Companion flange vertical runout

Maximum: 0.14 mm (0.0055 in.)

Companion flange lateral runout

Maximum: 0.14 mm (0.0055 in.)

Drive pinion preload (at start of torque)

New bearing: 1.1 to 1.6 N*m (11 to 16 kgf*cm, 9.7 to 13.9 in.*lbf)

Reused bearing: 0.6 to 0.9 N*m (6 to 9 kgf*cm, 5.3 to 8.0 in.*lbf)

Total preload (at start of torque) + drive pinion preload

0.4 to 0.6 N*m (4 to 6 kgf*cm, 3.5 to 5.3 in.*lbf)

Ring gear runout

Maximum: 0.07 mm (0.0028 in.)

Ring gear backlash

0.13 mm to 0.18 (0.0051 to 0.0071 in.)

Side gear backlash

0.05 mm to 0.20 (0.0020 to 0.0079 in.)

Differential case runout

Maximum: 0.07 mm (0.0028 in.)

Differential oil seal drive in depth

1.5 mm (0.0059 in.)

Side gear thrust washer thickness

0.9 mm (0.035 in.)

1.0 mm (0.039 in.)

1.1 mm (0.043 in.)

1.2 mm (0.047 in.)

1.3 mm (0.051 in.)

Side bearing adjusting washer thickness

2.58 mm (0.1016 in.)

2.60 mm (0.1024 in.)

2.62 mm (0.1031 in.)

2.64 mm (0.1039 in.)

2.66 mm (0.1047 in.)

2.68 mm (0.1055 in.)

2.70 mm (0.1063 in.)

2.72 mm (0.1071 in.)

2.74 mm (0.1079 in.)

2.76 mm (0.1087 in.)

2.78 mm (0.1094 in.)

2.80 mm (0.1102 in.)

2.82 mm (0.1110 in.)

2.84 mm (0.1118 in.)

2.86 mm (0.1126 in.)

2.88 mm (0.1134 in.)

2.90 mm (0.1142 in.)

2.92 mm (0.1150 in.)

2.94 mm (0.1157 in.)

2.96 mm (0.1165 in.)

2.98 mm (0.1173 in.)

3.00 mm (0.1181 in.)

3.02 mm (0.1189 in.)

3.04 mm (0.1197 in.)

3.06 mm (0.1205 in.)

3.08 mm (0.1213 in.)

3.10 mm (0.1220 in.)

3.12 mm (0.1228 in.)

3.14 mm (0.1236 in.)

3.16 mm (0.1244 in.)

3.18 mm (0.1252 in.)

3.20 mm (0.1260 in.)

3.22 mm (0.1268 in.)

3.24 mm (0.1276 in.)

3.26 mm (0.1283 in.)

3.28 mm (0.1291 in.)

3.30 mm (0.1299 in.)

3.32 mm (0.1307 in.)

3.34 mm (0.1315 in.)

3.36 mm (0.1323 in.)

3.38 mm (0.1331 in.)

3.40 mm (0.1339 in.)

3.42 mm (0.1346 in.)

3.44 mm (0.1354 in.)

3.46 mm (0.1362 in.)

3.48 mm (0.1370 in.)

Drive pinion bearing adjust washer thickness

1.70 mm (0.067 in.)

1.73 mm (0.068 in.)

1.76 mm (0.069 in.)

1.79 mm (0.070 in.)

1.82 mm (0.072 in.)

1.85 mm (0.073 in.)

1.88 mm (0.074 in.)

1.91 mm (0.075 in.)

1.94 mm (0.076 in.)

1.97 mm (0.078 in.)

2.00 mm (0.079 in.)

2.03 mm (0.080 in.)

2.06 mm (0.081 in.)

2.09 mm (0.082 in.)

2.12 mm (0.083 in.)

2.15 mm (0.085 in.)

2.18 mm (0.086 in.)

2.21 mm (0.087 in.)

2.24 mm (0.088 in.)

2.27 mm (0.089 in.)

2.30 mm (0.091 in.)

2.33 mm (0.092 in.)

Companion flange vertical runout

Maximum: 0.14 mm (0.0055 in.)

Companion flange lateral runout

Maximum: 0.14 mm (0.0055 in.)

Drive pinion preload (at start of torque)

New bearing: 1.36 to 1.90 N*m (13.9 to 19.4 kgf*cm, 12.0 to 16.8 in.*lbf)

Reused bearing: 0.71 to 0.99 N*m (7.2 to 10.1 kgf*cm, 6.3 to 8.8 in.*lbf)

Total preload (at start of torque) + drive pinion preload

0.38 to 0.63 N*m (3.9 to 6.5 kgf*cm, 3.3 to 5.6 in.*lbf)

Ring gear runout

Maximum: 0.05 mm (0.0020 in.)

Ring gear backlash

0.13 to 0.18 mm (0.0051 to 0.0071 in.)

Side gear backlash

0.02 to 0.15 mm (0.0008 to 0.0059 in.)

Differential case runout

Maximum: 0.04 mm (0.0016 in.)

Rear differential front oil seal drive in depth

0.05 mm (0.0020 in.)

Side gear thrust washer thickness

1.55 mm (0.061 in.)

1.60 mm (0.063 in.)

1.65 mm (0.065 in.)

1.70 mm (0.067 in.)

1.75 mm (0.069 in.)

1.80 mm (0.071 in.)

1.85 mm (0.073 in.)

1.90 mm (0.075 in.)

1.95 mm (0.077 in.)

2.00 mm (0.079 in.)

2.05 mm (0.081 in.)

2.10 mm (0.083 in.)

Tooth contact pattern adjust washer thickness

1.050 mm (0.04134 in.)

1.075 mm (0.04232 in.)

1.100 mm (0.04331 in.)

1.125 mm (0.04429 in.)

1.150 mm (0.04528 in.)

1.175 mm (0.04626 in.)

1.200 mm (0.04724 in.)

1.225 mm (0.04823 in.)

1.250 mm (0.04921 in.)

1.275 mm (0.05020 in.)

1.300 mm (0.05118 in.)

1.325 mm (0.05217 in.)

1.350 mm (0.05315 in.)

1.375 mm (0.05413 in.)

1.400 mm (0.05512 in.)

1.425 mm (0.05610 in.)

1.450 mm (0.05709 in.)

1.475 mm (0.05807 in.)

1.500 mm (0.05906 in.)

1.525 mm (0.06004 in.)

1.550 mm (0.06102 in.)