down
Transmission range	"D"
ECT	40°C (104°F) or more
Spark advance from Max. retard timing by KCS control	0°crankshaft angle or more
Engine	Starting
Transfer range	"HIGH" *

Transfer range "HIGH" * (This condition is applied only 4WD)

* Following conditions met

Vehicle speed sensor "A" circuit	Not circuit malfunction
Output shaft speed sensor circuit	Not circuit malfunction
Transfer output speed	143 rpm or more
NO/NOtf (Transfer input speed/Transfer output speed)	0.9 to 1.1

Condition (A)

ECM selected gear	2nd
Vehicle speed	2 km/h (1.2 mph) or more
Output speed	2nd → 1st down shift point or more
Throttle valve opening angle	7% or more at 2,000 rpm (Conditions vary with engine speed)
Calculated load value	7.75% or more

Condition (B)

ECM selected gear	4th
Vehicle speed	2 km/h (1.2 mph) or more
Throttle valve opening angle	7% or more at 2,000 rpm (Conditions vary with engine speed)
Calculated load value	7.75% or more

Condition (C)

Current ECM selected gear

5th

Last ECM selected gear

4th

Vehicle speed

(During transition from 4th to 5th gear)

Less than 100 km/h (62.2 mph)

Condition (D)

ECM selected gear

5th

Engine speed - Turbine speed (NE - NT)

(After transition from 4th to 5th gear)

Less than 150 rpm

Vehicle speed

(After transition from 4th to 5th gear)

Less than 100 km/h (62.2 mph)

TYPICAL MALFUNCTION THRESHOLDS

Both of the following conditions are met: (A), and Condition (B), (C) or (D)

Malfunction (A)

Turbine speed/Output speed (NT/NO)

3.30 or more, and 7.50 or less

(This means actual gear is 1st)

Malfunction (B)

Turbine speed/Output speed (NT/NO)

1.28 or more, and 1.53 or less

(This means actual gear is 3rd)

Malfunction (C)

Turbine speed - Output speed x 4th gear ratio

(NT - NO x 4th gear ratio)

1,000 rpm or more

Malfunction (D)

Turbine speed - Output speed x 5th gear ratio

(NT - NO x 5th gear ratio)

1,000 rpm or more

INSPECTION PROCEDURE

PROCEDURE

1.	CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0781)

(a) Connect the intelligent tester to the CAN VIM. Then connect the CAN VIM to the DLC3.

(b) Turn the ignition switch ON and push the intelligent tester main switch ON.

(d) Read the DTCs using the intelligent tester.

Display (DTC output)	Proceed to
Only P0781 is output	A
P0781 and other DTCs	B

HINT:

If any other codes besides P0781 are output, perform troubleshooting for those DTCs first.

GO TO DTC CHART

2.	PERFORM ACTIVE TEST BY INTELLIGENT TESTER

HINT:

Performing the intelligent tester's ACTIVE TEST allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the ACTIVE TEST early in troubleshooting is one way to save time.

The DATA LIST can be displayed during the ACTIVE TEST.

(a) Warm up the engine.

(b) Turn the ignition switch OFF.

(d) Turn the ignition switch ON.

(e) Turn the intelligent tester ON.

(f) Enter the following menus: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST.

(g) Read the ACTIVE TEST using the intelligent tester.

HINT:

While driving, the shift position can be forcibly changed with the intelligent tester.

Comparing the shift position commanded by the ACTIVE TEST with the actual shift position enables you to confirm the problem .

Item

Test Details

Diagnostic Note

SHIFT

[Test Details]

Operate the shift solenoid valve and set each shift position by yourself

[Vehicle Condition]

IDL: ON
Less than 50 km/h (31 mph)

[Other information]

Press "→" button: Shift up
Press "←" button: Shift down

Possible to check the operation of the shift solenoid valves

HINT:

This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.
The 4th to 5th up-shift must be performed with the accelerator pedal released.
The 5th to 4th down-shift must be performed with the accelerator pedal released.
Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
The shift position commanded by the ECM is shown in the DATA LIST (shift status) display on the intelligent tester.

OK:

Gear position changes in accordance with the tester command.

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

3.	CLEAR DTC AND PERFORM RUNNING TEST

(a) Clear the DTC, and check for the DTC again after conducting the "Test Monitor Drive Pattern for ECT" .

OK:

No DTC code

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

END