REAR DRIVE SHAFT > INSTALLATION

for Preparation Click here

1. Align the matchmarks.
   

2. Install the rear drive shaft assembly with the 4 nuts and washers.
   

   Torque:

   56 N*m{ 571 kgf*cm , 41 ft.*lbf }

1. Install the rear axle carrier sub-assembly with the 2 bolts and nuts to the shock absorber.
   

   Torque:

   180 N*m{ 1,840 kgf*cm , 133 ft.*lbf }

   NOTICE:

   1. Be careful not to damage the outboard joint boot.
      
   2. Be careful not to damage the speed sensor rotor.
      
   3. Prevent foreign matter from adhering to the speed sensor rotor.
      

   HINT:

   Insert the bolt from the rear side of the vehicle and tighten the bolt.

1. Temporarily tighten the rear suspension arm assembly No.2 with the bolt and nut.
   

   HINT:

   Insert the bolt from the rear side of the vehicle and lightly tighten the bolt.

1. Temporarily tighten the rear suspension arm assembly No.1 with the bolt and nut.
   

   HINT:

   Insert the bolt from the front side of the vehicle and lightly tighten the bolt.

1. Temporarily tighten the strut rod assembly rear with the bolt and nut.
   

   HINT:

   Insert the bolt from the inside of the vehicle and lightly tighten the bolt.

2. Temporarily tighten the strut rod assembly rear with the bolt and nut.
   

   HINT:

   Insert the bolt from the inside of the vehicle and lightly tighten the bolt.

1. Install the hub and bearing assembly with the 4 bolts.
   

   Torque:

   75 N*m{ 765 kgf*cm , 55 ft.*lbf }

1. Aligning the matchmarks, install the rear disc.
   

   HINT:

   When replacing the rear disc with a new one, select the installation position where the rear disc has the minimum runout.

1. Install the rear disc brake caliper assembly with the 2 bolts to the rear axle carrier.
   

   Torque:

   78 N*m{ 795 kgf*cm , 58 ft.*lbf }

1. Install the speed sensor with the bolt.
   

   Torque:

   8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

   NOTICE:

   1. Be careful not to damage the speed sensor.
      
   2. Prevent foreign matter from adhering to the speed sensor.
      
   3. Do not twist the sensor wire when installing the sensor.
      

1. Using a socket wrench (30mm), install a new rear axle shaft nut.
   

   Torque:

   294 N*m{ 3,000 kgf*cm , 217 ft.*lbf }

2. Using a chisel and hammer, stake the rear axle shaft nut.
   

1. Jack up the rear axle carrier, placing a wooden block to avoid damage. Apply load to the suspension so that the rear drive shaft assembly is horizontally positioned.
   

1. Fully tighten the rear suspension arm assembly No.2 with the bolt and nut.
   

   Torque:

   112 N*m{ 1,140 kgf*cm , 83 ft.*lbf }

   HINT:

   While holding the nut, turn the bolt.

1. Fully tighten the rear suspension arm assembly No.1 with the bolt and nut.
   

   Torque:

   112 N*m{ 1,140 kgf*cm , 83 ft.*lbf }

   HINT:

   While holding the nut, turn the bolt.

1. Fully tighten the rear strut rod assembly (rear axle carrier side) with the bolt and nut.
   

   Torque:

   80 N*m{ 816 kgf*cm , 59 ft.*lbf }

   HINT:

   While holding the nut, turn the bolt.

2. Fully tighten the rear strut rod assembly (vehicle side) with the bolt and nut.
   

   Torque:

   80 N*m{ 816 kgf*cm , 59 ft.*lbf }

   HINT:

   While holding the nut, turn the bolt.

1. Install the parking brake cable assembly No.3 with the nut.
   

   Torque:

   6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

Torque:

103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }