BACK DOOR > DISASSEMBLY

for Preparation Click here



1. REMOVE REAR WIPER ARM COVER

  1. Remove rear wiper arm cover.



2. REMOVE REAR WIPER ARM AND BLADE ASSEMBLY

  1. Remove the nut, rear wiper arm and blade assembly.



3. REMOVE REAR WIPER SHAFT COVER


    E108668

  1. Remove the rear wiper shaft cover.



4. REMOVE REAR NO.1 WIPER LINK PIVOT NUT


    E108667

  1. Using the socket wrench 27 mm (1.06 in.), remove the rear No.1 wiper link pivot nut.



5. REMOVE REAR NO.1 WIPER LINK PIVOT WASHER


    E108669

  1. Remove the rear No.1 wiper link pivot washer.



6. REMOVE BACK WINDOW PANEL TRIM UPPER (w/o Power Back Door)


    B109547E01

  1. Disengage the 2 claws and the 7 clips, and remove the back window panel trim upper.



7. REMOVE BACK DOOR TRIM BOARD (w/ Power Back Door)


    B109546E02

  1. Disengage the 3 claws and remove the back door trim board.



8. REMOVE BACK WINDOW PANEL TRIM UPPER (w/ Power Back Door)


    B109549E03

  1. Disengage the 2 claws and the 7 clips, and remove the back window panel trim upper.



9. REMOVE BACK DOOR TRIM PANEL ASSEMBLY UPPER


    B109548E01

  1. Disengage the 10 clips and remove the back door trim panel assembly upper.



10. REMOVE BACK DOOR TRIM PANEL ASSEMBLY


    B109550E01

  1. Disengage the 8 clips and remove the back door trim panel assembly.



11. REMOVE REAR WIPER MOTOR ASSEMBLY


    E068272

  1. Disconnect the connector.

  1. Remove the 3 bolts and the rear wiper motor.



12. REMOVE BACK-UP LIGHT ASSEMBLY RH


    E108656E01

  1. Disconnect each connector.

  1. Remove the 3 nuts and disengage the clip, and remove the back-up light assembly.



13. REMOVE BACK-UP LIGHT ASSEMBLY LH


    E108656E01

  1. Disconnect each connector.

  1. Remove the 3 nuts and disengage the clip, and remove the back-up light assembly.



14. REMOVE BACK DOOR TRIM COVER RH


    B109551E01

  1. Disengage the 3 clips and remove the back door trim cover RH.

    HINT:
    If a clip remains on the door, remove the clip from the body and install it to the back door trim cover RH.



15. REMOVE BACK DOOR TRIM COVER LH


    B109552E01

  1. Disengage the 3 clips and remove the back door trim cover LH.

    HINT:
    If a clip remains on the door, remove the clip from the body and install it to the back door trim cover LH.



16. REMOVE REAR SPOILER SUB-ASSEMBLY


    B110039

  1. Disconnect the center stop light connector.

  1. Remove the 2 grommets and 5 bolts.



    B067937E01

  1. Remove the 3 clips and rear spoiler sub-assembly.



17. REMOVE BACK DOOR TRIM SPACER (RH Side)

  1. Remove the screw.



    B109554E01

  1. Disengage the clip and remove the back door trim spacer.



18. REMOVE BACK DOOR TRIM SPACER (LH Side)

  1. Remove the screw.



    B109553E01

  1. Disengage the clip and remove the back door trim spacer.



19. REMOVE BACK DOOR LOCK COVER


    B109555E01

  1. Disengage the 4 claws and remove the back door lock cover.



20. REMOVE BACK DOOR LOCK ASSEMBLY (w/o Power Back Door)


    B109800

  1. Separate the link rod as shown in the illustration.



    B109556E01

  1. Disconnect the connector and remove the clamp.

  1. Remove the 3 bolts and the back door lock assembly.



21. REMOVE BACK DOOR LOCK ASSEMBLY (w/ Power Back Door)


    B109800

  1. Separate the link rod as shown in the illustration.



    B109557E01

  1. Disconnect each connector and remove the clamp.

  1. Remove the 4 bolts and the back door lock assembly.



22. REMOVE POWER BACK DOOR SENSOR ASSEMBLY RH (w/ Power Back Door)


    B109561E01

  1. Disconnect the connector.

  1. Remove the clip.

  1. Using a "torx" socket wrench (T30), remove the 3 screws and the power back door sensor assembly RH.



23. REMOVE POWER BACK DOOR SENSOR ASSEMBLY LH (w/ Power Back Door)


    B109560E01

  1. Disconnect the connector.

  1. Remove the clip.

  1. Using a "torx" socket wrench (T30), remove the 3 screws and the power back door sensor assembly LH.



24. REMOVE BACK DOOR GARNISH

  1. Disengage the back door opener switch connector.



  1. Remove the 5 bolts, clip and garnish.


    B068610E01



25. REMOVE BACK DOOR OPENER SWITCH ASSEMBLY


    B109806E01

  1. Remove the 2 screws.

  1. Disengage the 2 clamps and remove the back door opener switch assembly.



26. REMOVE TELEVISION CAMERA (w/ Back Guide Monitor System)


    E111288E01

  1. Disconnect the connector and disengage the clamp.



    E111976

  1. Disengage the 2 claws and remove the television camera.



27. REMOVE LICENSE PLATE LIGHT ASSEMBLY


    E068324E01

  1. Disengage the 2 claws and separate the license plate light assembly as shown in the illustration.

  1. Disconnect the connector and remove the license plate light assembly.



28. REMOVE POWER BACK DOOR WARNING BUZZER (w/ Power Back Door)


    B109559E01

  1. Disconnect the connector.

  1. Remove the clamp and power back door warning buzzer.



29. REMOVE POWER BACK DOOR CONTROL SWITCH ASSEMBLY (w/ Power Back Door)


    B109558E01

  1. Remove the clamp and disconnect the connector.

  1. Disengage the 2 claws and remove the power back door control switch assembly as shown in the illustration.



30. REMOVE DOOR PULL HANDLE


    B109563E01

  1. Disengage the 4 claws and remove the door pull handle.