FRONT SEAT ASSEMBLY > REASSEMBLY

for Preparation Click here

1. Using a "torx" socket wrench (T40), install the separate type front seat cushion spring assembly with the 4 "torx" bolts.
   

2. Install the front seat cushion frame sub-assembly with the 4 bolts.
   

   Torque:

   19 N*m{ 194 kgf*cm , 14 ft.*lbf }

1. Install the front seat side airbag assembly with the 2 nuts.
   

   Torque:

   5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

2. Install the clamps.
   

1. Check that the ignition switch is off.
   

2. Check that the negative battery (-) terminal is disconnected.
   

   CAUTION:

   After disconnecting the negative battery terminal, wait for at least 90 seconds before starting the operation.

3. Using a feeler gauge 1 mm (0.039 in.), install the seat position sensor.
   

   NOTICE:

   1. If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
      
   2. When installing the seat position sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.
      

   HINT:

   Be sure that a clearance between the seat position sensor and the seat rail is within 0.6 mm (0.023 in.) to 1.4 mm (0.055 in.).

4. Using a "torx" socket wrench (T30), tighten the "torx" screw to install the seat position sensor.
   

   Torque:

   8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

5. Make sure that a clearance between the seat position sensor and the seat rail is within 0.6 mm (0.023 in.) to 1.4 mm (0.055 in.).
   

6. Check that there is no looseness in the installation parts of the seat position sensor.
   

7. Connect the connector to the seat position sensor.
   

1. Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with new hog rings.
   

   NOTICE:

   1. Be careful not to damage the cover.
      
   2. When installing the hog rings, take care to minimize wrinkles as much as possible.
      

1. Install the separate type front seatback cover with pad to the separate type front seat cushion spring assembly.
   

2. Install the separate type front seatback cover bracket with the nut.
   

   Torque:

   5.6 N*m{ 57 kgf*cm , 50 in.*lbf }

   NOTICE:

   1. For vehicles with side airbags, the side airbags may not be activated normally unless the separate type front seatback cover is securely installed.
      
   2. Check that the strap is not twisted after installing the bracket.
      
   3. Install the bracket securely.
      

3. Install the hook.
   

1. Install the seat armrest assembly with the bolt and 2 washers.
   

   Torque:

   37 N*m{ 377 kgf*cm , 27 ft.*lbf }

1. Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with new hog rings.
   

   NOTICE:

   1. Be careful not to damage the cover.
      
   2. When installing the hog rings, take care to minimize wrinkles as much as possible.
      

1. Install the front seat inner belt assembly with the nut.
   

   Torque:

   42 N*m{ 428 kgf*cm , 31 ft.*lbf }

   NOTICE:

   Do not allow the anchor part of the front seat inner belt assembly and the protruding part of the front seat adjuster to overlap.

2. Install the 4 clamps.
   

3. Connect the connectors.