REAR SEAT INNER BELT ASSEMBLY > INSTALLATION

for Preparation Click here

1. Install the rear seat belt assembly inner with the bolt.
   

   Torque:

   42 N*m{ 428 kgf*cm , 31 ft.*lbf }

1. Install the 2 bolts.
   

   Torque:

   18 N*m{ 184 kgf*cm , 13 ft.*lbf }

2. Install the 2 rubber bands on the backside of the rear seatback board carpet assembly.
   

3. Using a "torx" socket wrench (T45), install the separate type rear seat cushion assembly with the 2 "torx" bolts.
   

   Torque:

   21 N*m{ 214 kgf*cm , 16 ft.*lbf }

1. Place the rear seat assembly LH in the vehicle and align the adjuster pin with the hole on the vehicle side.
   

2. Move the rear seat assembly LH to the rearmost position by operating the rear seat track adjusting handle.
   

   NOTICE:

   Check that the seat is locked.

3. Temporarily install the front side of the rear seat assembly LH with the 2 bolts.
   

4. Recline the separate rear seatback forward by operating the rear seat lock control lever sub-assembly.
   

5. Move the rear seat assembly LH fully forward.
   

   NOTICE:

   Check that the seat is locked.

6. Temporarily install the rear side of the rear seat assembly LH with the 3 bolts.
   

7. Return the separate rear seatback to the upright position.
   

8. Move the rear seat assembly LH to the rearmost position by operating the rear seat track adjusting handle.
   

   NOTICE:

   Check that the seat is locked.

9. Fully tighten the 2 bolts on the front side of the rear seat assembly LH in the order of the inner side bolt and then the outer side bolt.
   

   Torque:

   37 N*m{ 377 kgf*cm , 27 ft.*lbf }

10. Recline the separate rear seatback forward by operating the rear seat lock control lever sub-assembly.
    

11. Move the rear seat assembly LH fully forward.
    

    NOTICE:

    Check that the seat is locked.

12. Fully tighten the 3 bolts on the rear side of the rear seat assembly LH in the order of the inner rear side bolt, the inner front side bolt, and then the outer side bolt.
    

    Torque:

    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

13. Return the separate rear seatback to the upright position.
    

14. Move the rear seat assembly LH to the rearmost position by operating the rear seat track adjusting handle.
    

    NOTICE:

    Check that the seat is locked.

15. Install the floor anchor side of the fold seat stopper band assembly No.2 with the bolt.
    

    Torque:

    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

16. Install the 3 clips.
    

1. Check that the left and right adjusters lock simultaneously when sliding the seat.
   

2. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.
   

1. Temporarily install the center seatback assembly with the 3 bolts and "torx" bolt.
   

2. Tighten the 3 bolts.
   

   Torque:

   21 N*m{ 214 kgf*cm , 16 ft.*lbf }

3. Using a "torx" socket wrench (T45), tighten the "torx" bolt.
   

   Torque:

   21 N*m{ 214 kgf*cm , 16 ft.*lbf }

4. Install the screw.
   

1. Install the center seat assembly with the 4 bolts.
   

   Torque:

   21 N*m{ 214 kgf*cm , 16 ft.*lbf }

2. Install new hog rings.