STEERING COLUMN ASSEMBLY (for Manual Tilt) > REMOVAL

for Preparation Click here



1. PRECAUTION
(Click here)


2. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


3. REMOVE FRONT WHEEL LH


4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
(Click here)


5. REMOVE STEERING WHEEL COVER LOWER NO.3


    C111800

  1. Using a screwdriver, remove the steering wheel No.3 cover lower.

    HINT:
    Tape up the screwdriver tip before use.



6. REMOVE STEERING WHEEL COVER LOWER NO.2


    C111801

  1. Using a screwdriver, remove the steering wheel No.2 cover lower.

    HINT:
    Tape up the screwdriver tip before use.



7. REMOVE STEERING PAD ASSEMBLY


    C111802E01

  1. Using a "torx" socket wrench (T30), loosen the 2 "torx" screws until the groove along the screw circumference catches on the screw case.



    C111064

  1. Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand as shown in the illustration.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Disconnect the horn connector.

  1. Disconnect the 2 connectors from the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Remove the steering pad.



8. REMOVE STEERING WHEEL ASSEMBLY

  1. Remove the steering wheel assembly set nut.

  1. Put matchmarks on the steering wheel assembly and main shaft assembly.



    C111427E01

  1. Using SST, remove the steering wheel assembly.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)



9. REMOVE FRONT DOOR SCUFF PLATE LH


    B111782

  1. Disengage the 6 claws and 4 clips, and remove the front door scuff plate.

  1. Disconnect the connector. (w/ illumination scuff plate)



10. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    B108509

  1. Remove the 2 clips and the cowl side trim sub-assembly LH.



11. REMOVE INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LOWER


    B108510E02

  1. Using a screwdriver, open the instrument panel finish panel sub-assembly lower cover.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the bolt <A> and the screw <C>.

  1. Disconnect the hood lock control cable assembly.

  1. Disengage the 5 claws and the 4 clips.

  1. Disconnect the connectors and then remove the instrument panel finish panel sub-assembly lower.



12. REMOVE INSTRUMENT PANEL AIRBAG ASSEMBLY LOWER NO.1


    C111085

  1. Disconnect the connector from the driver side knee airbag assembly.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Remove the 4 bolts and the driver side knee airbag assembly.



13. REMOVE STEERING COLUMN COVER


    C111428E01

  1. Remove the steering column cover lower No.2.

  1. Remove the 3 screws.

  1. Disengage the 2 claws and remove the steering column cover lower.



    C111431

  1. Disengage the claw and remove the steering column cover upper.



14. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

  1. Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.



    C111432

  1. Using pliers, grip the claws of the clip and remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.



15. REMOVE AIR DUCT NO.1


    C111477

  1. Remove the bolt.

  1. Disengage the 3 claws and remove the air duct No.1.



16. SEPARATE STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


    C111429E01

  1. Loosen the bolt (A) and remove the clamp from the steering column hole shield.

  1. Loosen the bolt (B).

    HINT:
    Do not remove the bolt (B).



    C111478

  1. Remove the bolt, and then slide the steering intermediate shaft sub-assembly.

    NOTICE:
    Do not separate the steering intermediate shaft sub-assembly.



    C111430E01

  1. Put matchmarks on the steering intermediate shaft sub-assembly and the power steering link assembly.

  1. Separate the steering intermediate shaft sub-assembly from the power steering link assembly.



17. REMOVE INSTRUMENT PANEL FINISH PLATE


18. REMOVE STEERING COLUMN ASSEMBLY

  1. Disconnect the connectors and wire harness clamps from the steering column assembly.



    C111434

  1. Remove the 2 bolts, 2 nuts and the steering column assembly.



19. REMOVE STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


    C111435E01

  1. Put matchmarks on the steering intermediate shaft sub-assembly and the steering shaft universal joint assembly.

  1. Remove the bolt and the steering shaft universal joint assembly.



20. REMOVE STEERING COLUMN HOLE COVER SUB-ASSEMBLY NO.2


    C111447E01

  1. Remove the steering column hole cover sub-assembly No.2 from the steering intermediate shaft sub-assembly.



21. REMOVE STEERING SHAFT UNIVERSAL JOINT ASSEMBLY


    C112207E01

  1. Put matchmarks on the steering shaft universal joint assembly and the steering column assembly.

  1. Remove the bolt and the steering shaft universal joint assembly.