BACK DOOR GLASS > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation (Click here).



2. REMOVE REAR WIPER ARM AND BLADE ASSEMBLY

  1. Remove the nut, rear wiper arm and blade assembly.



3. REMOVE BACK DOOR TRIM BOARD (w/ Power Back Door)


    B109546E02

  1. Disengage the 3 claws and remove the back door trim board.



4. REMOVE BACK WINDOW PANEL TRIM UPPER (w/ Power Back Door)


    B109549E03

  1. Disengage the 2 claws and the 7 clips, and remove the back window panel trim upper.



5. REMOVE BACK WINDOW PANEL TRIM UPPER (w/o Power Back Door)


    B109547E01

  1. Disengage the 2 claws and the 7 clips, and remove the back window panel trim upper.



6. REMOVE BACK DOOR TRIM PANEL ASSEMBLY UPPER


    B109548E01

  1. Disengage the 10 clips and remove the back door trim panel assembly upper.



7. REMOVE BACK DOOR TRIM PANEL ASSEMBLY


    B109550E01

  1. Disengage the 8 clips and remove the back door trim panel assembly.



8. REMOVE BACK DOOR TRIM COVER RH


    B109551E01

  1. Disengage the 3 clips and remove the back door trim cover RH.

    HINT:
    If a clip remains on the door, remove the clip from the body and install it to the back door trim cover RH.



9. REMOVE BACK DOOR TRIM COVER LH


    B109552E01

  1. Disengage the 3 clips and remove the back door trim cover LH.

    HINT:
    If a clip remains on the door, remove the clip from the body and install it to the back door trim cover LH.



10. REMOVE REAR SPOILER SUB-ASSEMBLY


    B110039

  1. Disconnect the center stop light connector.

  1. Remove the 2 grommets and 5 bolts.



    B067937E01

  1. Remove the 3 clips and rear spoiler sub-assembly.



11. REMOVE REAR WIPER MOTOR ASSEMBLY


    E068272

  1. Disconnect the connector.

  1. Remove the 3 bolts and the rear wiper motor.



12. REMOVE REAR COMBINATION LIGHT ASSEMBLY LH


    E110464E01

  1. Disconnect the connector.

  1. Remove the 3 nuts.

  1. Disengage the 2 pins and remove the rear combination light assembly.



13. REMOVE REAR COMBINATION LIGHT ASSEMBLY RH


14. REMOVE BACK DOOR GLASS

  1. Disconnect the connector.



    B107774E01

  1. Pass a piano wire between the vehicle body and glass from the interior, as shown in the illustration.



    B106947E01

  1. Tie both wire ends to wooden blocks or similar objects.

    NOTICE:
    When separating the glass, take care not to damage the paint and interior and exterior ornaments.

    HINT:
    Apply protective tape to the outer surface to prevent the surface from being scratched.

  1. Cut off the adhesive by pulling the piano wire around the glass.

    NOTICE:
    If the back door glass will be reused, be careful not to damage the clip attached to the glass when you cut off the adhesive.

  1. Using a suction cup, remove the glass.

    NOTICE:
    Leave as much adhesive on the vehicle body as possible when removing the glass.



15. CLEAN BACK DOOR GLASS

  1. Using a scraper, remove the damaged stoppers, dam and adhesive sticking to the glass.



    B106929

  1. Clean the outer circumference of the glass with white gasoline.

    NOTICE:
    1. Do not touch the glass surface after cleaning it.
    2. Be careful not to damage the glass.
    3. Even if using a new glass, clean the glass with white gasoline.