LIGHTING (EXT): LIGHTING SYSTEM: CUSTOMIZE PARAMETERS (2008 LX570)

CUSTOMIZE PARAMETERS

1. CUSTOMIZING FUNCTION WITH TECHSTREAM (REFERENCE)

NOTICE:

When the customer requests a change in a function, first make sure that the function can be customized.
Be sure to make a note of the current settings before customizing.
When troubleshooting a function, first make sure that the function is set to the default setting.

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Enter the following menus: Customize Setting.

(e) Select the setting by referring to the table below.

Illuminated Entry

Display	Default	Content	Setting
I/L when ACC OFF	ON	Function to illuminate the interior light when the engine switch is turned from on (IG) or on (ACC) to off.	ON/OFF
Lighting Time	15s	Function to change the lighting time after closing the door. (It will quickly fade out in the case of turning the engine switch on (IG)).	7.5s/15s/30s
Light Control	ON	Function to illuminate the door inside handle illumination light when the engine switch is on (IG) and the shift lever is not in P.	ON/OFF
I/L ON W/Door Key Unlock	ON	Function to illuminate the interior light, etc. when the door is unlocked with a transmitter, door key or door lock control switch.	ON/OFF
Mirr-Foot-Lgt Approached	ON	Door mirror foot light (when key enters key ID detection area).	ON/OFF
Mirr-Foot-Lgt Unlocked	ON	Door mirror foot light (when doors are unlocked with transmitter).	ON/OFF
Mirr-Foot-Lgt w/Master SW	ON	Door mirror foot light (when doors are unlocked with door lock master switch).	ON/OFF
Mirror Foot Light Time	15s	Door mirror foot light illumination duration.	0s/7.5s/15s/30s
Room Light when Aprchd	ON	Dome light illumination (when key enters key ID detection area).	ON/OFF
Inside Foot Light	ON	Interior foot light illumination.	ON/OFF
Center Console Spot Light	ON	Center console spot light.	ON/OFF

Light Control

Display	Default	Content	Setting
Light Auto OFF Delay	30s	Function to illuminate the headlight for a certain period of time after closing all the doors with the engine switch turned from on (IG) to off under the condition that the headlights illuminate with the light control switch at head or AUTO.	OFF/30s/60s/90s
Sensitivity	NORMAL	Function to adjust the sensitivity of the lighting illumination*1.	Light2/Light1/Normal/Dark1/Dark2
Disp Ex ON Sen	NORMAL	Changes the brightness when dimming the lights such as the combination meter indicator light, A/C indicator light, and clock light. Refer to the illumination*2.	LIGHT2/LIGHT1/NORMAL/DARK1/DARK2
Disp Ex OFF Sen	NORMAL	Adjusts the brightness when lights such as the combination meter, indicator light, A/C indicator light and clock light brighten. Refer to illumination*3.	LIGHT2/LIGHT1/NORMAL/DARK1/DARK2
DRL Function	ON	DRL control.	ON/OFF

HINT:

The sensitivity adjustment may be difficult to confirm. Check by driving the vehicle of the customer.

Illumination*1

Lighting Brightness
Setting	Dark2	Dark1	Normal	Light1	Light2

Illumination*2

Brightness when dimming the lights
Setting	DARK2	DARK1	NORMAL	LIGHT1	LIGHT2

Illumination*3

Brightness when lights brighten
Setting	DARK2	DARK1	NORMAL	LIGHT1	LIGHT2

2. Door linked map light and personal light illumination control

Mode 1: When door is opened, map light of opened door illuminates, or personal light illuminates

Mode 2: When door is opened, all map lights and personal lights illuminate

Mode 3: Map lights and personal lights are not linked to doors

(a) To change modes, press the map light assembly DOOR and on switch simultaneously, and then turn the engine switch from off to on (IG). Each engine switch off to on (IG) operation will change the mode (Mode 1 → Mode 2 → Mode 3 → Mode 1).

HINT:

After changing modes, the map light responds by blinking as follows: Mode 1: once; Mode 2: twice; Mode 3: three times.