REAR SHOCK ABSORBER > INSTALLATION

for Preparation Click here



1. INSTALL REAR SHOCK ABSORBER WITH COIL SPRING

  1. Install the rear shock absorber with coil spring to the rear axle carrier assembly and insert the 2 bolts from the rear side of the vehicle.



    C107307E01

  1. Slowly jack up the vehicle using a wooden block and install the rear shock absorber with coil spring (upper side) to the vehicle.



    C107463

  1. Install the 3 nuts to the upper side of rear shock absorber with coil spring.

    Torque:
    58 N*m{ 591 kgf*cm , 43 ft.*lbf }



    C107670E01

  1. Install the 2 nuts to the lower side of rear shock absorber with coil spring.

    Torque:
    180 N*m{ 1,840 kgf*cm , 133 ft.*lbf }

    NOTICE:
    When installing the nuts, keep the bolts from rotating.



    C107466E01

  1. Fully tighten the lock nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



2. CONNECT REAR SPEED SENSOR


    C107669E01

  1. Install the rear brake flexible hose and rear speed sensor with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf } (bolt A)
    19 N*m{ 194 kgf*cm , 14 ft.*lbf } (bolt B)
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf } (bolt C)



3. INSTALL REAR STABILIZER LINK ASSEMBLY


    C107308

  1. Install the rear stabilizer link assembly to the rear shock absorber with the nut.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud.



4. INSTALL DECK TRIM SIDE PANEL ASSEMBLY


    B111793

  1. Engage the 2 clips and install the deck trim side panel assembly.

  1. Install the 4 clips.



5. INSTALL REAR FLOOR FINISH SIDE PLATE


    B111792

  1. Engage the 2 clips and install the rear floor finish side plate.

  1. Install the clip.



6. INSTALL REAR SEAT SIDE COVER


    B111791

  1. Engage the 4 clips and install the rear seat side cover.

  1. Install the 3 clips.



7. INSTALL DECK SIDE TRIM COVER


    B111808

  1. Engage the 5 claws and install the deck side trim cover.



8. INSTALL REAR DOOR SCUFF PLATE


    B111791

  1. Engage the 4 clips and install the rear seat side cover.

  1. Install the 3 clips.



9. INSTALL DECK SIDE TRIM BOX LH


    B111781

  1. Install the deck side trim box with the 2 clips.



10. INSTALL DECK SIDE TRIM BOX RH


11. INSTALL JACK CARRIER ASSEMBLY


12. INSTALL JACK ASSEMBLY


13. INSTALL JACK CARRIER SUPPORT


14. INSTALL REAR FLOOR FINISH PLATE


    B110477

  1. Engage the 2 claws and 6 clips, and install the rear floor finish plate.

  1. Install the 2 clips.



15. INSTALL DECK NO.3 BOARD SUB-ASSEMBLY


    B110025

  1. Install the deck No.3 board sub-assembly with the 2 bolts and 2 nuts.



16. INSTALL DECK NO.2 BOARD SUB-ASSEMBLY


    B110024

  1. Install the deck No.2 board sub-assembly with the 4 bolts and 2 nuts.



17. INSTALL REAR DECK FLOOR BOX


    B110023

  1. Install the deck floor box rear with the 2 clips.



18. INSTALL FRONT DECK FLOOR BOX


    B110022

  1. Install the deck floor box front with the 2 clips.



19. INSTALL DECK BOARD SUB-ASSEMBLY


    B110455

  1. Install the deck board sub-assembly with the 2 bolt.

  1. Engage the 5 clips.



20. CHECK ABS SPEED SENSOR SIGNAL
(Click here)


21. INSTALL REAR WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }



22. INSPECT AND ADJUST REAR WHEEL ALIGNMENT
(Click here)