CAN COMMUNICATION SYSTEM (for RHD) > Short to B+ in CAN Bus Line

for Preparation Click here


DESCRIPTION

There may be a short circuit between the CAN bus line and +B when the resistance between terminals 6 (CANH) and 16 (BAT), or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 1 MΩ.

Symptom
Suspected Area
Resistance between terminals 6 (CANH) and 16 (BAT), or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 1 MΩ.
  1. Short to +B in CAN bus lines
  2. Skid control ECU
  3. Steering sensor
  4. Yaw rate sensor
  5. Gateway ECU
  6. Television camera ECU
  7. Power steering ECU
  8. HV control ECU

WIRING DIAGRAM


C115376E01


INSPECTION PROCEDURE

1.CHECK CAN BUS LINES FOR SHORT TO +B (DLC3 SUB BUS LINE)


    G031932E77

  1. Disconnect the DLC3 sub bus line connector (J27) from the CAN RH J/C B side (w/o earth terminal).

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    G026206E36

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Value
    D1-6 (CANH) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher
    D1-14 (CANL) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher



NG
REPAIR OR REPLACE DLC3 SUB BUS LINE OR CONNECTOR
OK


2.CONNECT CONNECTOR

  1. Reconnect the DLC3 sub bus line connector (J27) to the CAN RH J/C B side (w/o earth terminal).


NEXT


3.CHECK CAN BUS LINES FOR SHORT TO +B (CAN BUSES TO CAN RH J/C)


    G031932E71

  1. Disconnect the CAN main bus line connector (J25) from the CAN RH J/C B side (w/o earth terminal).

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    G026206E36

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Value
    D1-6 (CANH) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher
    D1-14 (CANL) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher



OK
Go to step 14
NG


4.CONNECT CONNECTOR

  1. Reconnect the CAN main bus line connector (J25) to the CAN RH J/C B side (w/o earth terminal).


NEXT


5.CHECK CAN BUS LINES FOR SHORT TO +B (POWER STEERING ECU SUB BUS LINE)


    G031934E42

  1. Disconnect the power steering ECU sub bus line connector (J50) from the CAN center J/C A side (w/ earth terminal).

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    G026206E36

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Value
    D1-6 (CANH) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher
    D1-14 (CANL) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher



OK
Go to step 10
NG


6.CONNECT CONNECTOR

  1. Reconnect the power steering ECU sub bus line connector (J50) to the CAN center J/C A side (w/ earth terminal).


NEXT


7.CHECK CAN BUS LINES FOR SHORT TO +B (GATEWAY ECU SUB BUS LINE)


    G031934E52

  1. Disconnect the gateway ECU sub bus line connector (J52) from the CAN center J/C A side (w/ earth terminal).

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    G026206E36

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Value
    D1-6 (CANH) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher
    D1-14 (CANL) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher



OK
Go to step 12
NG


8.CONNECT CONNECTOR

  1. Reconnect the gateway ECU sub bus line connector (J52) to the CAN center J/C A side (w/ earth terminal).


NEXT


9.CHECK CAN BUS LINES FOR SHORT TO +B (HV CONTROL ECU MAIN BUS LINE)

  1. Disconnect the HV control ECU connector (H30).



    G026206E36

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Value
    D1-6 (CANH) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher
    D1-14 (CANL) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher



OK
REPLACE HV CONTORL ECU
NG

REPLACE HV CONTROL ECU SUB BUS LINE OR CONNECTOR (CAN-H, CAN-L) 

10.CONNECT CONNECTOR

  1. Reconnect the power steering ECU sub bus line connector (J50) to the CAN center J/C A side (w/ earth terminal).


NEXT


11.CHECK CAN BUS LINES FOR SHORT TO +B (POWER STEERING ECU SUB BUS LINE)

  1. Disconnect the power steering ECU connector (P43).



    G026206E36

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Value
    D1-6 (CANH) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher
    D1-14 (CANL) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher



OK
REPLACE POWER STEERING ECU
NG

REPLACE POWER STEERING ECU SUB BUS LINE OR CONNECTOR (CAN-H, CAN-L) 

12.CONNECT CONNECTOR

  1. Reconnect the gateway ECU sub bus line connector (J52) to the CAN center J/C A side (w/ earth terminal).


NEXT


13.CHECK CAN BUS LINES FOR SHORT TO +B (GATEWAY ECU SUB BUS LINE)

  1. Disconnect the gateway ECU connector (G1).



    G026206E36

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Value
    D1-6 (CANH) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher
    D1-14 (CANL) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher



OK
REPLACE STEERING SENSOR
NG

REPLACE GATEWAY ECU SUB BUS LINE OR CONNECTOR (CAN-H, CAN-L) 

14.CONNECT CONNECTOR

  1. Reconnect the CAN main bus line connector (J25) to the CAN RH J/C B side (w/o earth terminal).


NEXT


15.CHECK CAN BUS LINES FOR SHORT TO +B (SKID CONTROL ECU SUB BUS LINE)


    G031934E53

  1. Disconnect the skid control ECU sub bus line connector (J24) from the CAN RH J/C A side (w/ earth terminal).

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    G026206E36

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Value
    D1-6 (CANH) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher
    D1-14 (CANL) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher



OK
Go to step 22
NG


16.CONNECT CONNECTOR

  1. Reconnect the skid control ECU sub bus line connector (J24) to the CAN RH J/C A side (w/ earth terminal).


NEXT


17.CHECK CAN BUS LINES FOR SHORT TO +B (YAW RATE SENSOR SUB BUS LINE)


    G031932E58

  1. Disconnect the yaw rate sensor sub bus line connector (J26) from the CAN RH J/C B side (w/o earth terminal).

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    G026206E36

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Value
    D1-6 (CANH) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher
    D1-14 (CANL) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher



OK
Go to step 24
NG


18.CONNECT CONNECTOR

  1. Reconnect the yaw rate sensor sub bus line connector (J26) to the CAN RH J/C B side (w/o earth terminal).


NEXT


19.CHECK CAN BUS LINES FOR SHORT TO +B (TELEVISION CAMERA ECU SUB BUS LINE)


    G031932E57

  1. Disconnect the television camera ECU sub bus line connector (J58) from the CAN RH J/C B side (w/o earth terminal).

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    G026206E36

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Value
    D1-6 (CANH) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher
    D1-14 (CANL) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher



OK
Go to step 26
NG


20.CONNECT CONNECTOR

  1. Reconnect the television camera ECU sub bus line connector (J58) to the CAN RH J/C B side (w/o earth terminal).


NEXT


21.CHECK CAN BUS LINES FOR SHORT TO +B (STEERING SENSOR MAIN BUS LINE)

  1. Disconnect the steering sensor connector (S10).



    G026206E36

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Value
    D1-6 (CANH) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher
    D1-14 (CANL) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher



OK
REPLACE STEERING SENSOR
NG

REPLACE STEERING SENSOR MAIN BUS LINE OR CONNECTOR (CAN-H, CAN-L) 

22.CONNECT CONNECTOR

  1. Reconnect the skid control ECU sub bus line connector (J24) to the CAN RH J/C A side (w/ earth terminal).


NEXT


23.CHECK CAN BUS LINES FOR SHORT TO +B (SKID CONTROL ECU SUB BUS LINE)

  1. Disconnect the skid control ECU connector (S40).



    G026206E36

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Value
    D1-6 (CANH) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher
    D1-14 (CANL) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher



OK
REPLACE SKID CONTROL ECU
NG

REPLACE SKID CONTROL ECU SUB BUS LINE OR CONNECTOR (CAN-H, CAN-L) 

24.CONNECT CONNECTOR

  1. Reconnect the yaw rate sensor sub bus line connector (J26) to the CAN RH J/C B side (w/o earth terminal).


NEXT


25.CHECK CAN BUS LINES FOR SHORT TO +B (YAW RATE SENSOR SUB BUS LINE)

  1. Disconnect the yaw rate sensor ECU connector (Y1).



    G026206E36

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Value
    D1-6 (CANH) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher
    D1-14 (CANL) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher



OK
REPLACE YAW RATE SENSOR
NG

REPLACE YAW RATE SENSOR SUB BUS LINE CONNECTOR (CAN-H, CAN-L) 

26.CONNECT CONNECTOR

  1. Reconnect the television camera ECU sub bus line connector (J58) to the CAN RH J/C B side (w/o earth terminal).


NEXT


27.CHECK CAN BUS LINES FOR SHORT TO +B (TELEVISION CAMERA ECU SUB BUS LINE)

  1. Disconnect the television camera ECU connector (T17).



    G026206E36

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Value
    D1-6 (CANH) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher
    D1-14 (CANL) - D1-16 (BAT)
    		Disconnect the negative auxiliary battery cable
    		1 MΩ or higher



OK
REPLACE TELEVISION CAMERA ECU
NG

REPLACE TELEVISION CAMERA ECU SUB BUS LINE OR CONNECTOR (CAN-H, CAN-L)