INSTRUMENT PANEL SAFETY PAD > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT PASSENGER AIRBAG ASSEMBLY


2. INSTALL AUTOMATIC LIGHT CONTROL SENSOR


3. INSTALL INSTRUMENT PANEL NO.2 WIRE

  1. Engage the 18 clamps.



  1. Install the 2 screws and the instrument panel No.2 wire.


    B108531E02



4. INSTALL NO.2 RADIO ANTENNA CORD (w/ Navigation System)

  1. Engage the 6 clamps and install the No.2 radio antenna cord .



  1. Install the navigation antenna with the 2 screws.


    E110488



5. INSTALL NO.2 RADIO ANTENNA CORD (w/o Navigation System)


  1. Engage the 6 clamps and install the No.2 radio antenna cord.


    E110487



6. INSTALL GLOVE BOX LIGHT ASSEMBLY

  1. Engage the 2 claws and install the glove box light assembly.



    B108529

  1. Connect the connector.



7. INSTALL INSTRUMENT PANEL BRACKET SUB-ASSEMBLY CENTER


    B108530

  1. Install the screw <C> and the instrument panel bracket sub-assembly center.



8. INSTALL DEFROSTER NOZZLE NO.1 GARNISH


    B108533

  1. Engage the 2 clips and 4 claws, then install the defroster nozzle No.1 garnish.



9. INSTALL NETWORK GATEWAY ECU


    B108532

  1. Install the screw <C> and the network gateway ECU.



10. INSTALL DOOR OPENING RELAY ASSEMBLY


    B112166

  1. Install the screw <C> and the door opening relay assembly.



11. INSTALL WINDSHIELD WIPER RELAY ASSEMBLY (w/ Rain Sensor)


    B108528

  1. Install the screw <C> and the windshield wiper relay assembly.



12. INSTALL SIDE DEFROSTER NO.1 NOZZLE


    B108527

  1. Engage the 2 claws and install the side defroster No.1 nozzle.



13. INSTALL SIDE DEFROSTER NO.2 NOZZLE

HINT:
Use the same procedures for the side defroster No.2 nozzle and the side defroster No.1 nozzle.



14. INSTALL SIDE DEFROSTER NOZZLE NO.1 DUCT


    B108526

  1. Install the screw <C> and the side defroster No.1 nozzle duct.



15. INSTALL SIDE DEFROSTER NOZZLE NO.2 DUCT

HINT:
Use the same procedures for the side defroster No.2 nozzle duct and the side defroster No.1 nozzle duct.



16. INSTALL HEATER TO REGISTER CENTER SUB DUCT


    B108525

  1. Install the 2 screws <C> and the heater to register center sub duct.



17. INSTALL HEATER TO REGISTER NO.1 DUCT


    B108524

  1. Install the 4 screws <C> and the heater to register No.1 duct.



18. INSTALL HEATER TO REGISTER NO.4 DUCT

HINT:
Use the same procedures for the heater to register No.4 duct and the heater to register No.1 duct.



19. INSTALL DEFROSTER NOZZLE ASSEMBLY


    B108523

  1. Install the 3 screws <C> and the defroster nozzle assembly.



20. INSTALL INSTRUMENT PANEL NO.1 PIN


    B108534

  1. Install the screw <C> and the instrument panel No.1 pin.



21. INSTALL SIDE DEFROSTER NO.3 NOZZLE DUCT


    B108522

  1. Install the screw <C> and the side defroster No.3 nozzle duct.



22. INSTALL SIDE DEFROSTER NO.4 NOZZLE DUCT

HINT:
Use the same procedures for the side defroster No.4 nozzle duct and the side defroster No.3 nozzle duct.



23. INSTALL LIGHT CONTROL RHEOSTAT


    B108588

  1. Engage the 2 claws and install the light control rheostat.



24. INSTALL FRONT NO.2 SPEAKER


    E068292

  1. Connect the connector.

  1. Install the front No.2 speaker.



25. INSTALL FRONT NO.2 SPEAKER


    E068292

  1. Connect the connector.

  1. Install the front No.2 speaker.



26. INSTALL FRONT NO.2 SPEAKER (w/ Mark Levinson Speaker System)


    E068290

  1. Connect the connector.

  1. Install the front No.2 speaker with the 2 bolts.



27. INSTALL INSTRUMENT PANEL NO.1 SPEAKER PANEL SUB-ASSEMBLY


    B108583

  1. Engage the 2 clips and install the instrument panel No.1 speaker panel sub-assembly.



28. INSTALL INSTRUMENT PANEL NO.2 SPEAKER PANEL SUB-ASSEMBLY

HINT:
Use the same procedures for the instrument panel No.2 speaker panel sub-assembly and the instrument panel No.1 speaker panel sub-assembly.



29. INSTALL SPEAKER NO.1 HOLE COVER (w/ Mark Levinson Speaker System)


    B108520

  1. Engage the 4 clips and install the speaker hole No.1 cover.