POWER MIRROR CONTROL SYSTEM (w/ Memory) > TERMINALS OF ECU

for Preparation Click here



CHECK OUTER MIRROR CONTROL ECU LH

B069728E04

  1. Disconnect the R17 connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Standard voltage:

    Symbols (Terminal No.)
    		Wiring Color
    		Terminal Description
    		Condition
    		Specified Condition
    BDR (P17-3) - Body ground
    		G - Body ground
    		+B power supply
    		Always
    		10 to 14 V
    CPUB (P17-7) - Body ground
    		L-B - Body ground
    		+B power supply
    		Always
    		10 to 14 V
    SIG (P17-8) - Body ground
    		GR - Body ground
    		Ignition power supply
    		Ignition switch OFF → ON
    		0 V → 10 to 14 V


    Standard resistance:

    Symbols (Terminal No.)
    		Wiring Color
    		Terminal Description
    		Condition
    		Specified Condition
    GND (P27-1) - Body ground
    		W-B - Body ground
    		Ground
    		Always
    		Below 1 Ω

    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the R17 connector.

  4. Measure the voltage according to the value(s) in the table below.

    Standard voltage:

    Symbols (Terminal No.)
    		Wiring Color
    		Terminal Description
    		Condition
    		Specified Condition
    LMVR (R22-1) - Body ground
    		V - Body ground
    		Outer mirror switch signal (Up or Right)
    		Ignition switch ACC, Left/Right adjustment switch L side, Mirror switch OFF→ UP or Right
    		0 V → 10 to 14 V
    HTR+ (R22-4) - HTR- (R22-12)
    		B - B
    		Mirror heater signal
    		Mirror heater switch ON
    		0 V → 10 to 14 V
    LVC (R22-5) - Body ground
    		R-W - Body ground
    		Power source for mirror position sensor
    		Ignition switch OFF → ACC
    		0 V → 0 to 5 V
    VSSR (R22-6) - Body ground
    		Y-B - Body ground
    		Vertical direction position signal
    		Ignition switch ACC, Left/Right adjustment switch L side, Mirror switch uppermost position → lowermost position
    		0 V → 1 to 3V
    LMHR (R22-9) - Body ground
    		BR - Body ground
    		Outer mirror switch signal (Left or Down)
    		Ignition switch ACC, Left/Right adjustment switch L side, Mirror switch OFF→ LEFT or DOWN
    		0 V → 10 to 14 V
    LM+R (R22-10) - Body ground
    		R - Body ground
    		Outer mirror switch signal (Right or Down)
    		Ignition switch ACC, Left/Right adjustment switch L side, Mirror switch OFF→ RIGHT or DOWN
    		0 V → 10 to 14 V
    HSSR (R22-13) - Body ground
    		P - Body ground
    		Horizontal direction position signal
    		Ignition switch ACC, Left/Right adjustment switch L side, Mirror switch innermost position → outermost position
    		0 V → 1 to 3 V


CHECK OUTER MIRROR CONTROL ECU RH

B069726E05

  1. Disconnect the R18 connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Standard voltage:

    Symbols (Terminal No.)
    		Wiring Color
    		Terminal Description
    		Condition
    		Specified Condition
    BDR (P18-3) - Body ground
    		G - Body ground
    		+B power supply
    		Always
    		10 to 14 V
    CPUB (P18-7) - Body ground
    		L-B - Body ground
    		+B power supply
    		Always
    		10 to 14 V
    SIG (P18-8) - Body ground
    		GR - Body ground
    		Ignition power supply
    		Ignition switch OFF → ON
    		0 V → 10 to 14 V


    Standard resistance:

    Symbols (Terminal No.)
    		Wiring Color
    		Terminal Description
    		Condition
    		Specified Condition
    GND (P18-1) - Body ground
    		W-B - Body ground
    		Ground
    		Always
    		Below 1 Ω

    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the R18 connector.

  4. Measure the voltage according to the value(s) in the table below.

    Standard voltage:

    Symbols (Terminal No.)
    		Wiring Color
    		Terminal Description
    		Condition
    		Specified Condition
    LMVR (R23-1) - Body ground
    		V - Body ground
    		Outer mirror switch signal (Up or Right)
    		Ignition switch ACC, Left/Right adjustment switch L side, Mirror switch OFF→ UP or Right
    		0 V → 10 to 14 V
    HTR+ (R23-4) - HTR- (R30-12)
    		B - B
    		Mirror heater signal
    		Mirror heater switch ON
    		0 V → 10 to 14 V
    LVC (R23-5) - Body ground
    		R-W - Body ground
    		Power source for mirror position sensor
    		Ignition switch OFF → ACC
    		0 V → 0 to 5 V
    VSSR (R23-6) - Body ground
    		Y-B - Body ground
    		Vertical direction position signal
    		Ignition switch ACC, Left/Right adjustment switch L side, Mirror switch uppermost position → lowermost position
    		0 V → 1 to 3V
    LMHR (R23-9) - Body ground
    		BR - Body ground
    		Outer mirror switch signal (Left or Down)
    		Ignition switch ACC, Left/Right adjustment switch L side, Mirror switch OFF→ LEFT or DOWN
    		0 V → 10 to 14 V
    LM+R (R23-10) - Body ground
    		R - Body ground
    		Outer mirror switch signal (Right or Down)
    		Ignition switch ACC, Left/Right adjustment switch L side, Mirror switch OFF→ RIGHT or DOWN
    		0 V → 10 to 14 V
    HSSR (R23-13) - Body ground
    		P - Body ground
    		Horizontal direction position signal
    		Ignition switch ACC, Left/Right adjustment switch L side, Mirror switch innermost position → outermost position
    		0 V → 1 to 3 V