FUEL PUMP > REMOVAL

for Preparation Click here

1. Remove the 5 nuts and front floor heat insulator No.3.
   

1. Disengage the 4 grommets.
   

2. Remove the screw and fuel tank protector sub-assembly No.1.
   

1. Remove the nut and disconnect the parking brake cable assembly No.3.
   

1. Separate the fuel tank wire connector from the bracket.
   

2. Disconnect the connector.
   

1. Remove the 3 bolts and charcoal canister protector.
   

1. Disconnect the fuel tank to canister tube sub-assembly from the charcoal canister assembly.
   
   

   1. Pinch the tube connector and then pull out the fuel tank to canister tube sub-assembly.
      

      NOTICE:

      1. Check for dirt or other foreign objects around the connector before this operation. Clean the connector as necessary.
         
      2. Be careful not to allow mud or foreign matter to scratch or come into contact with the pipe and connector that are sealed by an O-ring.
         
      3. Do not use any tools for this operation.
         
      4. Do not damage the disconnected pipe and connector. Prevent intrusion of foreign objects by covering the pipe and connector with a plastic bag.
         
      5. When the pipe and connector are stuck, push and pull the connector to release. Pull out the connector carefully.
         

2. Separate the fuel tank to canister tube from the clamp.
   

1. Pinch the tabs of the retainer to disengage the lock claws and pull the retainer down as shown in the illustration.
   

2. Pull out the fuel tank main tube.
   

   NOTICE:

   1. Check for dirt or other foreign objects around the connector before this operation. Clean the connector as necessary.
      
   2. Be careful not to allow mud or foreign matter to scratch or come into contact with the pipe and connector that are sealed by O-rings.
      
   3. Do not use any tools for this operation.
      
   4. Do not damage the disconnected pipe and connector. Prevent intrusion of foreign objects by covering the pipe and connector with a plastic bag.
      
   5. When the pipe and connector are stuck, push and pull the connector to release. Pull out the connector carefully.
      

1. Loosen the hose clamp bolt and disconnect the fuel tank to filler pipe hose.
   

2. Loosen the hose clamp bolt and disconnect the fuel tank breather hose.
   

1. Set a transmission jack to the fuel tank.
   

2. Remove the 4 bolts and the fuel tank bands.
   

3. Operate the transmission jack, and remove the fuel tank.
   

1. Disconnect the fuel pump connector.
   

2. Remove the tube joint clip and clamp, and pull out the fuel pump tube.
   

   NOTICE:

   1. Check that there is no dirt or foreign matter around the fuel tube joint. After cleaning off any dirt, proceed with the work.
      
   2. Be careful not to allow dirt or foreign matter to scratch or come into contact with the fuel tube connector and fuel suction plate that are sealed by O-rings.
      
   3. Do not use any tools for this work.
      
   4. Do not bend or twist the nylon tube by force.
      
   5. Cover the disconnected fuel tube joint with a plastic bag.
      
   6. When the fuel tube joint and fuel suction plate are stuck, pinch the fuel tank tube with your fingers, and turn it carefully to release. Disconnect the fuel tank tube.
      

3. Remove the 8 bolts and fuel tank vent tube set plate.
   

4. Pull out the fuel pump assembly from the fuel tank.
   

   NOTICE:

   1. Do not damage the fuel pump filter.
      
   2. Be careful not to bend the arm of the sender gauge.
      

5. Remove the gasket from the fuel suction tube.
   

1. Disconnect the fuel sender gauge connector.
   

2. Unlock the fuel sender gauge, then slide and remove it.
   

1. Disconnect the fuel pump connector.
   

2. Using a screwdriver with its tip wrapped with tape, disengage the 4 snap claws through the claw holes, and pull out the fuel suction plate.
   

   NOTICE:

   Do not damage the fuel suction support.

1. Disconnect the connector.
   

2. Using a screwdriver, pry out the fuel pump harness.
   

1. Using a screwdriver with its tip wrapped with tape, disengage the 4 snap claws through the claw holes, and remove the fuel suction support.
   

   NOTICE:

   Do not damage the fuel suction support.

1. Remove the fuel pump cushion rubber from the fuel pump.
   

1. Pull out the fuel pump from the fuel tank fuel filter.
   

1. Remove the fuel pressure with jet pump regulator assembly from the fuel tank fuel filter.
   

2. Remove the O-ring from the fuel pressure with jet pump regulator assembly.