POWER SEAT SWITCH > INSPECTION

for Preparation Click here



1. INSPECT FRONT POWER SEAT SWITCH


    B105970E03

  1. Inspect the LH side power seat switch.

    1. Measure the resistance according to the value(s) in the table below.

      Resistance:
      Slide switch:
      Tester Connection
      		Switch Condition
      		Specified Condition
      1(B) - 9(SLDF)
      		FRONT
      		Below 1 Ω
      4(E) - 6(SLDR)
      		FRONT
      		Below 1 Ω
      4(E) - 6(SLDR)
      		OFF
      		Below 1 Ω
      4(E) - 9(SLDF)
      		OFF
      		Below 1 Ω
      1(B) - 6(SLDR)
      		REAR
      		Below 1 Ω
      4(E) - 9(SLDF)
      		REAR
      		Below 1 Ω
      Front vertical switch:
      Tester Connection
      		Switch Condition
      		Specified Condition
      1(B) - 10(FUP)
      		UP
      		Below 1 Ω
      4(E) - 5(FDWN)
      		UP
      		Below 1 Ω
      4(E) - 5(FDWN)
      		OFF
      		Below 1 Ω
      4(E) - 10(FUP)
      		OFF
      		Below 1 Ω
      1(B) - 5(FDWN)
      		DOWN
      		Below 1 Ω
      4(E) - 10(FUP)
      		DOWN
      		Below 1 Ω
      Lifter switch:
      Tester Connection
      		Switch Condition
      		Specified Condition
      1(B) - 7(LUP)
      		UP
      		Below 1 Ω
      4(E) - 8(LDWN)
      		UP
      		Below 1 Ω
      4(E) - 7(LUP)
      		OFF
      		Below 1 Ω
      4(E) - 8(LDWN)
      		OFF
      		Below 1 Ω
      1(B) - 8(LDWN)
      		DOWN
      		Below 1 Ω
      4(E) - 7(LUP)
      		DOWN
      		Below 1 Ω
      Reclining switch:
      Tester Connection
      		Switch Condition
      		Specified Condition
      1(B) - 3(RCLF)
      		FRONT
      		Below 1 Ω
      2(RCLR) - 4(E)
      		FRONT
      		Below 1 Ω
      2(RCLR) - 4(E)
      		OFF
      		Below 1 Ω
      3(RCLF) - 4(E)
      		OFF
      		Below 1 Ω
      1(B) - 2(RCLR)
      		REAR
      		Below 1 Ω
      3(RCLF) - 4(E)
      		REAR
      		Below 1 Ω

      If the result is not as specified, replace the switch.



    B105969E02

  1. Inspect the RH side power seat switch.

    1. Measure the resistance according to the value(s) in the table below.

      Resistance:
      Slide switch:
      Tester Connection
      		Switch Condition
      		Specified Condition
      1(B) - 9(SLDF)
      		FRONT
      		Below 1 Ω
      4(E) - 6(SLDR)
      		FRONT
      		Below 1 Ω
      4(E) - 6(SLDR)
      		OFF
      		Below 1 Ω
      4(E) - 9(SLDF)
      		OFF
      		Below 1 Ω
      1(B) - 6(SLDR)
      		REAR
      		Below 1 Ω
      4(E) - 9(SLDF)
      		REAR
      		Below 1 Ω
      Front vertical switch:
      Tester Connection
      		Switch Condition
      		Specified Condition
      1(B) - 5(FUP)
      		UP
      		Below 1 Ω
      4(E) - 10(FDWN)
      		UP
      		Below 1 Ω
      4(E) - 5(FUP)
      		OFF
      		Below 1 Ω
      4(E) - 10(FDWN)
      		OFF
      		Below 1 Ω
      1(B) - 10(FDWN)
      		DOWN
      		Below 1 Ω
      4(E) - 5(FUP)
      		DOWN
      		Below 1 Ω
      Lifter switch:
      Tester Connection
      		Switch Condition
      		Specified Condition
      1(B) - 8(LUP)
      		UP
      		Below 1 Ω
      4(E) - 7(LDWN)
      		UP
      		Below 1 Ω
      4(E) - 7(LDWN)
      		OFF
      		Below 1 Ω
      4(E) - 8(LUP)
      		OFF
      		Below 1 Ω
      1(B) - 7(LDWN)
      		DOWN
      		Below 1 Ω
      4(E) - 8(LUP)
      		DOWN
      		Below 1 Ω
      Reclining switch:
      Tester Connection
      		Switch Condition
      		Specified Condition
      1(B) - 3(RCLF)
      		FRONT
      		Below 1 Ω
      2(RCLR) - 4(E)
      		FRONT
      		Below 1 Ω
      2(RCLR) - 4(E)
      		OFF
      		Below 1 Ω
      3(RCLF) - 4(E)
      		OFF
      		Below 1 Ω
      1(B) - 2(RCLR)
      		REAR
      		Below 1 Ω
      3(RCLF) - 4(E)
      		REAR
      		Below 1 Ω

      If the result is not as specified, replace the switch.