ROOF HEADLINING > INSTALLATION

for Preparation Click here



1. INSTALL ROOF WIRE AND RADIO ANTENNA CORD


  1. Attach the roof wire, radio antenna cord and washer hose along the adhesive part.


    B111802E01

    NOTICE:
    Attach the roof wire, radio antenna cord and washer hose securely.

    HINT:
    Be careful that dirt or foreign objects do not stick to the adhesive part when removing the peeling paper.



2. INSTALL ROOF HEADLINING ASSEMBLY

  1. Place the roof headlining to the vehicle from the back door side.



  1. Engage the 2 fasteners and 3 clips. (w/o sliding roof)


    B111801E01

  1. Engage the 3 clips. (w/ sliding roof)

  1. Install the sunroof opening trim moulding. (w/ sliding roof)

  1. Connect the sliding roof drive gear connector. (w/ sliding roof)

  1. Connect the washer hose. Connect the radio antenna cord connector and engage the clamps to the rear quarter pillar RH.

  1. Connect the roof wire connector and engage the clamps to the front pillar LH.

  1. Connect the washer hose. Connect the radio antenna cord connector and engage the clamps to the front pillar RH.

  1. Install the radio antenna cord connector bolt to the front pillar RH.



3. INSTALL VISOR HOLDER


4. INSTALL LH VISOR ASSEMBLY

  1. Connect the connector.

  1. Install the visor assembly with the 2 screws.

  1. Engage the 4 claws and install the visor bracket cover.



5. INSTALL RH VISOR ASSEMBLY


6. INSTALL MAP LIGHT ASSEMBLY


    B110372

  1. Connect the connector.

  1. Install the map light with the 4 screws.



    B112055E01

  1. Engage the claws and install the 2 caps.



    B112053

  1. w/o sliding roof:
    Engage the 6 claws and install the lens cover.



    B112054

  1. w/ sliding roof:
    Engage the 8 claws and install the lens cover.



7. INSTALL ROOM LIGHT ASSEMBLY NO.1

  1. Connect the connector.

  1. Engage the 2 claws and 2 springs, and install the room light assembly No.1.



    B112052

  1. Engage the 4 claws and install the lens cover.



8. INSTALL RAIN SENSOR (W/ RAIN SENSOR)

  1. Connect the connector.

  1. Install the rain sensor.

    NOTICE:
    1. If there is any residue left from the silicon sheet on the windshield, remove it.
    2. Clean the dirt on the glass with a cloth etc.
    3. When installing a new rain sensor, peel the release paper off from the silicon sheet first.
    4. Be careful not to leave any air bubbles in the rain sensor when installing it.



9. INSTALL ASSIST GRIP SUB-ASSEMBLY

  1. Install the assist grip sub-assembly with the 2 screws.



    B113437

  1. Engage the 6 claws and install the 2 assist grip covers.

    HINT:
    Use the same procedure for the other 3 assist grips.



10. INSTALL ROOF SIDE LH GARNISH ASSEMBLY INNER


    B111796

  1. Engage the 7 clips and install the roof side garnish assembly inner.



    B111795

  1. Install the 3 clips.

  1. Install the 3 bolts and tonneau cover holder cap.



    B111797

  1. Engage the 4 claws and install the seat belt bezel.



11. INSTALL ROOF SIDE RH GARNISH ASSEMBLY INNER


12. INSTALL ROOM LIGHT ASSEMBLY NO.2


    B111794

  1. Connect the connector.

  1. Engage the claw and install the room light assembly No.2.



13. INSTALL DECK TRIM SIDE LH PANEL ASSEMBLY


    B111793

  1. Engage the 2 clips and install the deck trim side panel assembly.

  1. Install the 4 clips.



14. INSTALL DECK TRIM SIDE RH PANEL ASSEMBLY


15. INSTALL ROPE HOOK

  1. Install the 2 rope hooks with the 2 bolts.

    Torque:
    8.0 N*m{ 80 kgf*cm , 71 in.*lbf }

    HINT:
    Use the same procedure to install the other side.



16. INSTALL REAR FLOOR FINISH SIDE LH PLATE


    B111792

  1. Engage the 2 clips and install the rear floor finish side plate.

  1. Install the clip.



17. INSTALL REAR FLOOR FINISH SIDE RH PLATE


18. INSTALL REAR SEAT SIDE LH COVER


    B111791

  1. Engage the 4 clips and install the rear seat side cover.

  1. Install the 3 clips.



19. INSTALL REAR SEAT SIDE RH COVER


20. INSTALL REAR NO.1 SEAT OUTER LH BELT ASSEMBLY

  1. Install the rear No.1 seat outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



21. INSTALL REAR NO.1 SEAT OUTER RH BELT ASSEMBLY


22. INSTALL DECK SIDE TRIM LH COVER


    B111808

  1. Engage the 5 claws and install the deck side trim cover.



23. INSTALL DECK SIDE TRIM RH COVER


24. INSTALL CENTER PILLAR LH GARNISH


    B110479

  1. Engage the clip and install the center pillar garnish.

  1. Install the 2 screws.



25. INSTALL CENTER PILLAR RH GARNISH


26. INSTALL CENTER PILLAR LH GARNISH LOWER


    B111788

  1. Engage the 2 clips and 3 claws, install the center pillar garnish lower.



27. INSTALL CENTER PILLAR RH GARNISH LOWER


28. INSTALL FRONT SEAT OUTER LH BELT ASSEMBLY


    B111787

  1. Install the front seat outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



29. INSTALL FRONT SEAT OUTER RH BELT ASSEMBLY


30. INSTALL LAP BELT OUTER ANCHOR COVER


    B110478

  1. Engage the 2 claws and install the lap belt outer anchor cover as shown in the illustration.

    HINT:
    Use the same procedure to install the other side.



31. INSTALL FRONT PILLAR LH GARNISH


    B111800E01

  1. Install a new clip (A) on the front pillar garnish.

  1. Engage the 2 claws and 2 clips, and install the front pillar garnish.



32. INSTALL FRONT PILLAR RH GARNISH


33. INSTALL REAR DOOR OPENING TRIM LH WEATHERSTRIP


34. INSTALL REAR DOOR OPENING TRIM RH WEATHERSTRIP


35. INSTALL REAR DOOR SCUFF LH PLATE


    B111783

  1. Connect the connector. (w/ illumination scuff plate)

  1. Engage the 4 claws and 2 clips, and install the rear door scuff plate.



36. INSTALL REAR DOOR SCUFF RH PLATE


37. INSTALL FRONT DOOR OPENING TRIM LH WEATHERSTRIP


38. INSTALL FRONT DOOR OPENING TRIM RH WEATHERSTRIP


39. INSTALL FRONT DOOR SCUFF LH PLATE


    B111782

  1. Connect the connector. (w/ illumination scuff plate)

  1. Engage the 6 claws and 4 clips, and install the front door scuff plate.



40. INSTALL FRONT DOOR SCUFF RH PLATE


41. INSTALL REAR SEAT ASSEMBLY RH

  1. Place the rear seat assembly RH in the vehicle and align the adjuster pin with the hole on the vehicle side.

  1. Move the rear seat assembly RH to the rearmost position by operating the rear seat track adjusting handle.

    NOTICE:
    Check that the seat is locked.

  1. Temporarily install the front side of the rear seat assembly RH with the 2 bolts.

  1. Recline the separate rear seatback forward by operating the rear seat lock control lever sub-assembly.

  1. Move the rear seat assembly RH fully forward.

    NOTICE:
    Check that the seat is locked.

  1. Temporarily install the rear side of the rear seat assembly RH with the 3 bolts.

  1. Return the separate rear seatback to the upright position.

  1. Move the rear seat assembly RH to the rearmost position by operating the rear seat track adjusting handle.

    NOTICE:
    Check that the seat is locked.

  1. Fully tighten the 2 bolts on the front side of the rear seat assembly RH in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Recline the separate rear seatback forward by operating the rear seat lock control lever sub-assembly.

  1. Move the rear seat assembly RH fully forward.

    NOTICE:
    Check that the seat is locked.

  1. Fully tighten the 3 bolts on the rear side of the rear seat assembly RH in the order of the inner rear side bolt, the inner front side bolt, and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Return the separate rear seatback to the upright position.

  1. Move the rear seat assembly RH to the rearmost position by operating the rear seat track adjusting handle.

    NOTICE:
    Check that the seat is locked.

  1. Install the floor anchor side of the fold seat stopper band assembly No.1 with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Install the 5 clips.



42. INSTALL REAR SEAT TRACK BRACKET COVER


43. INSTALL REAR SEAT ASSEMBLY LH

  1. Place the rear seat assembly LH in the vehicle and align the adjuster pin with the hole on the vehicle side.

  1. Move the rear seat assembly LH to the rearmost position by operating the rear seat track adjusting handle.

    NOTICE:
    Check that the seat is locked.

  1. Temporarily install the front side of the rear seat assembly LH with the 2 bolts.

  1. Recline the separate rear seatback forward by operating the rear seat lock control lever sub-assembly.

  1. Move the rear seat assembly LH fully forward.

    NOTICE:
    Check that the seat is locked.

  1. Temporarily install the rear side of the rear seat assembly LH with the 3 bolts.

  1. Return the separate rear seatback to the upright position.

  1. Move the rear seat assembly LH to the rearmost position by operating the rear seat track adjusting handle.

    NOTICE:
    Check that the seat is locked.

  1. Fully tighten the 2 bolts on the front side of the rear seat assembly LH in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Recline the separate rear seatback forward by operating the rear seat lock control lever sub-assembly.

  1. Move the rear seat assembly LH fully forward.

    NOTICE:
    Check that the seat is locked.

  1. Fully tighten the 3 bolts on the rear side of the rear seat assembly LH in the order of the inner rear side bolt, the inner front side bolt, and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Return the separate rear seatback to the upright position.

  1. Move the rear seat assembly LH to the rearmost position by operating the rear seat track adjusting handle.

    NOTICE:
    Check that the seat is locked.

  1. Install the floor anchor side of the fold seat stopper band assembly No.2 with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Install the 3 clips.



44. INSTALL REAR SEAT TRACK BRACKET COVER


45. INSTALL DECK SIDE TRIM LH BOX


    B111781

  1. Install the deck side trim box with the 2 clips.



46. INSTALL DECK SIDE TRIM RH BOX


47. INSTALL JACK CARRIER ASSEMBLY

  1. Install the jack carrier assembly, jack assembly and jack carrier support.



48. INSTALL REAR FLOOR FINISH PLATE


    B110477

  1. Engage the 2 claws and 6 clips, and install the rear floor finish plate.

  1. Install the 2 clips.



49. INSTALL BACK DOOR WEATHERSTRIP


50. INSTALL DECK NO.3 BOARD SUB-ASSEMBLY


    B110025

  1. Install the deck No.3 board sub-assembly with the 2 bolts and 2 nuts.



51. INSTALL DECK NO.2 BOARD SUB-ASSEMBLY


    B110024

  1. Install the deck No.2 board sub-assembly with the 4 bolts and 2 nuts.



52. INSTALL DECK FLOOR BOX REAR


    B110023

  1. Install the deck floor box rear with the 2 clips.



53. INSTALL DECK FLOOR BOX FRONT


    B110022

  1. Install the deck floor box front with the 2 clips.



54. INSTALL DECK BOARD SUB-ASSEMBLY


    B110455

  1. Install the deck board sub-assembly with the 2 bolt.

  1. Engage the 5 clips.



55. INSTALL TONNEAU COVER ASSEMBLY


56. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


57. PERFORM INITIALIZATION
(Click here)


58. INSPECT SLIDE ADJUSTER LOCK

  1. Check that the left and right adjusters lock simultaneously when sliding the seat.

  1. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.