Home General Introduction REPAIR INSTRUCTION
Last Modified: 11-27-2007 1.6 D
Service Category: General Section: Introduction
Model Year: 2008 Model: LX570 Doc ID: RM000000UZ003DX
Title: INTRODUCTION: REPAIR INSTRUCTION: CUSTOMIZE PARAMETERS (2008 LX570)

CUSTOMIZE PARAMETERS

HINT:

The following items can be customized.

NOTICE:

  • When the customer requests a change in a function, first make sure that the function can be customized.
  • Be sure to make a note of the current settings before customizing.
  • When troubleshooting a function, first make sure that the function is set to the default setting.

1. CUSTOMIZING FUNCTION WITH TECHSTREAM

(a) POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

Tilt & Telesco

Display

Default

Contents

Setting

Autoaway/Return function

ON

Turn the auto away/return function ON/OFF

ON/OFF

(b) INTUITIVE PARKING ASSIST SYSTEM

Warning

Display

Default

Contents

Setting

Rr Sensor Onset Range

Wide

Sets the buzzer activation range for the rear sensors.

Narrow or Wide

Keep Sense Buzzer

Avail

Makes the buzzer sound when the distance between the vehicle and obstacle does not change for more than 3 seconds.

Not Avail or Avail

Fr & Rr Buzzer Volume

H

Changes the buzzer volume setting.

L, M1, M2, M3 or H

Sensor

Display

Default

Contents

Setting

Sensor Condition N

Avail

Makes the sensors available when the shift lever is in N.

Not Avail or Avail

Reverse Range Front Sensor

F

Changes the operation setting for the vehicle front sensors when the shift lever is in R.

F or F Stop

Non P/R Range Rear Sensor

R Stop

Changes the operation setting for the vehicle rear sensors when the shift lever is not in P or R.

R, Rcrn or R Stop

Display

Display

Default

Contents

Setting

Approach Display OFF

Avail

The display when moving away from a previously detected obstacle.

Not Avail or Avail

Display Mode

All

The display mode setting (when the intuitive parking assist system is normal).

All or Undisp

(c) POWER DOOR LOCK CONTROL SYSTEM

Door Lock

Display

Default

Contents

Setting

Unlock Key Twice

ON

Function that unlocks only the driver side door when the driver side door key cylinder is turned to unlock once, and unlock all doors when it is turned to unlock twice. For the OFF setting, turning it once unlocks all doors.

ON/OFF

Auto Lock

OFF

Function that locks all doors when the vehicle speed reaches a certain level.

ON/OFF

Auto Lock/Shift

ON

Function that locks all doors when the shift lever is moved from P to any position other than P while the engine running and all doors are closed.

ON/OFF

Auto Unlock/Shift

ON

Function that unlocks all doors when the shift lever is moved to P from any position other than P while the engine switch is on (IG).

ON/OFF

All Unlock/Open-Close

OFF

Function that unlocks the other doors when the driver side door is opened within 10 seconds after the engine switch is turned off.

ON/OFF

(d) WIRELESS DOOR LOCK CONTROL SYSTEM

Wireless Door Lock

Display

Default

Contents

Setting

Hazard Answer Back

ON

When the lock switch on the transmitter is pressed, this function illuminates the hazard warning lights once. When the unlock switch is pressed, the hazard warning lights illuminate twice.

ON/OFF

Wireless Control

ON

Function that turns the wireless door lock function on or off.

ON/OFF

Open Door Warning

ON

If a door is not completely closed and the transmitter lock switch is pressed, this function makes the buzzer sound for 10 seconds.

ON/OFF

Panic Alarm Function

ON

Function to operate the theft deterrent system by continuously pressing the panic switch on transmitter for 1 second or more.

ON/OFF

Unlock 2 Operation

ON

Function that unlocks the driver side door when the unlock switch on the transmitter is pressed once, and unlocks all doors when the switch is pressed twice. If the setting is OFF, pressing the unlock switch once makes all the doors unlock.

ON / OFF

Auto Lock Time

60 s

Function to change the time until relocking after unlocking with the wireless door lock function.

30 s/60 s/120 s

Wireless Auto Lock

ON

Function to control the automatic relocking of doors after unlocking with the wireless door lock function.

ON/OFF

Wireless Buzzer Volume

Level 7

This function changes the wireless buzzer volume.

Level 0/Level 1/Level 2/Level 3/Level 4/Level 5/Level 6/Level 7

PSD&PBD Operation (w/ Power Back Door System)

Display

Default

Contents

Setting

PBD One Motion

ON

Function to turn on/off the power back door wireless one motion open operation.

ON/OFF

Wireless PBD SW Operation

0.8s

Function to change the way the power back door is operated by the back door switch.

1time/2times/0.8s/OFF

(e) SMART ACCESS WITH PUSH-BUTTON START (for Entry Function)

Smart Key / Access

Display

Default

Contents

Setting

Park Wait Time*1

2.5s

Function that sets the waiting time to permit unlocking the door after the door is locked with the entry lock function.

0.5s/1.5s/2.5s/5s

Ignition Area*2

ALL

Function to choose the available area for the key to start the engine and cancel the steering lock.

FRONT/ALL*3

Back Door Opening Operation*4

LONG

The back door opening operation.

LONG/TWICE/OFF

Warning

Display

Default

Contents

Setting

Key Low Battery Warning*5

ON

Function that warns the driver that the key battery power is low.

ON/OFF

HINT:

*1: Waiting time to permit unlocking door after locking.

*2: Entry ignition available area.

*3: "FRONT" means front, and "ALL" means front floor, rear floor and luggage compartment.

*4: Back door open mode when vehicle is locked.

*5: Warn when key battery becomes weak.

(f) ENTRY UNLOCK MODE SWITCHING FUNCTION

(1) To use the entry unlock mode switching function, make sure the engine switch is off and simultaneously press and hold the lock switch on the key and another key switch for 5 seconds.

When the switches are pressed and held for 5 seconds, the entry door unlock mode changes in the following order: driver door unlock mode, all door unlock mode.

NOTICE:

After pressing and holding the switches for 5 seconds, wait 5 seconds before performing the same procedure again.

  • Driver door unlock mode (default):

    When the driver door touch sensor is touched, only the driver door unlocks. When another touch sensor is touched, all doors unlock.

  • All door unlock mode:

    When a touch sensor is touched, all doors unlock.

(2) The certification ECU (smart key ECU assembly) receives this signal from the door control receiver and changes the smart access system with push-button start to the entry unlock mode.


(3) The certification ECU (smart key ECU assembly) sounds the wireless door lock buzzer and combination meter buzzer to inform the user that the mode has been switched.

HINT:

The function only changes the entry unlock mode of the smart access system with push-button start. It does not switch the unlocking of the wireless door lock control.

  • Driver door unlock mode:
  • All door unlock mode:

(g) SMART ACCESS WITH PUSH-BUTTON START (for Start Function)

Smart Key / Access

Display

Default

Content

Setting

Ignition Available Area

All

Function to choose the available area for the key to start the engine and cancel the steering lock.

Front/All

(h) THEFT DETERRENT SYSTEM

Security

Display

Default

Contents

Setting

Passive Mode

(Security System)

OFF

Passive arming mode is a function that switches theft deterrent system from arming preparation state to armed state 30 seconds after key is not inside vehicle and driver side door is closed.

In passive arming mode, theft deterrent system will judge that a theft is taking place and switch to alarm sounding state if one of the following operations are not performed within 14 seconds (see entry delay below) after door is opened:

  • Unlock any door by key or wireless operation
  • Turn engine switch on (IG)

ON/OFF

Warning by Horn

ON

Function that allows vehicle horns and security horn to be used as warning device.

ON/OFF

Entry Delay Time

14 s

Function that changes entry delay time (time before warning starts) for PASSIVE ARMING MODE.

0 s/14 s/30 s

(i) METER AND GAUGE SYSTEM

Warning

Display

Default

Contents

Setting

Driver Side Seatbelt Warning Buzzer

ON

To change the seat belt warning buzzer.

ON / OFF

Front Passenger Side Seatbelt Warning Buzzer

ON

To change the seat belt warning buzzer.

ON / OFF

Unit Conversion

Display

Default

Contents

Setting

Units By Region

Different for each vehicle

To change the units of the display.

Km/l JP / Km/l / Ml/g US / Ml/g UK

Display

Display

Default

Contents

Setting

Language

None

To change the language of the display.

Eng US / Eng UK / French / German / Spanish / Italian / Japanes / CHN Sim / CHN Trd

(j) SEAT BELT WARNING SYSTEM

Seat Belt Warning

Display

Default

Contents

Setting

Driver Side Seatbelt Warning Buzzer

ON

If the driver side seat belt is unfastened and the vehicle is driven at approximately 20 km/h (12.5 mph) or more, this system sounds the seat belt warning buzzer.

ON/OFF

Front Passenger Side Seatbelt Warning Buzzer

ON

If the front passenger side seat belt is unfastened and the vehicle is driven at approximately 20 km/h (12.5 mph) or more, this system sounds the seat belt warning buzzer.

ON/OFF

(k) AIR CONDITIONING SYSTEM

Air Conditioner

Display

Default

Contents

Setting

Set Temperature Shift

Normal

Function to set the temperature shift.

+2 C/+1 C/Normal/-1 C/-2 C

Evaporator Control

Automatic

Function to set the evaporator control to the automatic position (Automatic) to save power, or to the coldest position (Manual) to dehumidify the air and to prevent the windows from fogging up.

Manual/Automatic

Compressor/Air Inlet DEF operation

Link

Function to automatically turn the A/C on when the front defroster button is pressed.

Normal/Link

Compressor Mode

Automatic

Function to turn the A/C on automatically by pressing the AUTO button when the blower is on and the A/C is off.

Manual/Automatic

Air Inlet Mode

Automatic

Function to automatically change to recirculation mode when the A/C is turned on.

Manual/Automatic

Foot/DEF Auto Mode

ON

Function to turn on the airflow from the front and rear footwell register ducts and center and side defrosters automatically when auto mode is on.

ON/OFF

Foot/DEF Automatic Blow Up Function

ON

Function to change the blower level automatically when the defroster is on.

ON/OFF

Ambient Temperature Shift

Normal

Function to control the shifted ambient temperature in relation to the displayed ambient temperature.

+3 C/+2 C/+1 C/Normal/-1 C/-2 C/-3 C

Button Press Buzzer

ON

Function to sound a buzzer when a button is pressed.

ON/OFF

Emission Gas Sensor Shift

Normal

Function to change the sensitivity of the exhaust gas sensor.

Much More/More/Little More/Normal/Little Less/Less/Much Less

(l) POWER WINDOW CONTROL SYSTEM

Power Window

Display

Default

Contents

Setting

Door Key P/W Up

ON

Function that raises all the power windows when, with the engine switch off, a key is used to hold the driver door key cylinder to the lock position for more than 2.3 sec.

ON/OFF

Door Key P/W Down

ON

Function that lowers all the power windows when, with the engine switch off, a key is used to hold driver door key cylinder to the unlock position for more than 2.3 sec.

ON/OFF

P/W Down W/ Transmit

ON

Function that lowers all the power windows when, with the engine switch off, the unlock switch on the transmitter is pressed and held for more than 3.0 sec.

ON/OFF

P/W Up W/ Smart

ON

Function that raises all the power windows when, with the engine switch off, the entry lock switch on the driver side door outside handle is pressed and held for more than 3.0 sec.

ON/OFF

(m) SLIDING ROOF SYSTEM

Slide Roof

Display

Default

Contents

Setting

Door Key Related Open

ON

The function to manually open the sliding roof linked with the power window if holding the driver side door key for 3 seconds or more to unlock position when the engine switch is off.

ON/OFF

Door Key Related Close

ON

The function to manually close the sliding roof linked with the power window if holding the driver side door key for 3 seconds or more to lock position when the engine switch is off.

ON/OFF

Wireless Key Related Open

ON

The function to manually open the sliding roof linked with the power window if pressing the transmitter unlock switch for 3 seconds or more when the engine switch is off.

ON/OFF

Door Handle Lock Button

ON

The function to manually close the sliding roof linked with the power window if pushing the door lock switch for 3 seconds or more when the engine switch is off and the key is outside vehicle.

ON/OFF

Door Key Related Operation

Slide

The function to select tilt up or slide open of manual sliding roof operation linked with the power window activated by holding the driver side door key for 3 seconds or more to unlock position when the engine switch is off.

Tilt/Slide

Wireless Key Related Operation

Slide

The function to select tilt up or slide open of manual sliding roof operation linked with the power window activated by pressing on the transmitter unlock switch for 3 seconds or more when the engine switch is off.

Tilt/Slide

(n) POWER BACK DOOR SYSTEM

PSD & PBD Operation

Display

Default

Contents

Setting

PBD Power Operation

Valid

Makes power back door function ON or OFF

Valid/Invalid

PBD SW Operation

0.8 s

A function that turns the power back door closer switch on when the switch is pushed once or is held down for 0.8 sec.

0.8s/ON

PBD Buzzer

ON

A function that makes the power back door buzzer sound when the power back door is operating.

ON/OFF

Wireless PBD Operation

0.8 s

A function that operates the power back door when the transmitter switch is pressed in a specified way (1 time, 2 times, 0.8 sec. press, or off).

1 time/2 times/0.8 s/OFF

(o) LIGHTING SYSTEM

Illuminated Entry

Display

Default

Contents

Setting

I/L when ACC OFF

ON

Function to light the interior light when the engine switch is turned from on (IG) or on (ACC) to off.

ON/OFF

Lighting Time

15s

Function to change the lighting time after closing the door.

(It will quickly fade out in the case of turning the engine switch on (IG)).

7.5s/15s/30s

Light Control

ON

Function to light up the door inside handle light when the engine switch is on (IG) and the shift lever is not in P.

ON/OFF

I/L ON W/Door Key Unlock

ON

Function to light the interior light, etc. when the door is unlocked with a transmitter, door key or door lock control switch.

ON/OFF

Mirr-Foot-Lgt Approached

ON

Door mirror foot light (when approaching the vehicle).

ON/OFF

Mirr-Foot-Lgt Unlocked

ON

Door mirror foot light (when unlocking the doors).

ON/OFF

Mirr-Foot-Lgt w/Master SW

ON

Door mirror foot light (when manually unlocking the doors).

ON/OFF

Mirror Foot Light Time

15s

Door mirror foot light illumination duration.

0s/7.5s/15s/30s

Room Light when Aprchd

ON

Dome light illumination (when approaching the vehicle).

ON/OFF

Inside Foot Light

ON

Interior foot light illumination.

ON/OFF

Center Console Spot Light

ON

Center console spot light.

ON/OFF

Light Control

Display

Default

Contents

Setting

Light Auto OFF Delay

30s

Function to keep on lighting the headlight for a certain period of time after closing all the doors with the engine switch turned from on (IG) to off under the condition that the light control switch is at head or AUTO with the headlight ON.

OFF/30s/60s/90s

Sensitivity

NORMAL

Function to adjust the sensitivity of the lighting illumination*1.

Light2/Light1/Normal/Dark1/Dark2

Disp Ex ON Sen

NORMAL

Changes the brightness when lowering the lights such as the combination meter indicator light, A/C indicator light, and clock light. Refer to the illumination*2.

LIGHT2/LIGHT1/NORMAL/DARK1/DARK2

Disp Ex OFF Sen

NORMAL

Changes the brightness when canceling the lowering of the lights such as the combination meter indicator light, A/C indicator light, and clock light. Refer to the illumination*3.

LIGHT2/LIGHT1/NORMAL/DARK1/DARK2

DRL Function

ON

DRL control.

ON/OFF

HINT:

The sensitivity adjustment may be difficult to confirm. Check by driving the vehicle of the customer.

Illumination*1

Lighting Brightness



Setting

Dark2

Dark1

Normal

Light1

Light2

Illumination*2

Brightness of lowering the lights



Setting

DARK2

DARK1

NORMAL

LIGHT1

LIGHT2

Illumination*3

Brightness when canceling the lowering of the lights



Setting

DARK2

DARK1

NORMAL

LIGHT1

LIGHT2