| Last Modified: 7-3-2017 | 6.8:8.0.40 | Doc ID: RM00000185T001X |
| Model Year Start: 2007 | Model: LX470 | Prod Date Range: [08/2006 - ] |
| Title: ENGINE IMMOBILISER: ENGINE IMMOBILISER SYSTEM: DATA LIST / ACTIVE TEST; 2007 MY LX470 [08/2006 - ] | ||
DATA LIST / ACTIVE TEST
1. READ DATA LIST
HINT:
Using the intelligent tester's DATA LIST allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the DATA LIST early in troubleshooting is one way to save time.
(a) Connect the intelligent tester (with CAN VIM) to the DLC3.
(b) Turn the ignition switch ON.
(c) Read the DATA LIST by following the directions on the tester screen.
Transponder key ECU assembly:
|
Item |
Measurement Item / Display (Range) |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
IG SW |
Ignition switch signal / ON or OFF |
OFF: Ignition switch OFF or ACC ON: Ignition switch ON |
- |
|
KEY SW |
Unlock warning switch signal / ON or OFF |
OFF: No key is in ignition key cylinder ON: Key is in ignition key cylinder |
|
|
+B |
+B judgment / NORMAL or BREAK |
NORMAL: Battery supply is normal BREAK: Battery supply is malfunctioning |
|
|
ANTENNA COIL |
Transponder key coil condition / NORMAL or FAIL |
NORMAL: Transponder key coil is normal FAIL: Transponder key coil is malfunctioning |
|
|
IMMOBILISER |
Immobiliser system status / SET or UNSET |
UNSET: Ignition switch ON SET: No key is in ignition key cylinder |
|
|
MASTER KEY |
Master key code signal / NOMATCH or MATCH |
NOMATCH: Unmatched master key code is sent MATCH: Registered master key code is sent |
|
|
SUB KEY |
Sub-key code signal / NO MATCH or MATCH |
NOMATCH: Unmatched sub-key code is sent MATCH: Registered sub-key code is sent |
|
|
BCC |
Transponder chip signal / NG or OK |
NG: Incorrect data sent OK: Correct data sent |
|
|
ENCRYPT CODE |
Transponder chip data / NG or OK |
NG: Data error OK: Data OK |
|
|
SERIAL NUMBER |
Transponder chip data / NG or OK |
NG: Data error OK: Data OK |
|
|
FRAME |
Transponder chip data / NG or OK |
NG: Data error OK: Data OK |
|
|
RESPONSE |
Transponder chip data / NG or OK |
NG: Data error OK: Data OK |
|
|
REG CODE SPACE |
Memory space for key codes registration/ NOT FUL or FULL |
NOT FUL: Possible to register more key codes FULL: Cannot register any more key codes |
|
|
REGIST SUB CODE |
Number of registered sub-key/ min. 0, max. 15 |
Number of registered sub-keys |
|
|
REGIST MAS CODE |
Number of registered master key/ min. 0, max. 15 |
Number of registered master keys |
|
|
G-CODE SUPPORT |
- |
NOT SUP: G-code is not supported SUPPORT: G-code is supported |
2. PERFORM ACTIVE TEST
HINT:
Performing the intelligent tester's ACTIVE TEST allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the ACTIVE TEST early in troubleshooting is one way to save time. The Data List can be displayed during the ACTIVE TEST.
(a) Connect the intelligent tester (with CAN VIM) to the DLC3.
(b) Turn the ignition switch ON.
(c) Perform the ACTIVE TEST by following the directions on the tester screen.
Transponder key ECU assembly:
|
Item |
Test Details |
Diagnostic Note |
|---|---|---|
|
SECURITY INDIC |
Turn security indicator ON/OFF |
- |
|
|