REAR SEAT OUTER BELT ASSEMBLY > INSTALLATION

for Preparation Click here

1. Check the degree of tilt when the ELR begins to lock.
   
   

   1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.
      

      NOTICE:

      Do not disassemble the retractor.

2. Install the rear seat outer belt assembly with the 2 bolts.
   

   Torque:

   For upper bolt:

   7.5 N*m{ 77 kgf*cm , 66 in.*lbf }

   For lower bolt:

   42 N*m{ 428 kgf*cm , 31 ft.*lbf }

3. Connect the shoulder side of the rear seat outer belt assembly with the bolt.
   

   Torque:

   42 N*m{ 428 kgf*cm , 31 ft.*lbf }

1. Engage the 7 clips and install the roof side garnish assembly inner.
   

2. Install the 3 clips.
   

3. Install the 3 bolts and tonneau cover holder cap.
   

4. Engage the 4 claws and install the seat belt bezel.
   

1. Connect the connector.
   

2. Engage the claw and install the room light assembly No.2.
   

1. Engage the 2 clips and install the deck trim side panel assembly.
   

2. Install the 4 clips.
   

1. Install the 2 rope hooks with the 2 bolts.
   

   Torque:

   8.0 N*m{ 80 kgf*cm , 71 in.*lbf }

   HINT:

   Use the same procedure to install the other side.

1. Engage the 2 clips and install the rear floor finish side plate.
   

2. Install the clip.
   

1. Engage the 4 clips and install the rear seat side cover.
   

2. Install the 3 clips.
   

1. Connect the floor side of the rear seat outer belt assembly with the bolt.
   

   Torque:

   42 N*m{ 428 kgf*cm , 31 ft.*lbf }

   NOTICE:

   Do not allow the anchor part of the rear seat outer belt assembly and the protruding parts of the floor panel to overlap.

2. Check if the ELR locks.
   

   NOTICE:

   The check should be performed with the outer belt assembly installed.

   
   

   1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
      

1. Engage the 5 claws and install the deck side trim cover.
   

1. Connect the connector. (w/ illumination scuff plate)
   

2. Engage the 4 claws and 2 clips, and install the rear door scuff plate.
   

1. Install the deck side trim box with the 2 clips.
   

1. Engage the 2 claws and 6 clips, and install the rear floor finish plate.
   

2. Install the 2 clips.
   

1. Install the deck No.2 board sub-assembly with the 4 bolts and 2 nuts.
   

1. Install the deck No.3 board sub-assembly with the 2 bolts and 2 nuts.
   

1. Install the deck floor box rear with the 2 clips.
   

1. Install the deck floor box front with the 2 clips.
   

1. Install the deck board sub-assembly with the 2 bolt.
   

2. Engage the 5 clips.
   

1. Place the rear seat assembly LH in the vehicle and align the adjuster pin with the hole on the vehicle side.
   

2. Move the rear seat assembly LH to the rearmost position by operating the rear seat track adjusting handle.
   

   NOTICE:

   Check that the seat is locked.

3. Temporarily install the front side of the rear seat assembly LH with the 2 bolts.
   

4. Recline the separate rear seatback forward by operating the rear seat lock control lever sub-assembly.
   

5. Move the rear seat assembly LH fully forward.
   

   NOTICE:

   Check that the seat is locked.

6. Temporarily install the rear side of the rear seat assembly LH with the 3 bolts.
   

7. Return the separate rear seatback to the upright position.
   

8. Move the rear seat assembly LH to the rearmost position by operating the rear seat track adjusting handle.
   

   NOTICE:

   Check that the seat is locked.

9. Fully tighten the 2 bolts on the front side of the rear seat assembly LH in the order of the inner side bolt and then the outer side bolt.
   

   Torque:

   37 N*m{ 377 kgf*cm , 27 ft.*lbf }

10. Recline the separate rear seatback forward by operating the rear seat lock control lever sub-assembly.
    

11. Move the rear seat assembly LH fully forward.
    

    NOTICE:

    Check that the seat is locked.

12. Fully tighten the 3 bolts on the rear side of the rear seat assembly LH in the order of the inner rear side bolt, the inner front side bolt, and then the outer side bolt.
    

    Torque:

    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

13. Return the separate rear seatback to the upright position.
    

14. Move the rear seat assembly LH to the rearmost position by operating the rear seat track adjusting handle.
    

    NOTICE:

    Check that the seat is locked.

15. Install the floor anchor side of the fold seat stopper band assembly No.2 with the bolt.
    

    Torque:

    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

16. Install the 3 clips.
    

1. Check that the left and right adjusters lock simultaneously when sliding the seat.
   

2. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.