- Unit: °C (°F).
- If the value is -40 (-40): The sensor circuit is open.
- If the value is 140 (284): The sensor circuit is shorted.
| Last Modified: 11-27-2007 | 1.6 U | |
| Service Category: Vehicle Interior | Section: Meter/Gauge/Display | |
| Model Year: 2008 | Model: LX570 | Doc ID: RM000002Z4S004X |
| Title: METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM: DATA LIST / ACTIVE TEST (2008 LX570) | ||
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical, Powertrain or Chassis / (desired system) / Data List.
(e) According to the display on the Techstream, read the Data List.
Combination Meter
|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
ODO/TRIP Change SW |
ODO/TRIP switch condition/ON or OFF |
ON: ODO/TRIP switch pushed OFF: ODO/TRIP switch not pushed |
- |
|
Tail Cancel SW |
TAIL cancel switch condition/ON or OFF |
ON: TAIL cancel switch on OFF: TAIL cancel switch off |
- |
|
Washer Switch |
Washer switch/ON or OFF |
ON: Washer switch on OFF: Washer switch off |
- |
|
P-Seatbelt Buckle SW |
Front passenger side seat belt warning light request signal/ON or OFF |
ON: Tongue plate (for front passenger side) inserted OFF: Tongue plate (for front passenger side) not inserted |
- |
|
Oil Level SW |
Oil level switch/ON or OFF |
ON: Oil level switch on OFF: Oil level switch off |
- |
|
Multi Display Select Switch |
Steering multi-display select switch/ON or OFF |
ON: Steering multi-display select switch on OFF: Steering multi-display select switch off |
- |
|
Vehicle Speed Meter |
Vehicle speed/Min.: 0 (0), Max.: 255 (158) |
Almost same as actual vehicle speed (when driving) |
Unit: km/h (mph) |
|
Engine Rpm |
Engine speed/Min.: 0, Max.: 12750 |
Idling: 700 to 800 |
Unit: rpm |
|
Coolant Temperature |
Engine coolant temperature/Min.: -40 (-40), Max.: 140 (284) |
After warming up: 80 to 105 (176 to 221) |
|
|
Integrated value for Oil Maintenance |
Oil maintenance warning integrated value/Min.: 0 (0), Max.: 25500 (41037) |
0 (0) to 25500 (41037) |
Unit: mile (km) |
|
Fuel Input |
Fuel sender gauge input/Min.: 0, Max.: 127.5 |
Fuel sender input value |
Unit: L |
|
Rheostat value |
Light control rheostat switch input/Min.: 0, Max.: 100 |
Light control rheostat switch is fully turned left (0) → fully turned right (100) |
Unit: % |
|
Quantity of Outside Light |
Outside dimmer output/Min.: 0, Max.: 100 |
0 to 100 |
Unit: % |
|
Communication ECM/Meter DTC 3 |
ECM communication stop history/Rec or Unrec |
Rec: DTC stored Unrec: DTC not stored |
- |
|
ECM ODO (History 3) |
ECM odometer history/Min.: 0, Max.: 999999 |
With history: 0 to 999999 Without history: ffffffh |
- |
|
Communication ECM/Meter DTC 2 |
ECM communication stop history/Rec or Unrec |
Rec: DTC stored Unrec: DTC not stored |
- |
|
ECM ODO (History 2) |
ECM odometer history/Min.: 0, Max.: 999999 |
With history: 0 to 999999 Without history: ffffffh |
- |
|
Communication ECM/Meter DTC 1 |
ECM communication stop history/Rec or Unrec |
Rec: DTC stored Unrec: DTC not stored |
- |
|
ECM ODO (History 1) |
ECM odometer history/Min.: 0, Max.: 999999 |
With history: 0 to 999999 Without history: ffffffh |
- |
|
Communication ABS/Meter DTC 3 |
Skid control ECU communication stop history/Rec or Unrec |
Rec: DTC stored Unrec: DTC not stored |
- |
|
ABS/VSC ODO (History 3) |
Skid control ECU odometer history/Min.: 0, Max.: 999999 |
With history: 0 to 999999 Without history: ffffffh |
- |
|
Communication ABS/Meter DTC 2 |
Skid control ECU communication stop history/Rec or Unrec |
Rec: DTC stored Unrec: DTC not stored |
- |
|
ABS/VSC ODO (History 2) |
Skid control ECU odometer history/Min.: 0, Max.: 999999 |
With history: 0 to 999999 Without history: ffffffh |
- |
|
Communication ABS/Meter DTC 1 |
Skid control ECU communication stop history/Rec or Unrec |
Rec: DTC stored Unrec: DTC not stored |
- |
|
ABS/VSC ODO (History 1) |
Skid control ECU odometer history/Min.: 0, Max.: 999999 |
With history: 0 to 999999 Without history: ffffffh |
- |
|
Units By Region |
Units of display setting / Km/l JP, Km/l, Ml/g US or Ml/g UK |
Displays units setting |
- |
|
Language |
Language of display setting/English, Spanish, French, German or Italian |
Displays language setting |
- |
|
Driver Side Seatbelt Warning Buzzer |
Front driver side seat belt warning buzzer setting/ON or OFF |
ON: Front driver side seat belt warning buzzer ON setting OFF: Front driver side seat belt warning buzzer OFF setting |
- |
|
P-Seatbelt Warning Buzzer |
Front passenger side seat belt warning buzzer setting/ON or OFF |
ON: Front passenger side seat belt warning buzzer ON setting OFF: Front passenger side seat belt warning buzzer OFF setting |
- |
|
+B Voltage Value |
+B voltage/Min.: 0, Max.: 25.5 |
Below 1 to 14 |
Unit: V |
Engine
|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
Engine Rpm |
Engine speed/Min.: 0, Max.: 16383.75 |
Idling: 700 to 800 |
Unit: rpm |
|
Vehicle Speed Meter |
Vehicle speed/Min.: 0 (0), Max.: 255 (158) |
Actual vehicle speed |
|
|
Coolant Temp |
Engine coolant temperature/Min.: -40 (-40), Max.: 140 (284) |
After warming up: 80 to 100 (176 to 221°F) |
If the value is -40 (-40°F): The sensor circuit is open. If the value is 140 (284°F): The sensor circuit is shorted. |
2. ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / (Combination Meter) / Active Test.
(e) According to the display on the Techstream, perform the Active Test.
Combination Meter
|
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Speed Meter Operation*1 |
Speedometer |
0, 40, 80, 120, 160, 200, 240 or 280 |
Perform the test with the vehicle stopped and the engine idling. |
|
Tachometer operation |
Tachometer |
0, 1000, 2000, 3000, 4000, 5000, 6000 or 7000 |
Perform the test with the vehicle stopped and the engine idling. |
|
Fuel Meter Operation |
Fuel receiver gauge |
EMPTY, 1/2 or FULL |
Perform the test with the vehicle stopped and the engine idling. |
|
Volt Meter Operation |
Voltmeter |
0, 3, 6, 9, 12, 15 or 18 |
Perform the test with the vehicle stopped and the engine idling. |
|
Oil Pressure Meter Operation |
Oil pressure receiver gauge |
LOW, 1/4, 1/2, 3/4 or HIGH |
Perform the test with the vehicle stopped and the engine idling. |
|
A/T Indicator operation 1 |
A/T indicator (normal mode) |
P, R, N, D, 4, 3, 2 or L |
Perform the test with the vehicle stopped and the engine idling. |
|
A/T Indicator operation 2 |
A/T indicator (sequential mode) |
Es, 5 or 6 |
Perform the test with the vehicle stopped and the engine idling. |
|
Meter Display 1*2 |
All dots in the multi-information display |
ALL, 0, 1, 2, 3, 4, 5 or 6 |
Perform the test with the vehicle stopped and the engine idling. |
|
Meter Display 2*2 |
All dots in the multi-information display |
7, 8 or 9 |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. Lamp Beam |
BEAM indicator light |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. Lamp Head*3 |
HEAD indicator light |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. Lamp Tail*4 |
TAIL indicator light |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. Lamp Fr FOG |
Fr. FOG indicator light |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. Lamp Airbag |
SRS warning light |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. Precrash*5 |
PCS indicator light |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat AFS |
AFS OFF indicator light |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Driver Side Seat Belt |
Driver side seat belt warning light |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Front Passenger Side Seat Belt |
Passenger side seat belt warning light |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. Lamp Doors All Open |
All doors open light |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. Lamp Washer |
Multi-information display |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. Lamp Fuel |
Low fuel warning light |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. Lamp Charge |
CHARGE warning light |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. Lamp ABS |
ABS warning light |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. Lamp Slip |
SLIP indicator light |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. Tire Pressure Warning System |
TIRE PRESSURE indicator light |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. Lamp Brake |
Brake warning light |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. Lamp oil Level |
Multi-information display |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. Lamp ECT PWR |
ECT PWR indicator light |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. Lamp Cruise |
CRUISE main indicator light |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. KEY |
Multi-information display |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Master Warning |
Master warning light |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. INTUITIVE P/A LCD |
Multi-information display |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. VSC OFF |
Multi-information display |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. 2nd START |
2nd START indicator light |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. Ctr DIFF LOCK |
Center differential lock indicator light |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. 4LO |
4LO indicator light |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. Ride Mode |
ACCESS MODE indicator light |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. CRAWL |
CRAWL indicator light |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Indicat. A/T P |
AT/ P warning light |
ON or OFF |
Perform the test with the vehicle stopped and the engine idling. |
|
Water Temperature Meter Operation |
Engine coolant temperature receiver gauge |
LOW, NORMAL or HIGH |
Perform the test with the vehicle stopped and the engine idling. |
*1:
- The doors will be locked automatically when performing the speedometer Active Test. This is a normal function.
- The displayed value has the same units (km/h, mph) as the main scale of the vehicle speedometer.
- The needle position should be within the acceptable range.
*2: If this Active Test is being performed and the engine switch is turned off and then on (IG), the A/T and ODO/TRIP display background may turn white. If this occurs, end this Active Test and turn the engine switch off.
*3: for U.S.A.
*4: except U.S.A.
*5: w/ Pre-Collision System
Main Body
|
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Dimmer Signal |
Illumination dimming operation |
ON or OFF |
- |
|
|