RADIO ANTENNA CORD > INSTALLATION

for Preparation Click here

1. Install the No.3 radio antenna cord with the bolt.
   
   

   
   
   
   

2. Engage the 11 clamps and connect the connector.
   

1. Tape the radio antenna cord at the position of the roof headlining assembly shown in the illustration.
   
   

   
   
   
   

1. Place the roof headlining to the vehicle from the back door side.
   

2. Engage the 2 fasteners and 3 clips. (w/o sliding roof)
   
   

   
   
   
   

3. Engage the 3 clips. (w/ sliding roof)
   

4. Install the sunroof opening trim moulding. (w/ sliding roof)
   

5. Connect the sliding roof drive gear connector. (w/ sliding roof)
   

6. Connect the washer hose. Connect the radio antenna cord connector and engage the clamps to the rear quarter pillar RH.
   

7. Connect the roof wire connector and engage the clamps to the front pillar LH.
   

8. Connect the washer hose. Connect the radio antenna cord connector and engage the clamps to the front pillar RH.
   

9. Install the radio antenna cord connector bolt to the front pillar RH.
   

1. Connect the connector.
   

2. Install the visor assembly with the 2 screws.
   

3. Engage the 4 claws and install the visor bracket cover.
   

1. Connect the connector.
   

2. Install the map light with the 4 screws.
   

3. Engage the claws and install the 2 caps.
   

4. w/o sliding roof:
   Engage the 6 claws and install the lens cover.
   

5. w/ sliding roof:
   Engage the 8 claws and install the lens cover.
   

1. Connect the connector.
   

2. Engage the 2 claws and 2 springs, and install the room light assembly No.1.
   

3. Engage the 4 claws and install the lens cover.
   

1. Connect the connector.
   

2. Install the rain sensor.
   

   NOTICE:

   1. If there is any residue left from the silicon sheet on the windshield, remove it.
      
   2. Clean the dirt on the glass with a cloth etc.
      
   3. When installing a new rain sensor, peel the release paper off from the silicon sheet first.
      
   4. Be careful not to leave any air bubbles in the rain sensor when installing it.
      

1. Install the assist grip sub-assembly with the 2 screws.
   

2. Engage the 6 claws and install the 2 assist grip covers.
   

   HINT:

   Use the same procedure for the other 3 assist grips.

1. Engage the 7 clips and install the roof side garnish assembly inner.
   

2. Install the 3 clips.
   

3. Install the 3 bolts and tonneau cover holder cap.
   

4. Engage the 4 claws and install the seat belt bezel.
   

1. Connect the connector.
   

2. Engage the claw and install the room light assembly No.2.
   

1. Engage the 2 clips and install the deck trim side panel assembly.
   

2. Install the 4 clips.
   

1. Install the 2 rope hooks with the 2 bolts.
   

   Torque:

   8.0 N*m{ 80 kgf*cm , 71 in.*lbf }

   HINT:

   Use the same procedure to install the other side.

1. Engage the 2 clips and install the rear floor finish side plate.
   

2. Install the clip.
   

1. Engage the 4 clips and install the rear seat side cover.
   

2. Install the 3 clips.
   

1. Install the rear No.1 seat outer belt assembly with the bolt.
   

   Torque:

   42 N*m{ 428 kgf*cm , 31 ft.*lbf }

1. Engage the 5 claws and install the deck side trim cover.
   

1. Engage the clip and install the center pillar garnish.
   

2. Install the 2 screws.
   

1. Engage the 2 clips and 3 claws, install the center pillar garnish lower.
   

1. Install the front seat outer belt assembly with the bolt.
   

   Torque:

   42 N*m{ 428 kgf*cm , 31 ft.*lbf }

1. Engage the 2 claws and install the lap belt outer anchor cover as shown in the illustration.
   

   HINT:

   Use the same procedure to install the other side.

1. Connect the connector. (w/ illumination scuff plate)
   

2. Engage the 4 claws and 2 clips, and install the rear door scuff plate.
   

1. Place the rear seat assembly LH in the vehicle and align the adjuster pin with the hole on the vehicle side.
   

2. Move the rear seat assembly LH to the rearmost position by operating the rear seat track adjusting handle.
   

   NOTICE:

   Check that the seat is locked.

3. Temporarily install the front side of the rear seat assembly LH with the 2 bolts.
   

4. Recline the separate rear seatback forward by operating the rear seat lock control lever sub-assembly.
   

5. Move the rear seat assembly LH fully forward.
   

   NOTICE:

   Check that the seat is locked.

6. Temporarily install the rear side of the rear seat assembly LH with the 3 bolts.
   

7. Return the separate rear seatback to the upright position.
   

8. Move the rear seat assembly LH to the rearmost position by operating the rear seat track adjusting handle.
   

   NOTICE:

   Check that the seat is locked.

9. Fully tighten the 2 bolts on the front side of the rear seat assembly LH in the order of the inner side bolt and then the outer side bolt.
   

   Torque:

   37 N*m{ 377 kgf*cm , 27 ft.*lbf }

10. Recline the separate rear seatback forward by operating the rear seat lock control lever sub-assembly.
    

11. Move the rear seat assembly LH fully forward.
    

    NOTICE:

    Check that the seat is locked.

12. Fully tighten the 3 bolts on the rear side of the rear seat assembly LH in the order of the inner rear side bolt, the inner front side bolt, and then the outer side bolt.
    

    Torque:

    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

13. Return the separate rear seatback to the upright position.
    

14. Move the rear seat assembly LH to the rearmost position by operating the rear seat track adjusting handle.
    

    NOTICE:

    Check that the seat is locked.

15. Install the floor anchor side of the fold seat stopper band assembly No.2 with the bolt.
    

    Torque:

    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

16. Install the 3 clips.
    

1. Place the rear seat assembly RH in the vehicle and align the adjuster pin with the hole on the vehicle side.
   

2. Move the rear seat assembly RH to the rearmost position by operating the rear seat track adjusting handle.
   

   NOTICE:

   Check that the seat is locked.

3. Temporarily install the front side of the rear seat assembly RH with the 2 bolts.
   

4. Recline the separate rear seatback forward by operating the rear seat lock control lever sub-assembly.
   

5. Move the rear seat assembly RH fully forward.
   

   NOTICE:

   Check that the seat is locked.

6. Temporarily install the rear side of the rear seat assembly RH with the 3 bolts.
   

7. Return the separate rear seatback to the upright position.
   

8. Move the rear seat assembly RH to the rearmost position by operating the rear seat track adjusting handle.
   

   NOTICE:

   Check that the seat is locked.

9. Fully tighten the 2 bolts on the front side of the rear seat assembly RH in the order of the inner side bolt and then the outer side bolt.
   

   Torque:

   37 N*m{ 377 kgf*cm , 27 ft.*lbf }

10. Recline the separate rear seatback forward by operating the rear seat lock control lever sub-assembly.
    

11. Move the rear seat assembly RH fully forward.
    

    NOTICE:

    Check that the seat is locked.

12. Fully tighten the 3 bolts on the rear side of the rear seat assembly RH in the order of the inner rear side bolt, the inner front side bolt, and then the outer side bolt.
    

    Torque:

    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

13. Return the separate rear seatback to the upright position.
    

14. Move the rear seat assembly RH to the rearmost position by operating the rear seat track adjusting handle.
    

    NOTICE:

    Check that the seat is locked.

15. Install the floor anchor side of the fold seat stopper band assembly No.1 with the bolt.
    

    Torque:

    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

16. Install the 5 clips.
    

1. Install the deck side trim box with the 2 clips.
   

1. Install the jack carrier assembly, jack assembly and jack carrier support.
   

1. Engage the 2 claws and 6 clips, and install the rear floor finish plate.
   

2. Install the 2 clips.
   

1. Install the deck No.3 board sub-assembly with the 2 bolts and 2 nuts.
   

1. Install the deck No.2 board sub-assembly with the 4 bolts and 2 nuts.
   

1. Install the deck floor box rear with the 2 clips.
   

1. Install the deck floor box front with the 2 clips.
   

1. Install the deck board sub-assembly with the 2 bolt.
   

2. Engage the 5 clips.
   

1. Engage the 6 clamps and install the No.2 radio antenna cord .
   

2. Install the navigation antenna with the 2 screws.
   
   

   
   
   
   

1. Engage the 6 clamps and install the No.2 radio antenna cord.
   
   

   
   
   
   

1. Connect each of the clamps and connectors.
   

2. Install the 2 bolts <A>, bolt <B>, and 2 nuts <D> as shown illustration below to install the instrument panel assembly.
   
   

   
   
   
   

   Torque:

   20 N*m{ 204 kgf*cm , 15 ft.*lbf } (Bolt <B>)

1. Engage the 3 clips and 2 claws, and install the instrument panel No.1 register assembly lower.
   

1. Engage the 2 clips and the 2 claws.
   

2. Install the screw <C>, nut <D>, and the instrument panel No.1 register assembly.
   

1. Install a new clip (A) on the front pillar garnish.
   

2. Engage the 2 claws and 2 clips, and install the front pillar garnish.
   

HINT:

Use the same procedures for the RH side and the LH side.

1. Engage the 2 clips.
   

2. Install the 7 screws <C> and the instrument panel finish panel lower center.
   

1. Slide the floor carpet cover center LH to the rear of the vehicle, and engage the 2 claws to the instrument panel finish panel lower center at the floor carpet cover center LH.
   

2. Install the 2 clips and the floor carpet cover center LH.
   

HINT:

Use the same procedures for the RH side and the LH side.

1. Connect the connectors.
   

2. Install the 2 bolts <A>, the 2 screws <C>, and the glove compartment door assembly.
   

1. Connect the connectors.
   

2. Engage the 3 claws and install the instrument panel No.2 under cover sub-assembly.
   

1. Install the driver side knee airbag assembly with the 4 bolts.
   

   Torque:

   7.6 N*m{ 78 kgf*cm , 68 in.*lbf }

2. Connect the connector to the driver side knee airbag assembly.
   

   NOTICE:

   When handling the airbag connector, take care not to damage the airbag wire harness.

1. Connect the connectors.
   

2. Install the 4 screws <C> and the combination meter assembly.
   

1. Engage the 4 clips and install the instrument cluster finish panel sub-assembly.
   

1. Connect the connectors.
   

2. Engage the 5 claws and the 4 clips.
   

3. Connect the hood lock control cable assembly.
   

4. Install the bolt <A>, the screw <C>, and the instrument panel finish panel sub-assembly lower.
   

1. Install the 2 clips and the cowl side trim sub-assembly LH.
   

HINT:

Use the same procedures for the RH side and the LH side.

1. Connect the connector. (w/ illumination scuff plate)
   

2. Engage the 6 claws and 4 clips, and install the front door scuff plate.
   

HINT:

Use the same procedures for the RH side and the LH side.

1. Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.
   

2. Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.
   

1. Engage the claw to install the tilt and telescopic switch.
   

2. Connect the connector.
   

1. Engage the claw to install the steering column cover upper.
   

2. Engage the 2 claws to install the steering column cover lower.
   

3. Install the 3 screws.
   

4. Install the steering column cover No.2.
   

1. Align the matchmarks on the steering wheel assembly and steering main shaft assembly.
   

2. Install the steering wheel assembly set nut.
   

   Torque:

   50 N*m{ 510 kgf*cm , 37 ft.*lbf }

1. Support the steering pad with one hand as shown in the illustration.
   

2. Connect the 2 connectors to the steering pad.
   

   NOTICE:

   When handling the airbag connector, take care not to damage the airbag wire harness.

3. Connect the horn connector.
   

4. Confirm that the circumference groove of the "torx" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.
   

5. Using a "torx" socket wrench (T30), tighten the 2 "torx" screws.
   

   Torque:

   8.8 N*m{ 90 kgf*cm , 78 in.*lbf }

1. Install the steering wheel No.3 cover lower.
   

1. Install the steering wheel No.2 cover lower.
   

1. Connect the connectors.
   

2. Engage the 4 clips and install the multi-display with the 2 bolts.
   

1. Install the connector.
   

2. Install the center cluster integration switch with the 2 bolts.
   

1. Install the No.2 radio bracket with the 3 bolts.
   

2. Install the No.1 radio bracket with the 3 bolts.
   

3. Connect the connectors.
   

4. Engage the 2 claws and the 2 clips.
   

5. Install the radio receiver with bracket with the 4 bolts.
   

1. Connect the connectors.
   

2. Engage the 2 clips and install the instrument panel finish panel lower.
   

1. Engage the 4 clips and install the console panel upper front.
   

1. Check that the left and right adjusters lock simultaneously when sliding the seat.
   

2. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.
   

NOTICE:

Some systems need initialization when disconnecting the cable from the negative battery terminal. (Click here)

1. With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:
   

   1. Cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.
      

2. Make sure that the horn sounds.
   

   HINT:

   If the horn does not sound, inspect the horn system (Click here).