PARKING BRAKE PEDAL (for LHD) > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
Wait for 90 seconds after disconnecting the cable to prevent the airbag working.



2. REMOVE SEAT TRACK BRACKET COVER OUTER FRONT LH


    B112092E01

  1. Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.

  1. Using a screwdriver, disengage the 3 claws and remove the seat track bracket cover outer front LH.

    HINT:
    Tape the screwdriver tip before use.



3. REMOVE SEAT TRACK BRACKET COVER INNER FRONT LH


    B112093E01

  1. Using a screwdriver, disengage the 2 claws and remove the seat track bracket cover inner front LH.

    HINT:
    Tape the screwdriver tip before use.



4. REMOVE SEAT TRACK COVER RH

  1. Using a screwdriver, disengage the 4 claws and remove the seat track cover RH.

    HINT:
    Tape the screwdriver tip before use.



5. REMOVE SEAT TRACK COVER LH


    B112094E01

  1. Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.

  1. Using a screwdriver, disengage the 4 claws and remove the seat track cover LH.

    HINT:
    Tape the screwdriver tip before use.



6. REMOVE FRONT SEAT ASSEMBLY

  1. Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.

  1. Remove the 2 bolts on the front side.

  1. Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.

  1. Remove the 2 bolts on the rear side.

  1. Move the front seat assembly to the center position and adjust the seatback to the vertical position by operating the slide and vertical power seat switch knob and the reclining power seat switch knob.

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative battery cable from the battery, and wait 90 seconds or more.

    CAUTION:
    Wait 90 seconds or more after disconnecting the negative terminal cable to prevent the airbag from working (Click here ).

  1. Disconnect the connectors and clamp.

  1. Remove the front seat assembly.

    NOTICE:
    When removing the passenger side front seat assembly, be careful not to step on the yaw rate sensor mounted on the floor under the seat.



7. REMOVE FRONT DOOR SCUFF PLATE


    B111782

  1. Disengage the 6 claws and 4 clips, and remove the front door scuff plate.

  1. Disconnect the connector. (w/ illumination scuff plate)



8. REMOVE COWL SIDE TRIM SUB-ASSEMBLY


    B108509

  1. Remove the 2 clips and the cowl side trim sub-assembly LH.



9. REMOVE INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LOWER


    B108510E02

  1. Using a screwdriver, open the instrument panel finish panel sub-assembly lower cover.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the bolt <A> and the screw <C>.

  1. Disconnect the hood lock control cable assembly.

  1. Disengage the 5 claws and the 4 clips.

  1. Disconnect the connectors and then remove the instrument panel finish panel sub-assembly lower.



10. REMOVE FLOOR CARPET COVER CENTER


    B108514

  1. Remove the 2 clips from the floor carpet cover center LH.

  1. Depress the edge of the floor carpet cover center LH around the claws to disengage the 2 claws below the floor carpet cover center LH.

  1. Slide the floor carpet cover center LH to the front of the vehicle, and disengage the 2 claws from the instrument panel finish panel lower center at the floor carpet center LH.

  1. Remove the floor carpet cover center LH.



11. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY


    C111085

  1. Disconnect the connector from the driver side knee airbag assembly.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Remove the 4 bolts and the driver side knee airbag assembly.



12. REMOVE FLOOR FOOTREST

  1. Remove the 2 clips and floor footrest.



13. REMOVE PARKING BRAKE PEDAL


    C108688

  1. Remove the 2 bolts and separate the parking brake No.2 and No.3 cable assemblies from the parking brake equalizer.



    C108717E01

  1. Slide the rubber boot as shown in the illustration.



    C108689

  1. Remove the parking brake equalizer from the parking brake No.1 cable assembly.



    C110874E01

  1. Disengage the 2 clamps and separate the wiring harness protector cover.

  1. Remove the 3 nuts and separate the instrument panel junction block assembly from the body.



    C110875

  1. Remove the 2 bolts and 2 nuts, and separate the parking brake No.1 cable assembly from the body.



    C110876E01

  1. Disconnect the connector and clamp.

  1. Remove the 3 nuts and parking brake pedal from the body.