| Last Modified: 7-3-2017 | 6.8:8.0.40 | Doc ID: RM000001B6R004X |
| Model Year Start: 2007 | Model: LX470 | Prod Date Range: [08/2006 - ] |
| Title: WINDSHIELD / WINDOWGLASS: POWER WINDOW CONTROL SYSTEM: DATA LIST / ACTIVE TEST; 2007 MY LX470 [08/2006 - ] | ||
DATA LIST / ACTIVE TEST
1. READ DATA LIST
HINT:
Using the intelligent tester's DATA LIST allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the DATA LIST early in troubleshooting is one way to save time.
(a) Connect the intelligent tester (with CAN VIM) to the DLC3.
(b) Turn the ignition switch ON.
(c) Read the DATA LIST by following the directions on the tester screen.
Power window control system
|
Item |
Measurement Item / Display (Range) |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
P/W AUTO SW |
Driver side power window auto up/down switch / ON or OFF |
ON: Driver side door P/W auto switch is ON position OFF: Driver side door P/W auto switch is OFF position |
- |
|
P P/W AUTO SW |
Front passenger side power window auto up/down switch/ ON or OFF |
ON: Front passenger side door remote P/W auto switch is ON position OFF: Front passenger side door remote P/W auto switch is OFF position |
- |
|
RR P/W AUTO SW |
Rear power window RH auto up/down switch/ ON or OFF |
ON: Rear door RH remote P/W auto switch is ON position OFF: Rear door RH remote P/W auto switch is OFF position |
- |
|
RL P/W AUTO SW |
Rear power window LH auto up/down switch/ ON or OFF |
ON: Rear door LH P/W auto switch is ON position OFF: Rear door LH P/W auto switch is OFF position |
- |
|
LIMIT SW |
Jam protection limit switch / ON or OFF |
ON: Jam protection limit switch is ON position OFF: Jam protection limit switch is OFF position |
- |
|
LOCK POS SW |
Power window lock switch / ON or OFF |
ON: Door unlock detection switch is ON position OFF: Door unlock detection switch is OFF position |
- |
|
GLASS POS-1/4 |
Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open position / OK or CAUTION |
OK Margin is sufficient during manual UP operation: CAUTION: May be displayed even when no resistance is applied in either position. In this case there is a foreign object stuck in that position |
- |
|
GLASS POS-2/4 |
Margin for jam protection triggering force of window glass within range of fully closed to 1/2 open position / OK or CAUTION |
OK: Margin is sufficient during manual UP operation CAUTION: May be displayed even when no resistance is applied in either position. In this case there is a foreign object stuck in that position |
- |
|
GLASS POS-3/4 |
Margin for jam protection triggering force of window glass within range of fully closed to 3/4 open position / OK or CAUTION |
OK Margin is sufficient during manual UP operation: CAUTION: May be displayed even when no resistance is applied in either position. In this case there is a foreign object stuck in that position |
- |
|
GLASS POS-OPEN |
Margin for jam protection triggering force of window glass within range of fully closed to 3/4 to fully open position / OK or CAUTION |
OK: Margin is sufficient during manual UP operation CAUTION: May be displayed even when no resistance is applied in either position. In this case there is a foreign object stuck in that position |
- |
|
UP/DOOR KEY |
Make all door windows go up manually by holding driver's side door key to lock side for 1.5 seconds when ignition switch is OFF / NOT AVL or AVAIL |
NOT AVL: Function is not available AVAIL: Function is available |
- |
|
DOWN/DOOR KEY |
Make all door windows go down manually by holding driver's side door key to lock side for 1.5 seconds when ignition switch is OFF / NOT AVL or AVAIL |
NOT AVL: Function is not available AVAIL: Function is available |
- |
2. PERFORM ACTIVE TEST
HINT:
Perform the intelligent tester's ACTIVE TEST allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the ACTIVE TEST early in troubleshooting is one way to save time. The DATA LIST can be displayed during the ACTIVE TEST.
(a) Connect the intelligent tester (with CAN VIM) to the DLC3.
(b) Turn the ignition switch ON.
(c) Perform the ACTIVE TEST by following the directions on the tester screen.
Power window control system
|
Item |
Test Details |
Diagnostic Note |
|---|---|---|
|
P/W UP/DOWN |
Driver power window UP/DOWN |
- |
|
|